Wine racks America Solid Diamond Bin User manual

Solid Diamond Bin
Assembly GUIDE
*Please verify that you have the correct number of parts before proceeding.
Depending on the model you purchased, your bundle should contain the following:
Package Contents tools for assembly
Page 1
or visit
wineracksamerica.com
Questions?
888.373.6057
TOP PANEL (x1)
BOTTOM PANEL (x1)
SIDE PANEL (x2)
SHIM (x1)
BOTTOM TRIM PIECE (x1)
WOOD SCREWS FINISH NAILS
HORIZONTAL SHELF PANEL (x1)
SHELF DIVIDER (DEPENDS ON MODEL)
34 7/8" 35 5/16"
33 7/8"
23 1/8"
34 7/8"
33 7/8"
10"
WOOD PUTTY
Cordless DrillFinish Nailer
Hammer Nail Setter
Rubber Mallet
Wood Glue
Required
Suggested
Screwdriver
Top Panel
Shelf Divider
Side Panel
Vertical Shelf Panel
Trim Piece
Bottom Panel
Side Panel
SCAN FOR
ASSEMBLY VIDEO
VERTICAL SHELF PANEL (x1)
33 1/2"
Horizontal
Shelf Panel

Solid Diamond Bin
Assembly GUIDEor visit
wineracksamerica.com
Questions?
888.373.6057
Page 2
1. Find an open, flat area in which to work. Carefully remove all components from the box and remove banding or
protective wrapping. Check the parts list to verify you have received a complete package.
1
ATTACH SIDES
TO BOTTOM
2. Using the provided wood screws, attach the bottom panel into the bottom grooves of the two side panels. (figure 1)
3. Attach the top panel to the side panel pieces using the wood srews provided. Make sure to keep the side panels
and top panel held tightly together when securing. It may be easier to stand the rack upright when securing the
top frame piece. (figure 2)
2
SECURE TOP
TO FRAME
BOTTOM
OF RACK

Solid Diamond Bin
Assembly GUIDEor visit
wineracksamerica.com
Questions?
888.373.6057
Page 3
4. Insert horizontal shelf panel into the grooves on the two side panels. Make sure the notch on the shelf panel
is facing downward. Attach using provided wood screws. (figure 3)
3
ATTACH HORIZONTAL
SHELF PANEL
4
INSERT VERTICAL
SHELF PANEL
5. Flip rack over and inset the vertical shelf panel into the notch on the horizontal panel and press into place.
Do not force into place. Use a rubber mallet if necessary. (figure 4)
* The horizontal shelf panel is similar to the vertical shelf panel. Make sure to use the longer panel in this step.

Solid Diamond Bin
Assembly GUIDEor visit
wineracksamerica.com
Questions?
888.373.6057
Page 4
6. Insert the shelf dividers into the frame to match your configuration (figure 5). If your rack did not include any
shelf dividers, please proceed to the next step.
5
INSERT SHELF
DIVIDERS
TIP: The dividers slide into place with little or no force. If necessary, use a rubber mallet to lightly tap the shelf
dividers into place.
BOTTOM
OF RACK
BOTTOM
OF RACK
7. At this point, there is no specific front of the rack. Choose the side of the rack that you would like to be the front
and secure the bottom trim piece. The bottom trim piece should be flush with the bottom of the rack. (figure 6)
We recommend that you use a finish nailer to drive a nail through the trim piece into each side frame piece.
If you do not have a finish nailer, drive one of the provided finish nails into each side frame piece using a hammer
until it is flush with the surface trim piece. Then, countersink the nail using a nail setter until the head of the
nail is about 1/16" below the surface of the wood. Use wood glue for added support.
Fill the nail holes using the wood putty provided. Push a small amount of putty into each hole and wipe excess putty
off the surface using a damp cloth.
BOTTOM
OF RACK
6
ATTACH BOTTOM
TRIM PIECE

Solid Diamond Bin
Assembly GUIDEor visit
wineracksamerica.com
Questions?
888.373.6057
Page 5
8. To prevent the bottom of the rack from bowing under the weight of your bottles, slide the bottom frame shim
under the back of the rack. (figure 7)
FRONT
OF RACK
7
INSERT SHIM BEFORE
LOADING BOTTLES
9. If you purchased a solid top, secure it by placing a small amount of wood glue on the top of the box frame. Clamp
the top to the frame using standard wood clamps until fully dry. (figure 8)
8
ATTACH
BUTCHER BLOCK
360 North 700 West Suite F • North Salt Lake, UT 84054
(toll free) 888-373-6057
(fax) 801-936-0534
Once again, thank you for your business. Remember, customer
service is available to answer any questions Monday-Friday
7:00 am - 5:00 pm MST. Please feel free to contact us for any
wine storage needs.
We would love to see your wine racks in use! Please feel free to
send any photos of your rack to [email protected]
WINERACKSAMERICA.COM