Wintec Mini POS IDT600 User manual

Mini POS
IDT600
Hardware Manual
Qingdao Wintec System Co., Lt d
Technology & Solution
Carrera 3 No. 73-91
PBX (57 1) 321 2199 FAX [phone]
Bogotá - Colombia

Preface
Copyright
Thispublication,includingallphotographs,illustrationsand
software,isprotectedunderinternationalcopyrightlaws,with
allrightsreserved.Neitherthismanual,noranyofthematerial
containedherein,maybereproducedortransmittedinany
formwithoutexpress writtenauthorizationfromWintec.
TrademarkAcknowledgments
Wintec istrademarksofWintec SystemCo.,Ltd.Allrights
reserved.
Otherproductnamesmotionedhereinmaybetrademarksor
registeredtrademarksoftheirrespectivecompanies.Wintec
claimsnointerestintrademarksotherthanitsown.
Disclaimer
Theinformationinthisdocumentissubjecttochangewithout
notice.Themanufacturermakesnorepresentationsor
warrantieswithrespecttothecontentshereofandspecifically
disclaimsanyimpliedwarrantiesofmerchantabilityorfitness
foranyparticularpurpose.Themanufacturerreservestheright
torevisethispublicationandtomakechangesfromtimeto
timeinthecontenthereofwithoutobligationofthe
manufacturertonotifyanypersonofsuchrevisionorchanges.

IDT600
Safety Information
Before installing and using the IDT600, take note of the
following precautions:
Do not place the unit on an unstable surface, cart or stand;
Do not block the slots and opening on the unit, which are
provided for ventilation;
Do not push objects in the ventilation slots as they may
touch high voltage components and result in shock and
damage to the components;
Only use the power source indicated on the marking label.
If you are not sure, contact your dealer or the Power
Company;
The unit uses a three-wire ground cable, which is equipped
with a third pin to ground the unit and prevent electric
shock. Do not defeat the purpose of this pin. If your outlet
does not support this kind of plug, contact your electrician
to replace your obsolete outlet;
Do not place anything on the power cord. Place the power
cord where it will not be in the way of food traffic;
Follow all warnings and cautions in this manual and on the
unit case;
When replacing parts, ensure that your service technician
uses parts specified by the manufacturer;
Avoid using the system near water, in direct sunlight, or
near a heating device;

IDT600
TABLE OF CONTENTS
General 1
About the Product .........................................................................1
Specification...................................................................................2
Identifying Components ...............................................................3
System Design 8
IDT600 system diagram...............................................................8
Core Board ......................................................................................9
Main Board....................................................................................10
Key parts in Board.........................................................................12
Key Components 15
LCD Module..................................................................................15
Printer ............................................................................................16
Barcode scanner.............................................................................17
GPRS Module................................................................................18
Modem Module .............................................................................19
WiFi Module .................................................................................20
RF Card Reader .............................................................................21
WARRANTY 22
Having the IDT600 Serviced.........................................................22

IDT600
1
CHAPTER 1
General
Thank you for purchasing our powerful IDT600!
With this manual, you can operate and maintain the IDT600.
About the Product
IDT600 is an innovation of Intelligent Data Terminal developed by
Wintec. It integrates telephone voice, data processing and
communication functions, supports various means of
communication, such as ADSL, GSM, GPRS, WiFi, PSTN, etc…
and can be customized by third-party software. IDT600 plays an
important role in ndustry marketing information application.
IDT600 can be used for many industrial applications, such as
industrial distribution, retails, concept stores, financial services,
restaurants, logistics, etc…
IDT600 is a customerized, easy developing, maintenance and
upgrading POS, its functions can be tailored by different demands,
and highly flexible. Also the SKD provided facilitates the third-party
software developing in a short time.
Features:
•A comprehensive, standard, open operating systems and
database platform,
•Enable the third-party software developed with flexible andopen
hardware, communication drivers and the developing interface.
•Modular hardware design for easy upgrades and maintenances.
•Integrated the various communication methods (such as SMS,
GPRS, ADSL, Modem, LAN, Wifi , voice, etc.)
•Integrated thermal receipt printer.
•Touchscreen with graphical interface enhances user-friendly
operation
•Different ports for peripherals (USB, serial, etc.)
•Enables remote maintenance

IDT600
2
Specification
Note
1Maybe there are some difference for different Application !
CPU ARM9 203MHz
Memory 64MB
Rom Disk 64MB Nand Flash
Display 3.5”TFT LCD, 320×240
Keyboard 31Keys
Speaker 2W optional
IC Card reader ISO7816
Printer 58mm Thermal printer, paper ease load
Interface 1*RS232(internal 2),2*USB, 1*RJ45,
1*RJ11, SD card
Power Adapter 8V / 5A
Operating Temp. 0°C ~ 45°C
Operating Humidity 10% ~ 90% RH
Dimensions (mm) 270(W)×170(D)×92(H)
OS Linux or Win CE
3rd Party support SDK for Linux and Win CE
Options
Mobile Module GPRS
Touch screen 4-wires
Barcode Scanner 1D or 2D Scanner
RF Card reader RF card
Modem 56K

