Winmate M270TF-XXX User manual

User Manual
M270TF-XXX
M320TF-XXX
LCD Monitor
Before operating the unit, please read this manual thoroughly and retain it for future reference.

- 2 -
Table of Contents
Preface......................................................................................................................... - 4 -
Owner’s Record......................................................................................................... - 4 -
What is Included........................................................................................................ - 4 -
Chapter 1: Hardware Installation................................................................................... - 5 -
Installation................................................................................................................. - 5 -
Connecting Cables.................................................................................................... - 6 -
Ground Pin................................................................................................................ - 6 -
Connecting Power..................................................................................................... - 7 -
Hard Power On.......................................................................................................... - 7 -
Hard Power On...................................................................................................... - 7 -
Hard Power Off...................................................................................................... - 7 -
Soft Power On and Off .............................................................................................. - 8 -
Power Modes ............................................................................................................ - 8 -
Chapter 2: Operating the Device................................................................................... - 9 -
IR Remote Control..................................................................................................... - 9 -
On Screen Display (OSD) Navigation...................................................................... - 10 -
OSD Locking / Unlocking......................................................................................... - 11 -
Hot Keys.................................................................................................................. - 11 -
Quick Key................................................................................................................ - 11 -
Basic OSD Menu Options: Display.......................................................................... - 14 -
Basic OSD Menu Options: Adjust............................................................................ - 16 -
Basic OSD Menu Options: Audio............................................................................. - 18 -
Basic OSD Menu Options: Multi-Display.................................................................. - 19 -
Basic OSD Menu Options: OSD.............................................................................. - 21 -
Basic OSD Menu Options: ADVANCED.................................................................. - 22 -
Chapter 3: Important Information ................................................................................ - 24 -
Indications for Use / Intended Use........................................................................... - 24 -
Customers in the U.S.A........................................................................................... - 24 -
Customers outside the U.S.A .................................................................................. - 24 -
Important safeguards/notices for use in the medical environments ...................... - 25 -
Important EMC notices for use in the medical environments................................ - 25 -

- 3 -
Warning and Cautions.............................................................................................- 29 -
Safety...................................................................................................................- 31 -
Installation............................................................................................................- 31 -
Precautions for connecting this unit with other medical devices ...........................- 31 -
Use with an electrosurgical knife, etc. ..................................................................- 32 -
Precautions for using this unit safely....................................................................- 32 -
Recommendation to use more than one unit........................................................- 32 -
About the LCD Display Panel ..................................................................................- 33 -
Images that may cause burn-in............................................................................- 33 -
To reduce the risk of burn-in.................................................................................- 33 -
About the screen protect panel.............................................................................- 33 -
A long period of use.............................................................................................- 34 -
Moisture condensation.........................................................................................- 34 -
Cleaning before cleaning......................................................................................- 34 -
Cleaning the monitor............................................................................................- 34 -
Flat surface for better maintenance......................................................................- 35 -
Repacking............................................................................................................- 35 -
Disposal of the unit...............................................................................................- 35 -
Biological Hazard and Returns.................................................................................- 36 -
Frequency Table......................................................................................................- 37 -
Troubleshooting.......................................................................................................- 38 -
Appendix A: Technical Specification............................................................................- 39 -
Dimensional Figure..................................................................................................- 47 -
27” Model.............................................................................................................- 47 -
32” Model.............................................................................................................- 47 -
Appendix B: Meaning of Symbols on the unit ..............................................................- 48 -

- 4 -
Preface
Owner’s Record
The model and serial numbers are located at the rear of the unit. Record these numbers in
the spaces provided below. Refer to these numbers whenever you call upon your Winmate
dealer regarding this product.
Model No. Serial No.
What is Included
27” / 32” 4K Display
Remote Control
User Manual
M4 VESA Mounting
Screws
Part number depends on
the configuration the unit
9B0000000418
10mm x 8 pcs
12mm x 8 pcs
15mm x 8 pcs
24 Volt power supply
Power Cable 1.8m
VGA cable
DVI Cable 1.8 m
922D150W24V4
Varies on the country
9441151150P3
9455295290Q0
SDI Cable
USB Cable for
Touch (Optional)
DC Jack to Open
Wire Cable
9470020020K1
948018102100
94JQ02L020K2

- 5 -
Chapter 1: Hardware Installation
Installation
To access the connectors, remove the connector cover. Before removing the connector
cover, disconnect the power cord.
1. Remove the four screws on the connector cover.
2. Slide the connector cover in the direction of the arrow and remove it.
WARNING !
Do not remove any other screws other than the four screws
affixing the connector cover. Doing so may cause electric shock.

