STEP
2
Remove protective
battery tab-pull
STEP
3
Attach transmitting unit
to wall with adhesive
strips (included)
STEP
5
“Learn”
WaterBug
transmitter into
the control panel
Enable
“Programming
Mode”
Open and close the
case to “tamper” the
device
ADD
Customize name and
settings as desired and
touch “ADD”
FCC / IC Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence
standard RSS (s). Son fonctionnement est soumis aux deux conditions
suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2)
cet appareil doit accepter toute interférence, y compris celles pouvant
causer un mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human exposure to radio
frequency elds, the radiating element shall be installed such that a
minimum separation distance of 20 cm is maintained from the general
population.
FCC: 2ABBZ-WIN-WATER-319
IC: 11817A-WINWATER-319
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation. Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
This Class B digital apparatus complies with Canadian ICES-3B.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
MANUFACTURERHEREBY DISCLAIMS ALL WARRANTIES AND REPRESENTATIONS, WHETHER EXPRESS,
IMPLIED, STATUTORY OR OTHERWISE INCLUDING (BUT NOT LIMITEDTO) ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TOTHESE PRODUCTS AND ANY
RELATEDSOFT WARE. MANUFACTURER FURTHER DISCLAIMS ANY OTHER IMPLIED WARRANTYUNDER THE
UNIFORM COMPUTER INFORMATIONTRANSACTIONS ACT OR SIMILAR LAW AS ENACTED BY ANY STATE.
(USA only) SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIEDWARRANTIES, SO THE ABOVE
EXCLUSION MAY NOT APPLY TOYOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTSAND YOU MAY
ALSO HAVE OTHERLEGAL RIGHTS THAT VARY FROM STATE TO STATE.
MANUFACTURERMAKES NO REPRESENTATION, WARRANTY,COVENANT OR PROMISE THAT ITS ALARM
PRODUCTS AND/OR RELATED SOFTWARE(I) WILL NOT BE HACKED, COMPROMISED AND/OR CIRCUMVENTED;
(II) WILL PREVENT,OR PROVIDE ADEQUATE WARNING OR PROTECTION FROM, BREAK-INS, BURGLARY,
ROBBERY, FIRE; OR (III) WILL WORK PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS.
NEED HELP?
800-635-4269 Ext 1
D-011-0173
Rev. A
Mount the
Transmitter above
the oor level (as
high as reasonably
possible) to prevent
water damage.
• Transmitter: 2.71” L x .95”W x .56” D
• Tamper Switch: Included inside transmitter
• Probe Dimensions .7” W x 1.77” L x .38” D
• Cord length 6’
• Wireless signal range: 600ft (200M), open air
• Transmitter frequency: 319.5 MHz
• Unique code ID:
• RF Peak eld strength: typical 36000 uV/m at 3m
• Operating Temperature: 32° to 122°F (0° to 50°C)
• Relative Humidity: 5 - 95% Non-Condensing
• Storage Temperature: -40° to 140°F (-40° to 60°C)
• Supervisory keep-alive interval: 70 minutes
• Code outputs: tamper, tamper restore, alarm, alarm
restore, low battery
• Batteries: 2 – CR2032. Approximate Battery Life: 5 years
Replace Batteries: (2) Panasonic CRT2032, Energizer
CR2032, or Duracell DL2032
STEP
4
Attach probe to
oor or oor
baseboard with
adhesive strips
(included).
Tie o extra cord as
needed or desired.
