Wine Master SP40CAPRO User manual

INSTALLATION AND USER
MANUAL
Installation and
(please keep this document
INDICATIONS STATED ON THE NAMEPLATE OF THE UNIT
oModel :
………………………………..
oSerial N° :
…………………………..
o
Purchase date :
………………………...
MANUAL
WINESP40CAPRO
Installation and
user manual
(please keep this document
carefully)
SP40CAPRO
INDICATIONS STATED ON THE NAMEPLATE OF THE UNIT
:
………………………………..
…………………………..
………………………...
Guide ref
:
Page 2
user manual
03/2015

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 3
User manual
Table of contents
1. TECHNICAL DATAS .................................................................................... 5
2. EQUIPMENT ............................................................................................... 7
2.1. Outside unit.......................................................................................................................7
2.2. Inside unit..........................................................................................................................7
2.3. Thermostat ........................................................................................................................7
2.4. Connection box .................................................................................................................7
2.5. Connection drawing .........................................................................................................7
2.6. Cellar insulation................................................................................................................8
2.6.1. Insulation of walls, ceiling and floor........................................................................................................9
2.6.2. The door ........................................................................................................................................................9
2.6.3. Insulation of other elements.....................................................................................................................9
3. INSTALLATION OF THE AIR CONDITIONER WINEMASTER
®
..................... 10
3.1. List of required material .............................................................................. 10
3.2. Installation of the outside unit ..................................................................... 10
3.2.1. rackets installation..................................................................................................................................10
3.2.2. Fixing the outside unit..............................................................................................................................10
3.3. Installation of the inside unit ....................................................................... 11
3.4. Ducting connection ..................................................................................... 11
3.5. Electric connection ..................................................................................... 12
3.5.1. Connection of outside unit.......................................................................................................................12
3.5.2. Connection of inside unit .........................................................................................................................12
3.5.3. Plugging.......................................................................................................................................................12
3.5.4. Wiring drawing...........................................................................................................................................13
3.6. Installation of the water drain system ........................................................... 14
4. PLUGGING THE AIR CONDITIONER WINEMASTER
®
................................. 14
4.1. Connecting the air conditioner ..................................................................... 14
4.2. Start up .................................................................................................... 15
4.2.1. Temperature setting .................................................................................................................................15
4.2.2. Standby mode ............................................................................................................................................15
4.2.3. Automatic defrost......................................................................................................................................15
5. MAINTENANCE OF THE AIR CONDITIONER WINEMASTER
®
..................... 16
5.1. Filter and outside unit cleaning .................................................................... 16
5.2. Condensates drain ...................................................................................... 16
6. WARRANTY .............................................................................................. 17
6.1. Legal warranty ........................................................................................... 17
6.2. 2 years contractual warranty ....................................................................... 17
6.3. Warranty conditions .................................................................................... 17
6.4. Exclusions and limitations of warranty .......................................................... 17
G

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 4
Introduction
You purchased an air conditioner WINEMASTER
®
and we thank you for your confidence.
From conception to marketing, everything has been implemented to offer an
exclusive and high quality product. rainchild of a team who find in this a motivation to
ever satisfy you, we hope that your wine conditioning unit WINEMASTER
®
will bring you
great storage conditions and best wines aging for an incomparable pleasure.
ecause the customer is at the heart of all our thoughts, we want to support you in your
first steps and lead you towards the best use of your air conditioner every day. Thus,
you will find in this manual technical information and practical advice to help you to deal
with the essential steps to installation and use.
In order that your wine tasting remains moments to share, WINEMASTER guarantees
you a sincere engagement, dedicated expertise and ongoing follow-up at your service!
WINEMASTER.

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 5
1. TECHNICAL DATAS
WINESP40CAPRO
Outside unit Inside unit
Weight of units 35 kg 17 kg
Dimensions H x L x D 408 x 633 x 415 262 x 517 x 327
Temperature setting
Preset at 12°C, adjustable between 4 & 15°C *
Maximum outside temperature.
40°C **
Cooling power
900 W at 15°C **
Electricity supply 230/240V-50 Hz
Electric power 600 W
Heating power 500 W
Gas R404A
The circuit breaker must be at least 16 Amps.
* The insulation has to be in accordance with the volume of the cellar and the set temperature.
** The cooling performance is dependant from the outside temperature. Therefore, the set temperature
of 12°C for the cellar cannot be maintained if the outside temperature reaches the 40°C.
If the thermal safety functions to often, there is a risk for the compressor to be damaged. In all cases, it
must be avoid that the outside temperature remains at 40°C, this high temperature should be limited
to the summer period.
VENTILATED COLD OR « NO FROST » ( schematic diagram)
The advantages of « ventilated cold »:
- No frost other than on the evaporator.
- Automatic defrosting and maximized refrigeration efficiency.
- Cold distribution improved by a permanent air circulation (without air stratification).
The circulation of air allows maintaining the pre-selected temperature throughout the cellar

