Winmate WM-CONTROL-SS Instructions for use

Temperature and Humidity Control
Installation, Use & Care Manual
WM-CONTROL-SS
!!! " # $ %& ' ( ) *"+& ) ,
,
,
- $ %& ' ( ) * , . % ' ( / % 0 ' $ &% 0 1 , 2 & / * ,
34563,7, 7890%0, :&0;,:0%+<&,=&)$%>8(?@, 2A, BCDD3 ,
E(1F, GHCCI, 444 , - . J K,
L0MF,G63CI, HH5 N 663C ,
O)0$1F,,$% P &Q # $ %& ' ( ) *" + & ) ,
,
,
Read and save these instructions

- 1 -
Temperature and Humidity Control WM-CONTROL-SS
15S-601 is microprocessor-based controller to be connected to the 15S-602
keypad by means of a two-wire cable at a distance of up to 100 ft. It is provided
with four relay outputs to control liquid line solenoid valve, evaporator fan
(adjusting humidity), and alarm auto-dialer and cellar heater. It is also provided
with up to 4 NTC or PTC probe inputs for cellar temperature and evaporator
temperature control, bottle temperature and condenser temperature monitor. The
controller is fully configurable through special parameters that can be easily
programmed through the keypad. The controller can be connected to internet
based 15S-WEB module through external module 15S-CX. The keypad is thin and
has a stainless steel face which can be perfectly integrated into a wall.
1. Keypad and Controller
1) How to use keypad
SET: To display set-point; in programming mode it selects a parameter or confirms
an operation.
: To start a manual defrost.
: To see the maximum stored temperature; in programming mode it browses
parameters or increases displayed values.
: To see the minimum stored temperature; in programming mode it browses
parameters or decreases displayed value.
: To turn on or off the power to the unit.
+ : To lock or unlock the keypad.
SET + : To enter in the programming mode.
SET + : To return to the temperature display.

- 2 -
2) How to lock and unlock the keys
Press and until POF is displayed to lock the keys; Press and until PON
is displayed to unlock the keys.
3) Display
During normal operating conditions, the display shows the value measured by the
air temperature probe. In case of active alarm, the temperature flashes alternately
to the code alarm. The LED functions are listed as follows.
LED
MODE
FUNCTION
ON
Compressor and liquid line solenoid valve
enabled
Flashing
Anti-short cycle enabled
ON
Defrost cycle enabled
ON
Fan enabled
Flashing
Fan delay after defrost enabled
ON
Alarm occurring
ON
Temperature measuring unit
Flashing
Programming mode
4) Alarm Signals
The alarm codes are described as follows.
MESSAGE
CAUSE
FUNCTION
P1
Temperature probe faulty
Compressor switching to Con and CoF
HA
High temperature alarm
Probe temperature ALU higher than the
setting temperature; Outputs unchanged
LA
Low temperature alarm
Probe temperature ALL lower than the
setting temperature; Outputs unchanged
CA
External alarm
All outputs off
Probe alarms P1”, start a few seconds after the fault in the related probe; they
automatically stop a few seconds after the probe restarts normal operation. Check
connections before replacing the probe. Temperature alarms “HA”, “LA”
automatically stops as soon as the temperature returns to normal value. Alarm
“CA” (with i1F=PAL) recovers only by switching off and on the instrument.
2. Temperature Setting
• Set the temperature at 55 °F for the optimum aging of wine
• On initial start-up, the time required to reach the desired temperature will vary,
depending on the quantity of bottles, temperature setting and surrounding
temperature.
• Allow 24 hours to stabilize the temperature for each new temperature setting
operation

