Wintime Centurion series User manual

Tablet LCD Monitor
User’s guide
User’s guide
Centurion
series
www.wintime.com.tw
TM
Pioneering pen computing
PN: 49-60003-010

This equipment has been tested and found to comply with the limits for a Class B digital
device,pursuanttoPart15ofFCCRules.Theselimitsaredesignedtoprovidereasonable
protection against harmful interference when the equipment is operated in a residential in-
stallation.
Thisequipmentgenerates,uses,andcan radiate radiofrequencyenergy and ifnotinstalled
andused inaccordancewith theinstructionmanual may causeharmfulinterference toradio
communications.However,thereisno guaranteethatinterference willnotoccur inaparticu-
larinstallation.
Ifthisequipmentcausesharmfulinterferencetoradioortelevisionreception,whichcanbe
determinedbyturning the equipment off and on, the user is encouragedtotrytocorrectthe
interferenceby one or moreofthe following measures:
Reorientthe receivingantenna.
Increasethe separationbetween the equipmentandreceiver.
Connectthe equipment intoanoutlet on acircuitdifferentfrom that towhichthe receiver is
connected.
Changes or modifications not expressly approved by the party responsible for compliance
can void the user's authority to operate the equipment. This product is equipped with a
shielded cable. Extension cables, if used, must be shielded in order to comply with the
emission limits. Operation of this device is subject to the following conditions: (1) This de-
vice may not cause harmful interference, and (2) this device must accept any interference
received,including interference thatmaycauseundesired operation.
FCC compliance statement
CE compliance statement
This product complies with all the requirements of the EMC Directive 89/336./EEC. This
product hasbeen tested and foundtocomplywith:
zlEN55022(CISPR22) - Electromagnetic interference.
zlEN50082-1(IEC801-2, IEC801-3, IEC801-4) - Electromagnetic immunity
zlEN60950(IEC60950)-Productsafety
Disclaimer and limitation of liability
WintimeElectronicsCorp. assumes no responsibility for any damage or loss resulting from
theuse of this manual. Wintime Electronicswillnotbe liable for technical ortypographical
errorsin this document, norforincidentalor consequential damages resultingfromthe use
ofthismaterial. Wintime Electronics Corporation also reserves the right tochangeproduct
specificationswithoutpriornotice.Nopartofthisdocumentmaybecopied,reproduced,or
transmittedby any means,foranypurpose without priorwrittenpermissionfrom Wintime
ElectronicsCorporation.
Trademarks
Microsoft,Windows,Windows CE and any other trademarksrelatedtoMicrosoftproducts
aretrademarksof Microsoft.Allothertrademarks used in this manual belong to their re-
spectiveowners.
©2003WintimeElectronics Corporation.All rights reserved.

Chapter 1
Introduction..........................................................................
Hardwareinstallation...........................................................
Chapter 2
Installing the device driver into Windows Me / 2000 / XP...
Chapter 3
Installing the device driver into Windows 98 ......................
1
2
3
5
7
Chapter 4
Customizingthe digital pen ................................................ 10
Appendix A
Removal of previous graphics tablet drivers ..................... 12
Contents
Contents
Appendix B
On screen display (OSD) settings ..................................... 13
Appendix C
Taking care of your tablet LCD monitor .............................. 14
Appendix D
Productspecifications ........................................................ 15
Pioneering pen computing

Thankyou for purchasing theCenturiontablet
LCDmonitor,whichallowsyoutowork directly
onthe screen and offers an alternative tokey-
boardandmouse.You can navigate your cur-
sor, and design,paint,draw,writeor sign inan
intuitiveandnaturalwaybymeansofWintime’s
exclusivewirelessandpressure sensitivedigi-
talpen.
Introduction
TheCenturion tablet LCD monitorprovidesoptimum hand-eye coordination, allowingusers
toworkwithapenonthescreenaseasyasonnormalpaper. This input device is designed
foreverybody whowantsto creativelyandefficiently design, producedocuments, and make
presentations.Its versatility makes the Centurion the ultimate tool forgraphicandindustrial
design,3D-animationandgamedesign,multimedia,education,databasemanagement,and
theproductionof audio and video.
Wireless and pressure sensitive stylus pen
Witha pressure sensitivity of 1024levels,thedigital pen is anidealtoolto intuitively draw or
manipulatedigitalimages,andforshadinginsketches.Bypressingharderonthetipofthe
penyoucaneffectively createthickerorstrongerlines ordosedigitalpaintto createstunning
artwork.
Freely programmable pen buttons
Thebuttons of the digital pen arefreelyprogrammableand you may add orcustomizetheir
functionaccording to your ownpersonalpreferences (see chapter 4).
System requirements
- PentiumPCorequivalentrunningWindows98/ Me / 2000 / XP
- 128MB or more RAM
- USB port
- 200MB available hard disk space
- CD-ROMdrive
Chapter 1
Chapter 1
2
Pioneering pen computing