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 6
Technical drawing
•Outside unit
•Inside unit
•Thermostat
•Wiring box

INSTALLATION AND USER
MANUAL
2. EQUIPMENT
The air conditioner is composed of 2 separate units, of a thermostat and a wiring box. They must be
connected by frigorific ducting pipes and electric connections.
The ducting pipes length between both
2.1.Outside unit
The unit must be installed outside or in a room.
If the unit is installed outside:
-
Place the unit in order the air suction and air rejection are not disturbed
-
Encourage the installation in open areas and sheltered from the sun
-
e cautious to the noise to the neighborhood
-Raise the unit to prevent
from
If the unit is installed in a room :
-
Place the unit in order the air suction and air rejection are not disturbed
-
Ensure there is a good ventilation
-Maximum temperature
and non permanent
-Ideal temperature ≈ 20°C.
2.2.Inside unit
Install the inside unit only in
side the cellar
2.3.Thermostat
The thermostat can be installed either inside or outside the
If installed outside, take into consideration the length of the temperature probe to be installed into the
cellar.
The delivered probe has a length of 1.5m.
minimal section of 0.5mm2.
2.4.Connection box
The connection box can be installed too either inside or outside the
If installed outside, take into
consideration the cable length ( 2 m)
2.5.Connection drawing
TAKE INTO CONSIDERAT
OUTSIDE UNIT
NO CA LE SUPPLIED
MANUAL
WINESP40CAPRO
The air conditioner is composed of 2 separate units, of a thermostat and a wiring box. They must be
connected by frigorific ducting pipes and electric connections.
The ducting pipes length between both
units should not exceed 20m.
The unit must be installed outside or in a room.
Place the unit in order the air suction and air rejection are not disturbed
Encourage the installation in open areas and sheltered from the sun
e cautious to the noise to the neighborhood
from
accumulation of water and snow
Place the unit in order the air suction and air rejection are not disturbed
Ensure there is a good ventilation
and non permanent
≤ 40°C
side the cellar
.
The thermostat can be installed either inside or outside the
cellar.
If installed outside, take into consideration the length of the temperature probe to be installed into the
The delivered probe has a length of 1.5m.
It
can be extended by flexible cable isolated to 2 drivers of
The connection box can be installed too either inside or outside the
cellar.
consideration the cable length ( 2 m)
TAKE INTO CONSIDERAT
ION THE CA LE LENGTH
S ETWEEN THE
CONNECTION OX AND THE UNITS
THERMOSTAT
CA LE LENGTH 2M
MAIN CONNECTION
NO CA LE SUPPLIED
Page 7
The air conditioner is composed of 2 separate units, of a thermostat and a wiring box. They must be
If installed outside, take into consideration the length of the temperature probe to be installed into the
can be extended by flexible cable isolated to 2 drivers of
S ETWEEN THE
INSIDE UNIT
CA LE LENGTH 2M

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 8
2.6.Cellar insulation
Insulation is essential for an efficient functioning of the WINEMASTER
®
. An appropriate insulation
enables to maintain a stable temperature and humidity level. The chart on the next page will allow
you to determine the type and thickness of insulation needed in relation to the exterior volume of the
cellar and the model of the WINEMASTER
®
, for an inside temperature of 12°C.
Insulation complement
The insulating elements should be preferably installed:
- y “tongue and groove “ panels or
- y fused together panels
IMPORTANT : Avoid heat and humidity intrusion which can alter their regulation
View
1. WALL
2. INSULATION MATERIAL
3. GROUND LEVEL
4. FLOOR
5. CEILING
6. INSULATED DOOR
IMPORTANT
The WINEMASTER
®
warranty is only valid if the insulation is in compliance with the board « Insulation
selection » requirements for the whole cellar (walls, floor, door and ceiling) with perfect continuity of
insulation.
Insulation selection
Volume of
the cellar
(m³)
Polystyrene
expanded = 0,044
W/m°C
(mm)
Polystyrene
extruded
= 0,030 W/m°C
(mm)
Polyurethane foam
= 0,025 W/m°C
(mm)
4 20 10 10
8 30 20 20
12 50 30 30
16 60 40 40
20 80 50 50
24 90 60 50
28 100 70 60
32 120 80 70
36 140 90 80
40 150 100 90
2