IDT600
3
Identifying Components
IDT600 view
DESCRIPTION
1 Barcode scanner windows
2 IC card reader
3 power switch
4 keyboard
5 TFT display and touch screen
6 status LED
7 printer paper slot
8 RF card antenna
9 speaker
10 holder for printer

IDT600
4
IDT600Keyboard
Keyboard default define as list:
This is the default define of the keys, including number keys(12keys),
directional keys(5keys), and shortcut keys(4keys) and function
keys(10), including ESC and Enter. You can define the function of the
keys, usually the F5 is FEED for printer. Enter and OK are the same.
note
1.you’d better only change the define of the keys “F6-F12”
2.you can define multi keys for the same function
3.you’d better use “F1-F4”for menu operation
IDT600 LED indication
DESCRIPTION
1 power LED!the green LED light is power on
2 state LED!the red LED is on or flash, don’t turn off
3 Communication LED!the yellow LED is on when
communicating Via GPRS, Ethernet or Modem…

IDT600
5
Interface view
No. DESCRIPTION
1GPRS or WiFi antenna
2DC power port
32*USB (down one slave)
4RJ45 for Ethernet
5RS232(DB9)
6Modem or telephone port
note
1 " Maybe there are some difference for different spec, the telephone
port is only for GPRS telephone function
2
"
you can connect the barcode scanner, scale or customer display
via RS232

IDT600
6
IDT600 assembly view

IDT600
7
DESCRIPTION
1CCD induction board 2 Screw
3 Ni-MH Battery 4 Screw
5CCD tray"battery cover#6 Screw
7CCD module"optional#8 Screw
9 Printer controller 10 Screw
11Printer tray 12 Thermal printer
13 Printer wheel 14 Paper cutter
15 MODEM module"optional#16 Screw
17 RF reader"optional#18 Screw
19 RF reader antenna 20 Upper case
21 Paper roll 22 Paper cover
23 Pinter holder 24 Screw
25 waterproof net for speaker 26 Speaker"optional#
27 Lens of LED 28 LED light
29 Screw 30 Keys caps
31 Conductive rubber 32 Keyboard PCB
33 Screw 34 dustproof strip
35 TFT Protective plates 36 TFT display (Touch screen)
37 TFT tray 38 Screw
39 Screw 40 WiFi Module"optional#
41 GPRS"or WiFi#antenna 42 Mainboard"Core /GPRS#
43 Screw 44 Power switch
45 Down case 46 Foot pad
47 Screw 48 SIM card cover
Note
1the options maybe are changed according to the customer’s
requirement.

IDT600
8
CHAPTER 2
System Design
IDT600 system diagram
Note
1$the parts included in the broken frame are used for some special
solution.

IDT600
9
There are 2 circuit board in the IDT600,core board and main board .The Core board
includes CPU, memory ,Flash memory and real timer etc…,the others parts are
included in main board
Core Board
Core board front view
Core board back view

IDT600
10
Main Board
Main Board front view
DESCRIPTION
1 IC card slot 2 core board
3 GPRS module
P1 Audio Interface P2 LED Interface
P3 RJ11 (modem or telephone)
P5 JTAG Interface P6 TFT LCD Interface
P7 RS232 P8 Keyboard Interface
P9 Voice COMM. Interface 1 P10 power port
P11 Power switch Interface P12 RJ45
P15
P3
P12
P13
P10
3
2
1
P17
P8
P
6
P18
7
P
2
P
1
P7
P21
P5
P14
P9
P11
P16
P20

IDT600
11
P13 USB port P14 Internal USB Interface
P15 RS232 port P16 Battery Interface
P17 Voice COMM. Interface 2 P18 Printer Interface
P20 Printer power Interface P21 RS232 Interface
Main Board front view
DESCRIPTION
U9 Micro SD card slot
U19 SIM Card slot
U9
U19