Hardwareinstallation
Box contents
TheCenturion packagecontains thefollowing items.If you find any items lacking, please contact your dealer
immediately. Store all packing materials and accessories in a safe place in case the product needs to be
shippedin the future.
Centurion tablet LCD monitor
USB cable
AC/DC power adapter
Power cord with DC jack
Quick installation guide
Pressure sensitive digital pen
AAA size battery for digital pen
Install - CD-ROM (containing user’s guide and drivers)
Warranty card
Installing and connecting the Centurion tablet LCD monitor
2. Place the monitor on your desktop,
allowinga minimum space of 10cm (4-
inch) between the case and the wall. This
willensure thatthe monitorreceives
sufficientventilation throughthe slotsat
the back.
1.After unpacking, adjust the screen angle
toan appropriate position. Release metal
leverAby pressingand holding itdown
and then sliding stand Bup or down to the
desiredangle.
3. Connect the VGA cable to
yourcomputer.Thesuppliedmonitor
cable connects to the 15-pin VGA port
on your PC.
4.Plug thepower adapterinto thepower
jack of the tablet LCD monitor and theAC
powerplug ofthe adapter in a mains wall-
outlet.
Hardwareinstallation
3

5.Connectthe powercord tothe power adapter
and the power plug to the mains power outlet. 6. Connect the USB connector of the USB
cable to the USB port of your monitor.
Installing the digital pen battery
1. Turn both parts of the digital pen as
indicated. 2. Pull both parts apart as shown.
3. Carefully push theAAAbattery into place.
Tip: Alkaline batteries last significantly longer.
Hardwareinstallation
4

Installing the device driver into Windows Me / 2000 / XP
1. Switch on your computer and connect the USB connector to the USB port of your computer
2. TheNewHardware Found wizardwillfind
the tablet and install the “USB Human
InterfaceDevice”
3. InserttheDriver andManualCD-
ROM. If your system has the
“Autorun”functionenabled, your
screen will display the main menu.

Ifthe main menu did notappear, double-
click My computer on the Windows
desktop,and thenthe CD-ROM icon and
the Autorun.exe file in succession.
4. In the main menu choose English.
Inthefollowing screen chooseDriver
Installation.
5. Read the instructions on the screen
and click green arrow to launch the
installationprogram.
What you need for this installation:
the Tablet LCD Monitor install CD-ROM
If you have previously had another graphics tablet installed, or you are
reinstalling the tablet LCD monitor driver, you must first remove the
present driver from your system. Please refer to Appendix A for instruc-
tions.
Chapter 2
Chapter 2
5
Pioneering pen computing

7. Setup is complete, click OK, and you
may now use your tablet LCD monitor.
Installingthe devicedriver intoWindows Me / 2000 / XP
6. In the WintimeTablet Setup screen
click the Finish button.This will then
installthedevice driver.
In some setups of Windows 2000 and
WindowsXP aMicrosoft Digital Signature
warningmay appear onyour screen.Click
Yes to continue the installation.
6
Note: Please refer to Wintime’s website at
www.wintime.com.tw fortutorials to get
you started.

What you need for this installation:
the Tablet LCD Monitor install CD-ROM
your Windows 98 install CD-ROM
If you have previously had another graphics tablet installed, or you are
reinstalling the tablet LCD monitor driver, you must first remove the
present driver from your system. Please refer to Appendix A for instruc-
tions.
1. Switch on your computer and connect the USB connector to the USB port of your computer
2.TheAddNewHardware wizard will
then prompt you to install the USB
devicedriver.ClickNext.
3. Select “Display a list of all drivers in
a specific location, so you can select
the driver you want” and click Next.
Installing the device driver into Windows 98
4. In the following two screens click
Next.5. This will then prompt you to insert the disk
labeled“Windows 98 CD-ROM”. Click OK.
Chapter 3
Chapter 3
7
Pioneering pen computing

Installingthe device driverinto Windows 98
6. Insertyour Windows98 CD-ROM in
theCD-ROM drive. Inthe dialog box
that opens, click on the Browse
button.
7.Inthe Drives fieldselect your CD-ROM
drive(e.g. e:) In the Folders field select
Win98. Click OK and then OK again.
In the following screen click on the Finish
button.
8.RemoveyourWindows 98 CD-ROM
and replace it with the Tablet LCD
Monitorinstall CD-ROM. If your
system has the “Autorun” function
enabled, your screen will display the
mainmenu.

Ifthe main menu did notappear, double-
click My computer on the Windows
desktop,and thenthe CD-ROM icon and
the Autorun.exe file in succession.
9. In the main menu choose English
asyour language. Inthe following
screenchoose Driver Installation.
10. Read the instructions on the screen
and click green arrow to launch the
installationprogram.
8