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 9
2.6.1. Insulation of walls, ceiling and floor
Type of insulation panels
You can select among the following type of panels:
- Usual panels,
- « Complex panels »: insulation is covered with a with a cover material (plaster, mineral …..)
- « Sandwich panels »: insulation is covered on each side with a wooden panel or plaster board.
Important: The covering of the panels protects the insulation against damage and guarantees its
longevity. Avoid using mineral fibres insulation (glasswool, rockwool, etc…) as they may
accumulate moisture and lose their insulation power and avoid also thin film insulation
that are not
effective for cold.
DO YOU KNOW THAT ?
Some insulating materials are damaged by rodents. If necessary, cover the insulation with a protective
lining on the inside of the cellar to avoid presence of mouse or rats.
 Polyurethane is an insulator that, due to its chemical composition, is not attacked by the
rodents.
Floor insulation
The floor of the cellar must be able to support the shelves and the stored wine. Thus, it’s necessary to
choose insulation with adequate compression strength.
Improve the load capacity of the insulation (particularly under the shelve legs) by using :
- « Complex » insulation panels covered by panels of higher load capacity.
- Cover the insulation panel with a wooden panel (at least 15 mm thickness), or every other
appropriated material.
2.6.2. The door
Door improves the insulation. Two solutions are possible:
- Insulate an existing door with the same insulation materials used for the walls of the
cellar. Provide a tight seal between the door frame and all sides of the door with a strip of foam
rubber for example.
Use a specially design WINEMASTER isothermal door with polyurethane and a sealing foam
View
1. INSULATED DOOR
2. INSULATION
3. SEALING TAPE
2.6.3. Insulation of other elements
Avoid placing a wine cabinet or freezer who generates heat in the cellar. The central heating pipes
should be re-isolated during their passage through the cellar.

INSTALLATION AND USER
MANUAL
3. INSTALLATION
OF THE AIR CONDITIONER
3.1.List of required
material
-A cord 4G1.5mm²
for outside unit connection
-A cord 3G1.5mm²
for the connection of wiring box
-Copper pipes 1/4" & 3/8"
for the cooling connection
-
Screws and tools for fixing the outside unit
3.2.
Installation of the outside unit
3.2.1.
rackets installation
3.2.2. Fix
ing the outside unit
MANUAL
WINESP40CAPRO
OF THE AIR CONDITIONER
WINEMASTER
material
for outside unit connection
for the connection of wiring box
for the cooling connection
Screws and tools for fixing the outside unit
Installation of the outside unit
rackets installation
-Trace
and drill the holes
-Unfold the
brackets and fi
the
ing the outside unit
-
Screw the 4 anti
-
Place the air conditioner on the brackets
-
Screw the 4 screw
spanner of 10
Page 10
WINEMASTER
®
and drill the holes
locations as
indicated
brackets and fi
x them with
the
adapted parts
Screw the 4 anti
-vibration pins on the unit
Place the air conditioner on the brackets
Screw the 4 screw
-washer M6 using a

INSTALLATION AND USER
MANUAL
3.3.
Installation of the inside unit
Due to the diversity of installations
and the type of locations, each installer must adapt to the constraints
of its installation.
3.4.Ducting connection
THE PIPE CONNECTION
oth units are loaded with an inert
gas (nitrogen). Connect the 2 units
line and 3/8" for the gas
line. The nuts are provided. Put them on the copper rigid pipe before performing
the extender.
The maximum length is of 20 m, the
must not exceed 10.
Lenghts
0-5 m
5 to 10 m
10 to 15 m
15 to 20 m
When all is working properly,
before disconnecting the
Disconnect then the pipes and
replace
SUCTION
MANUAL
WINESP40CAPRO
Installation of the inside unit
and the type of locations, each installer must adapt to the constraints
- Provide
openings
suction
and blowing
- Provide
space for
electrical connections and
the
condensate drain
- The suction
and blowing
be
even partially
-
The blowing and suction should be
separated to avoid a resumption of the air
supply,
even partia
suction tempera
ture should be the same
as the room temperature when the unit
produced cold)
THE PIPE CONNECTION
HAS TO E UNDERTAKEN
Y A PROFESSIONNAL
gas (nitrogen). Connect the 2 units
by a copper line 1/4" for the
line. The nuts are provided. Put them on the copper rigid pipe before performing
maximum elevation is 10 meters.
The number of bends
Gas loading (R404A)
900 g
1000 g
1100 g
1200 g
before disconnecting the
pipes
, unscrew fully the valves
replace
the gaps on the valves.
LOWING
Page 11
and the type of locations, each installer must adapt to the constraints
openings
on the bottom for
and blowing
space for
refrigeration and
electrical connections and
the passage of
condensate drain
and blowing
should in no way
even partially
obstructed
The blowing and suction should be
separated to avoid a resumption of the air
even partia
lly (for checking, the
ture should be the same
as the room temperature when the unit
Y A PROFESSIONNAL
.
by a copper line 1/4" for the
liquid
line. The nuts are provided. Put them on the copper rigid pipe before performing
The number of bends
per link
, unscrew fully the valves
.