IDT600
12
Key parts in Board
CPU S3C2410A
16/32-Bit RISC architecture and powerful instruction set
with ARM920T CPU core
Enhanced ARM architecture MMU to support WinCE,
EPOC 32 and Linux
Address space: 128M bytes for each bank (total 1G bytes),
Eight memory banks(Six memory banks for ROM, SRAM,
and others; Two memory banks for ROM/SRAM/
Synchronous DRAM )
Supports programmable 8/16/32-bit data bus width for each
bank
Supports booting from NAND flash memory, after booting,
Supports storage memory for NAND flash memory
MPLL generates the clock to operate MCU at maximum
266MHz @ 2.0V.
55 Interrupt sources (One Watch dog timer, 5 timers, 9
UARTs, 24 external interrupts, 4 DMA, 2 RTC, 2 ADC, 1
IIC, 2 SPI, 1 SDI, 2 USB, 1 LCD, and 1 Battery Fault)
3-channel UART: Programmable baud rate ;Supports 5-bit,
6-bit, 7-bit, or 8-bit serial data transmit/receive (Tx/Rx)
Touch Screen Interface
Supports STN LCD Displays and TFT(Thin Film Transistor)
Color Displays
2-port USB Host, Compatible with USB Specification
version 1.1
ch IIS-bus for audio interface: Supports IIS format and
MSB-justified data format
NAND FLASH K9F1208
Unique ID for Copyright Protection
Reliable CMOS Floating-Gate Technology
Endurance : 100K Program/Erase Cycles(with 1bit/512Byte
ECC)
Data Retention : 10 Years
Hardware Data Protection: Program/Erase Lockout During
Power Transitions
Memory Cell Array : 64Mx8bits
supports Nand flash memory from 32MB to 256MB

IDT600
13
NOR FLASH:SST39VF6401B
(special use)
Superior Reliability
Endurance: 100,000 Cycles (Typical)
Greater than 100 years Data Retention
Security-ID Feature: SST: 128 bits; User: 128 bits
supports Nand flash memory from 2MB to 8MB
SDRAM HY57V561620
system memory:64MB
Ethernet CHIP CS8900A
(optional)
full duplex operation
netspeed:10MB
Audio UDA1341TS
(optional)
decided by embedded system software and player software
Power supply
input:+8V/5A
GRPS power input: DC-DC output 3.9V-3.0A
system power input: DC-DC output 5.0V-2.0A
CPU core voltage:1.8V
chip voltage:3.3V
Real Timer PCF8563
Provides year, month, day, weekday, hours, minutes and
seconds based on 32.768 kHz quartz crystal
Wide operating supply voltage range: 1.0 to 5.5 V
I2C BUS
battery can support real time chip work at last 10 years
error real timer less 1 minute per year
LED Indication
power LED indication
system state LED indication
Communication LED indication

IDT600
14
BEEP Indication
system runs error ,beep alarm
Keyboard
support max 5*8keys (only uses 31keys)
IC Card Interface
Support Memory card and CPU card
JTAG Debug Interface
support software debug on CPU running
Printer Interface
GPIO driver Printer Head
LCD Interface
3.5inch TFT LCD display,320*240 (w/touch screen)
USB Port
USB PORT 0/1: MODE(host interface)support USB mouse,
USB keyboard, USB disk, etc
RS232 Interface (3* RS232)
COM0:for external RS232 port
COM1: for Barcode scanner or other module (with standard
and TTL interface )
COM2: for GPRS or Modem (TTL)
Thermal Printer
58mm printer
Printing method: Direct thermosensitive method
Valid printing width: 48 mm
Dot Structure : 384Dots/line
Dot pitch (resolution) :0.125 mm (8 dots/mm)

IDT600
15
CHAPTER 3
Key Components
LCD Module
IDT600 uses 3.5”TFT LCD module,
Display Mode: Normally White
Display Technology: α-Si TFT active matrix
Viewing Area(mm): 72.88(W)X55.36(H)
Active Area(mm): 70.08(W)X52.56(H)
Resolution: 320X(RGB)X240 dots
Pixel Pitch: 219X219%m
Pixel Configuration: RGB Stripe
Backlight: 6 LED
Response time:50ms
Luminance: 200 cd/m
2
(Type)
Contrast ratio: 250
Signal Interface: Digital 24-bits RGB
Viewing Direction: 6 o’clock
Touch Panel (optional)
Touch Type: 4 wires resistive
Viewing Area (mm): 72.0 (W)X54.56(H)
Active Area (mm): 70.08(W)X53.26(H)
Visible light transmission :>80%
Linearity tolerance: X<1.5%,Y <1.5%
Operating Temp. :-20 °C to 70 °C
Storage Temp. : -40 °C to 80 °C

IDT600
16
Printer
IDT600 uses 58mm thermal printer,
ITEM Specifications
Printing method Direct thermosensitive method
Valid printing width 48 mm
Dot structure 384dots /line
Dot pitch(rsolution) 0.125 mm (8 dots/mm)
Dot size 0.125 ! 0.12
Printing specifications
Printing speed 60mm/s
Font 12×24(ANK),24×24(Chinesse)
Column capacity 32(12×24),36(12×24)
Character set IBM Character set II, B2312(Chinese)
Print font
Character per inch 16.9 cpi
Dimensions(W×OD) 58×45 mm
Paper
Thickness 0.06-0.07mm
Reliability (MCBF) 50Km