- 3 -
3. How to see temperature set-point
1) Press and immediately release SET key, the display will show the set-point.
2) Press again and immediately release the SET key to display the probe value.
4. How to change the set-point
1) Press and hold the SET key until the “°C” or “°F” LED starts flashing and the
set-point is displayed.
2) Press or to change the set-point value within 10 sec.
3) Press the SET key again to store the new set-point value.
NOTE: The unit turns on at set-point Set plus regulation differential Hy after anti-
short cycle AC has elapsed; the unit turns off at set-point Set.
5. How to start manual defrost
Press and hold until defrost starts. The defrost indicator will be displayed.
6. How to activate quick cooling
Press and hold until for more than 3 seconds. The compressor and liquid
line solenoid valve indicator will be displayed.
7. How to program parameters
1) Press and hold SET and until the “°C” or “°F” LED starts flashing, then
release the keys.
2) Press and hold again the SET and keys until the Pr2 label is displayed, then
release the keys. The first parameter Hy will be displayed.
3) Press or to scroll to the required parameter within 10 sec.
4) Press the “SET” key to display its value.
5) Use or to change its value within 10 sec.
6) Press “SET” to store the new value and the display will flash 3 times.
7) To exit: Press SET and or wait 15sec without pressing a key.
PARAMETER
DESCRIPTION
DEFAULT VALUE
Set
set-point (°)
55
Hy
temperature regulation
differential (°)
4
AC
anti-short cycle delay (min)
10
Con
compress on with probe faulty
(min)
15
CoF
compress off with probe faulty
(min)
30
CF
temperature unit (°F/ °C)
F: Fahrenheit
rES
display resolution
in: integer
dLy
temperature display delay (min)
1

- 4 -
ot
probe calibration (°)
0
LS
minimum set-point (°)
50
US
maximum set-point (°)
65
idF
defrost cycle interval time (hour)
12
MdF
defrost cycle endurance time
(min)
30
ALC
temperature alarm type
rE: relative to set-point
ALU
high temperature alarm (°)
10
ALL
low temperature alarm (°)
10
AFH
alarm recovery differential (°)
5
ALd
temperature alarm delay (min)
60
dAO
temperature alarm delay on
startup (hr)
23
SAA
heater set-point (°)
40
SHy
heater regulation differential (°)
4
FSU
fan action
Std
FnC
fan operating mode
C-n: on with compressor & off
during defrost
Fon
fan on with compressor off (min)
0
FoF
fan off with compressor off (min)
15
NOTE: Depending on the controller, not all parameters are used.
8. How to calibrate the air probe
If the actual cellar temperature differs from the setting temperature, set parameter
ot = actual cellar temperature minus set-point.
9. How to adjust defrost cycle
In case there is excessive frost, the parameters FnC = C-y, idF = 4 and MdF = 20
can be used to avoid frost.
10. How to adjust the humidity
The parameter Fon is used to adjust the humidity in the wine cellar. Higher Fon
results in higher relative humidity. Use a separate hygrometer to monitor the
humidity.
11. How to set alarm call
1) Speech notice will be sent to your phones when the cellar temperature is ALU
higher or ALL lower than the set-point Set.
2) In order to test the call function, set parameters Ald = 0 and dAO = 0. After
testing, set Ald = 60 and dAO = 23.
12. How to set cellar heater
The heater turns on at SAA minus Shy; the heater turns off at SAA.

- 5 -
NOTES:
• Use a forced air heater to warm up the wine cellar.
• If there is a thermostat on the heater, bypass it or set the thermostat at the
highest level.
• If the heater runs more than 10 A current, use a 120VAC coil contactor.
13. Controller & Electrical Wiring Diagrams
NOTES:
• To use call feature connect the terminals 20 and 21 to the auto-dialer power
supplier 120V input.
• To use cellar heater feature connect the terminals 22 and 23 to the cellar heater
120V input.
• To use bottle probe feature connect the terminals 2 and 3 to the bottle probe
input.
1) FAN COIL 120V Electrical Wiring (WM-SFCD, WM-SFCI, WM-SFCL, WM-
SFCO, WM-SFCS, WM-SFCW)