INSTALLATION AND USER
MANUAL
3.5.Electric connection
3.5.1.
Connection of outside unit
-
Unscrew and remove the cover from outside unit
-
Unscrew the cover from the waterproof box
-
Connect the box and the outside unit via the
(§3.5.4)
- Close the waterproof box
- Close the outside unit
3.5.2.
Connection of inside unit
-
Unscrew and remove the front cover
- Pl
ug the power cord, as per wiring drawing
- Close the cover
3.5.3. Plugging
The connecting box has to be connected to a single phase power line p
230V - 16A.
THE UNIT HAS TO E INSTALLED RESPECTING THE NATIONAL RULES OF ELECTRIC
MANUAL
WINESP40CAPRO
Connection of outside unit
Unscrew and remove the cover from outside unit
Unscrew the cover from the waterproof box
Connect the box and the outside unit via the
4G1.5 cord (not supplied)
Connection of inside unit
Unscrew and remove the front cover
ug the power cord, as per wiring drawing
(§3.5.4)
The connecting box has to be connected to a single phase power line p
rotected by a circuit breaker
THE UNIT HAS TO E INSTALLED RESPECTING THE NATIONAL RULES OF ELECTRIC
INSTALLATIONS.
Page 12
as per wiring drawing
rotected by a circuit breaker
THE UNIT HAS TO E INSTALLED RESPECTING THE NATIONAL RULES OF ELECTRIC

INSTALLATION AND USER
MANUAL
3.5.4. Wiring drawing
MANUAL
WINESP40CAPRO
Page 13

INSTALLATION AND USER
MANUAL
3.6.
Installation of the water drain system
THE TU E DRAIN SHOULD NOT E
The condensate bucket may overflow if the drain is not directed downwards
4.
PLUGGING THE AIR CONDITIONER
The thermostat indicates the temperature in the wine cellar with a precision of 2°C. A temperature
variation of the air doesn’t mean the same variation of the liquid due to the thermal capacity of the liquid.
The thermostat is set at 12°C in the factory. D
controlled and adjusted as indicated
(§4.2.1)
4.1.
Connecting the air conditioner
When you plug the unit to the electric socket, the display indicates the temperature of the wine
cabinet :
-
If the temperature is over the thermostat
minutes.
-
If the temperature is under the thermostat
ventilator of inside unit works.
1
2
MANUAL
WINESP40CAPRO
Installation of the water drain system
-
The evacuation of the condensate is ma
drain pipe supplied with the unit
-Fit the drain pipe on the
bracket
supplied with the unit
-
The flow is done by gravity and must be connected to a
sewage or bucket that must r
egularly be
THE TU E DRAIN SHOULD NOT E
CLOOGED OR DO LOOP UP!
The condensate bucket may overflow if the drain is not directed downwards
PLUGGING THE AIR CONDITIONER
WINEMASTER
The thermostat indicates the temperature in the wine cellar with a precision of 2°C. A temperature
variation of the air doesn’t mean the same variation of the liquid due to the thermal capacity of the liquid.
The thermostat is set at 12°C in the factory. D
uring the installation, the set temperature must be
(§4.2.1)
.
Connecting the air conditioner
When you plug the unit to the electric socket, the display indicates the temperature of the wine
If the temperature is over the thermostat
setting:
the air conditioner starts running after 2
If the temperature is under the thermostat
setting:
the compressor doesn’t start.
ventilator of inside unit works.
Page 14
The evacuation of the condensate is ma
de through a
drain pipe supplied with the unit
bracket
(1) with a clamp (2)
The flow is done by gravity and must be connected to a
egularly be
emptied
The condensate bucket may overflow if the drain is not directed downwards
WINEMASTER
®
The thermostat indicates the temperature in the wine cellar with a precision of 2°C. A temperature
variation of the air doesn’t mean the same variation of the liquid due to the thermal capacity of the liquid.
uring the installation, the set temperature must be
When you plug the unit to the electric socket, the display indicates the temperature of the wine
the air conditioner starts running after 2
the compressor doesn’t start.
Only the