- 6 -
Connecting Cables
1.
24 V DC In
6.
VGA In
11.
Mic In
2.
Dual DVI in
7.
HDMI 2.0
12.
Line Out
3.
HDMI 1.4
8.
SDI In
13.
RS-232
4.
DP1.2 Out
9.
SDI Out
14.
USB 2.0
5.
DP1.2 In
10.
RJ-11
15.
Power 5V Out
There are several video and/or data cables that can be connected in many combinations.
The number and type of connections will be automatically detected by the monitor. From the
OSD (On Screen Display) the user can select the way the images will be displayed.
Be sure to tighten and thumb screws on the individual video cable. A secure connection is
important to ensure the best image quality.
Ground Pin
Connect this monitor to the Protective Earth ground at this pin. This Pin is also used when
potential equalization between the monitor and other equipment is required. Simply connect
the potential equalization pin (POAG) found on devices, to the monitor ground pin using an
AWG18 wire (WIRE NOT PROVIDED).

- 7 -
Connecting Power
Connect the AC cord to the AC IN terminal on the AC adaptor.
Connect the DC OUT terminal of the AC adaptor to the DC IN terminal on the
monitor.
Align the notch on the cord connector with the guiding groove and plug it in.
Connect the AC cord plug to the power outlet.
Hard Power On
Hard power and soft power are used independently. The differences explained below:
Hard Power On
Turn the POWER switch at the bottom of the monitor to On. The POWER indicator
glows blue, indicating the monitor is internally powered.
Hard Power Off
Turn the POWER switch at the bottom of the monitor to off. The POWER indicator
light turns off, indicating the monitor is not internally powered.

- 8 -
Soft Power On and Off
The soft power button, when touched, will enable or disable the video screen. The soft
power button need only be touched once. Depending on monitor’s current state, there may
be a few second delay in displaying an image.
Power Modes
This table shows the LED light combinations and their meaning:
Blue
Amber
Description
ON
OFF
Power On Mode
Image being displayed
ON
ON
Searching for a signal
OFF
ON
No signal found or stand-by mode
OFF
OFF
Soft Power Off Mode
The soft power button was pressed
OFF
OFF
Hard Power Off Mode
No image being displayed

- 9 -
Chapter 2: Operating the Device
IR Remote Control
All the monitor controls can be accessed through the IR remote control. This controller has
a few quick access keys for the user’s convenience.
Soft Power
Quick Key –initiates Quick Menu
Central Key –Contains: Volume
increase / decrease, down/ less,
up/more, and enter
PIP Key –initiates the Picture in
Picture Features.
Source Key –Initiates the next
active video input
Zoom In Key –Initiates Zoom In
Swap Key –Initiates an image
swap during a 2P mode
Mute Key –Activates or
deactivates speakers
Zoom Out Key –initiates the
Zoom out

- 10 -
On Screen Display (OSD) Navigation
When the Enter key is touched, the OSD (On Screen Display) menu will appear on the
monitor screen. This menu offers the user ability to make many changes to the image. The
table below shows the response after touching the different OSD icons
Icon
OSD Menu Status
Response
Displaying
Close OSD menu
Off
Open the Quick menu
Displaying
Enter
Off
Open OSD Menu
Displaying
Move down / Decrease value
Off
N/A
Displaying
Move up / Increase value
Off
Auto Adjust
Displaying
Disable Video Image
Off
Enable Video Image

- 11 -
OSD Locking / Unlocking
Touching both the and buttons simultaneously will either turn ON or OFF the OSD
lockout feature.
LOCKED
UNLOCKED
Hot Keys
Touching either the or the button will initiate the brightness control feature.
Quick Key
The OSD Function key QUICK offers the user easier access to six major monitor
adjustment.
The sub-menu under the SOURCE 1 option allows the user to select the video source for
the primary image.

- 12 -
The sub-menu under ZOOM allows the user the ability to select which image to zoom into.
Depending on the Display Mode previously selected, different regions to apply the zoom
function are displayed.
The sub-menu under SCHEME offers the user six (6) color schemes to choose from. Each
color scheme can be adjusted individually under the OSD function DISPLAY, menu option
SCHEME ADJUST. The primary colors and secondary colors are adjustable.