- 6 -
2) AIR HANDLER 120V Electrical Wiring (WM-SFCA, WM-SFCH, WM-SFCR,
WM-SFCV)
3) CONDENSING UNIT 120V Electrical Wiring (WM-150~450SCUR)

- 7 -
4) CONDENSING UNIT 120V Electrical Wiring (WM-650SCUR)
5) CONDENSING UNIT 120V Electrical Wiring (WM-850SCUR)

- 8 -
6) CONDENSING UNIT 230V Electrical Wiring (WM-1203SCUR)
7) CONDENSING UNIT 120V Electrical Wiring (WM-250~650SCUR-WC)

- 9 -
8) CONDENSING UNIT 120V Electrical Wiring (WM-850SCUR-WC)
9) CONDENSING UNIT 230V Electrical Wiring (WM-1203SCUR-WC)

- 10 -
Customer Support
If you need further assistance, please contact us at:
Vinotemp International
17631 South Susana Road
Rancho Dominguez, CA 90221
Tel: [phone]
Fax: [phone]
Email: [email protected]

- 11 -
Warranty
Thank you for choosing a Vinotemp cooling unit.
Please enter the complete model and serial numbers in the space provided:
Model______________________________________________________
Serial No.___________________________________________________
Attach your purchase receipt to this owner’s manual.
1. Limited Warranty
VINOTEMP warrants its products to be free from defects due to workmanship or
materials under normal use and service, for twelve months after the initial sale. If
the product is defective due to workmanship or materials, is removed within twelve
months of the initial sale and is returned to VINOTEMP, in the original shipping
carton, shipping prepaid, VINOTEMP will at its option, repair or replace the product
free of charge. Additionally VINOTEMP warrants compressor to be free from
defects for a period of sixty months after initial sale.
This warranty constitutes the entire warranty of the VINOTEMP with respect to its
products and is in lieu of all other warranties, express or implied, including any of
fitness for a particular purpose. In no event shall VINOTEMP be responsible for
any consequential damages what is so ever. Any modification or unauthorized
repair of VINOTEMP products shall void this warranty.
Service under Warranty
This service is provided to customers within the continental UNITED STATES only.
VINOTEMP cooling units are warranted to produce the stated number of BTU/H.
While every effort has been made to provide accurate guidelines, VINOTEMP
cannot warranty its units to cool a particular enclosure.
In case of failure, VINOTEMP cooling units must be repaired by the factory or its
authorized agent. Repairs or modifications made by anyone else will void the
warranty.
Shall a VINOTEMP cooling unit fail, please contact the dealer for instructions. Do
not return the unit to the factory without authorization from VINOTEMP. If the unit
requires repair, re-pack it in the original shipping carton and return it to the factory,
shipping prepaid. VINOTEMP will not accept COD shipments. If the unit is

- 12 -
determined to be faulty and is within the twelve month warranty period VINOTEMP
will, at its discretion, repair or replace the unit and return it free of charge to the
original retail customer. If the unit is found to be in good working order, or beyond
the initial twelve month period, it will be returned freight collect.
2. Limitation of Implied Warranty
VINOTEMP’S SOLE LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED
TO, AT OUR OPTION, REPAIRING OR REPLACING OF UNIT.
VINOTEMP SHALL NOT BE LIABLE FOR:
DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE UNIT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE UNIT,
LOSS OF TIME OR COMMERCIAL LOSS, ANY OUTER DAMAGES, WHETHER
INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR INPLIED, INCLUDING BUT NOT LIMITED TO,
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
While great effort has been made to provide accurate guidelines VINOTEMP
cannot warrant its units to properly cool a particular enclosure. Customers are
cautioned that enclosure construction, unit location and many other factors can
affect the operation and performance of the unit. There for suitability of the unit for
a specific enclosure or application must be determined by the customer and cannot
be warranted by VINOTEMP.
For further details of our terms, please review at www.vinotemp.com/Terms-and-
Conditions.aspx.