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 15
4.2. Start up
4.2.1. Temperature setting
The setting of the targeted temperature is made on the thermostat:
- Press on one second until the targeted temperature is blinking.
- Use to increase the temperature.
- Use to lower the temperature.
- Once the right temperature is set, press on again to confirm.
Explanations on the main display symbols: :
Red light = cold more engaged (compressor working)
Red light = cooling fan on high speed
Red light = defrost
Red light = heating mode engaged (resistance)
4.2.2. Standby mode
- Standby mode: maintain 3 seconds on button 1. The compressor stops
and the fan turns at low speed.
- The thermostat indicates « OFF » and also the cellar temperature.
- To come back, maintain again a 3 seconds pressure on button 1.
- The thermostat indicates « ON » during 1 second
-
4.2.3. Automatic defrost
The program of the thermostat will run an automatic defrost time several times a day. During this
operation, the compressor is stopped, only the fan is functioning at low speed. The condensate water
produced during this period will be evacuated through the tube drain.

INSTALLATION AND USER
MANUAL
5.
MAINTENANCE OF THE AIR CONDITIONER WINEMASTER
5.1. F
ilter and outside unit
The outside
unit is equipped with a washable and reusable filter.
CHECK AND CLEAN THE FILTER REGULARLY



DUSTED FILTER = DAMAG
CHECK AND CLEAR THE OPENINGS



CLOGGED AIR INLET = DAMAGED AIR CONDITIONER
5.2. Condensates drain
Check and clean the drain once
a year.
MANUAL
WINESP40CAPRO
MAINTENANCE OF THE AIR CONDITIONER WINEMASTER
ilter and outside unit
cleaning
unit is equipped with a washable and reusable filter.

Unscrew the 2 plastic screws (1)

Remove the filter cover (2)

Take the filter out (3)

Wash the filter with warm water

Once the filter cleaned and drained,
replace the filter back and close
CHECK AND CLEAN THE FILTER REGULARLY
DUSTED FILTER = DAMAG
E ON THE AIR CONDITIONER
CHECK AND CLEAR THE OPENINGS
REGULARLY
CLOGGED AIR INLET = DAMAGED AIR CONDITIONER
a year.
Page 16
MAINTENANCE OF THE AIR CONDITIONER WINEMASTER
®
Unscrew the 2 plastic screws (1)
Remove the filter cover (2)
Take the filter out (3)
Wash the filter with warm water
Once the filter cleaned and drained,
replace the filter back and close
the cover
E ON THE AIR CONDITIONER

INSTALLATION AND USER MANUAL WINESP40CAPRO
Page 17
6. WARRANTY
6.1. Legal warranty
The contractual warranty is not exclusive, earnings for the benefit of the purchaser profit of the legal
warranty against defects or hidden defects that applies under the conditions of article 1641 and following
from the civil code.
6.2. 2 years contractual warranty
WINEMASTER offers a 2 years warranty against any manufactured defect.
During this period of contractual warranty, WINEMASTER will replace any acknowledge defective part.
In case of electric failure, WINEMASTER reserves the right to check the appliance before replacing any
defective parts.
In case of refrigeration failure, WINEMASTER may require that the appliance is returned to the factory for
repair. Any interventions will take place according to the guidelines set in the ‘after sale service
document’.
Interventions and returns can only be done after written agreement from WINEMASTER after
sale service.
6.3. Warranty conditions
The contractual warranty applies to all appliance installed and used in conformity with this «user
manual ». His application is conditioned by the presentation of the purchase invoice or for lack of its
copy.
6.4. Exclusions and limitations of warranty
The warranty can be refused in following cases:
- Insulation of the cellar or installation of the appliance not in compliance with the instructions of this
guide.
- Damages due to negligence, lack of maintenance or incorrect use of the air conditioner
WINEMASTER
®
(particularly clogged filters.
- Exchange of parts or repair under warranty will not extend the 2 years warranty period.
WINEMASTER SAS cannot, in any case, be held liable for any direct or indirect damages resulting from
the failure of the air conditioner. The warranty is exclusively limited to the product itself.
The European Community is attaching a great importance to the environment and
the waste process, set up by a instruction N° 2002/96/CE relating to the electric and
electronic component waste (DEEE).
In accordance with this standard, the logo « crossed dustbin » is obligatory.
This logo means that the appliance may not under any circumstances be
thrown in the household garbage. It must be handed over to the appropriate
collection point for its treatment, recovery and recycling of wasted electric and
electronic components.
Acting like that, you make a gesture for the environment and contribute to the
safeguard of the natural resources as well as to the protection of human health.