- 13 -
Under Profile, the sub-menu offers the user six (6) different previously saved 3D LUT (Look
Up Table) profiles to select from. Profile can be uploaded using the Tomlinson Color
calibration software (not included).
Source 1
Set Main Video Input
Zoom
Zoom in / Zoom out of an image
Scheme
Select the uploaded scheme file
Scheme 1 to 6
Profile
Select from 6 standard color profiles
Medical and Custom 1 to 5
*profile can be changed with optional calibration software
2 Image Swap
Swap the images under 2 image mode
Source Scroll
Change input source

- 14 -
Basic OSD Menu Options: Display
The OSD offers a variety of monitor adjustment capabilities. Below is a description of a few
common functions used.
Under SCHEME ADJUST, the HUE and Saturation of each primary and secondary color can
be changed. These changes are stored under the SCHEME currently activated. (Found
under the Quick Menu)
Under COLOR CONTROL, the RED, GREEN, and BLUE colors of the current image are
changed.
These adjustments DO NOT over write the setting of SCHEME or PROFILE.
Region allows the user to select the “region(s)” / input(s) to adjust with a feature.
Example: Monitor has four inputs signals activated on a quad screen. There are nine (9)
possible region combinations that can be adjusted. In the picture below, only quadrant “1”
will receive adjustment.

- 15 -
Brightness
Adjusts the overall image and background brightness
Value: 0-100
Contrast
Adjusts the image contrast in relationship to the background
Value: 0-100
Sharpness
Adjusts the crispness of the image
Value: 0 to 4
ADC
Brightness
Adjusts the Auto Display Control (ADC) brightness
Value: 0-100
Temperature
Adjusts the color temperature of the entire screen.
USER/5600/6500/7600/9300
Note: low color temperature makes the screen reddish.
High color temperature makes the screen bluish.
Color Control
Adjusts the level of red, green, blue, yellow, magenta, and cyan
colors
RGB Slide Bar
Value: 0-100
Gamma
Select a display gamma value for best picture quality.
Native 1.8 / 2.0 / 2.2 / 2.4 / DICOM
*DICOM Can be calibrated using optional calibration software
Scheme
Adjust
Select scheme for different default setting combination.
Adjust the appearance of the Active Scheme
Hue
Adjust the level of hue
Value: 0-100
Saturation
Adjust the level of saturation
Value: 0-100
Region
Select the multi-source
1P
1/2P,2/2P ,1+2/2P
1/4P,2+3+4/4P
2/4P, 1+3+4/4P
3/4P, 1+2+4/4P
4/4P,1+2+3/4P,1+2+3+4/4P

- 16 -
Basic OSD Menu Options: Adjust
The ADJUST feature will automatically adjust an analog image.
When an analog image is initially detected, the monitor will attempt to automatically adjust
the image positioning.
This automatic adjustment feature can be turned On/Off here.
Adjust the white balance automatically here by selecting PRESS ENTER

- 17 -
AUTO Adjust
Automatically adjusts screen size, H position, V position, Clock,
Clock Phase when video source is changed
H Position
Controls the horizontal position of the image within the display
area of the LCD.
Value: 0-100
V Position
Controls the vertical position of the image within the display area
of the LCD.
Value: 0-100
Clock
(Adjust H total)
+ Expand the width of the image on the right of the screen
-Narrow the width of the image on the left of the screen
Value: 0-100
Phase
Adjusts the image phase
Value: 0-100
White Balance
Perform the white balance

- 18 -
Basic OSD Menu Options: Audio
The speaker volume for all audio inputs is controlled here.
AUDIO SOURCE allows the user to select which from the available inputs. Example, there
are 3 regions within the Quad display with audio.
Volume
Adjusts the level of volume
-Decrease +Increase
Value: 0-100
Mute
ON/OFF
Audio Source
Select the Audio Source
Audio IN, Fiber, 1P, 2P, 3P, 4P

- 19 -
Basic OSD Menu Options: Multi-Display
Display mode offer the user up to five different layouts to view input images
Each source can be assigned an active image (only one source can be set to auto scan)

- 20 -
Under the PIP layout position and size of the inner image can be adjusted
Display Mode
Choose the Display Mode
Full, 2PLR, 2PTB, PIP or QUAD
Source 1
Choose the channel of display source
Auto Scan/VGA/DVI/HDMI 2.0/HDMI 1.4/DP
Source 2
Choose the channel of display source
Auto Scan/VGA/DVI/HDMI 2.0/HDMI 1.4/DP
Source 3
Choose the channel of display source
Auto Scan/VGA/DVI/HDMI 2.0/HDMI 1.4/DP
Source 4
Choose the channel of display source
Auto Scan/VGA/DVI/HDMI 2.0/HDMI 1.4/DP
2P LR Ratio
RATIO 0/1/2/3/4
PIP Size
Adjust picture-in-picture(PIP) size
Value: 0-10
PIP Position-H
Adjust the horizontal position of PIP
Value: 0-100
PIP Position-V
Adjust the Vertical position of PIP
Value: 0-100