Wire Tech 5000P-10x User manual

6PSDSC-IP-5000P
Series
PSDR-5000-42S2 CAM + IP
PSDR-5000-30S2 CAM
Multi-Format Professional HDTV Processor
User Manual
Ver. 2.3

- 3 -
Contents
1. Before Use the Device ............................................................................................................... 1
2. Introduction................................................................................................................................. 2
3. Installation .................................................................................................................................. 3
3.1 Inspection.......................................................................................................................... 3
3.2 Operating Voltage............................................................................................................. 3
3.3 The fuses........................................................................................................................... 3
3.4 Connecting Up the Device................................................................................................ 3
3.5 Power On the Device........................................................................................................ 4
4. Navigating the Front Panel......................................................................................................... 5
5. Menu Structure and Operating the Device................................................................................. 5
5.1 Inputs Menu ...................................................................................................................... 6
5.1.1 Status Menu............................................................................................................ 6
5.1.2 DVB-S2 Menu......................................................................................................... 6
5.1.3 RSSI........................................................................................................................ 7
5.1.4 Ethernet Menu........................................................................................................ 7
5.2 Outputs Menu.................................................................................................................... 8
5.2.1 BISS Menu.............................................................................................................. 8
5.2.2 CI Menu .................................................................................................................. 8
5.2.3 Decoder .................................................................................................................. 9
5.2.4 ASI1...................................................................................................................... 11
5.2.5 ASI2...................................................................................................................... 11
5.2.6 SDI........................................................................................................................ 11
5.2.7 Mux ....................................................................................................................... 11
5.2.8 Ethernet ................................................................................................................ 12
5.3 System Menu.................................................................................................................. 15
5.3.1 Local Setup........................................................................................................... 15
5.3.2 Trap IP Addr.......................................................................................................... 15
5.3.3 Unit Name............................................................................................................. 15
5.3.4 Properties.............................................................................................................. 15
5.3.5 Factory Setting...................................................................................................... 16
5.3.6 Optional Function.................................................................................................. 16
5.3.7 LCD Switch........................................................................................................... 16
5.3.8 Machine Type ....................................................................................................... 16
5.3.9 HTTP Login........................................................................................................... 16
5.4 Ethernet Menu................................................................................................................. 17
5.4.1 IP Out.................................................................................................................... 17
5.4.2 IP In....................................................................................................................... 18

5.4.3 Local IP setting..................................................................................................... 19
5.4.4 Ethernet status...................................................................................................... 19
6. FAQ .......................................................................................................................................... 19
7. Specification............................................................................................................................. 19
8. Accessory List .......................................................................................................................... 21
9. IPTV Configuration Quick Guide.............................................................................................. 22
9.1 How to receive a multicast or unicast stream................................................................. 22
9.2 How to set the Unicast/Multicast output.......................................................................... 23

1. Before Use the Device
Thank you for purchasing the 6PSDSC-IP-5000Pseries.
This User Manual is written for operators/users of the 6PSDSC-IP-5000PMulti-Format
Professional HDTV Processor to assist in installation and operation. Please read this user
manual carefully before installation and use of the device
For Your Safety
This equipment is provided with a protective earthing ground incorporated in the power
cord. The main plug shall only be inserted in a socket outlet provided with a protective earth
contact. Any interruption of the protective conductor, inside or outside the device, is likely to
make the device dangerous.
Do not remove the covers of this equipment. Hazardous voltages are present within this
equipment and may be exposed if the covers are removed. Only NETKLA trained and
approved service engineers are permitted to service this equipment.
No operator serviceable parts inside. Refer servicing to NETKLA trained and approved
service engineers.
For the correct and safe use of the device, it is essential that both operating and
servicing personnel follow generally accepted safety procedures in addition to the safety
precautions specified in this manual.
Whenever it is likely that safety protection is impaired, the device must be made
in-operative and secured against unintended operation. The appropriate servicing authority
must be informed. For example, safety is likely to be impaired if the device fails to perform the
intended measurements or shows visible damage.
WARNINGS
The mounting environment should be relatively dust free, free of excessive vibration and
the ambient temperature between 0 ℃to 40 ℃. Relative humidity of 20% to 80%
(non-condensed) is recommended.
Avoid direct contact with water.
Never place the equipment in direct sunlight.
The outside of the equipment may be cleaned using a lightly dampened cloth. Do not
use any cleaning liquids containing alcohol, methylated spirit or ammonia etc.
For continued protection against fire hazard, replace line fused only with same type.
Air intake for cooling is achieved via holes at the side of the device and the fans inside.
The air flow should not be obstructed. Therefore, the device has to be placed on a flat
surface, leaving some space at the sides of the device.
When in operation, the internal temperature should not exceed the limit of 70 ℃.

2. Introduction
As the latest version of NETKLA‟s flagship professional IRD, the 6PSDSC-IP-5000Pis
full compliant with MPEG-2 (MP@ ML& MP@HL), H.264 and DVB-S2/S/-C/-T standards.
With a wide choice of input options for all transmission mediums, the
6PSDSC-IP-5000Pprovides significant benefits and the maximum flexibility for professionals
who wish to migrate their operations from MPEG-2 SD to H.264 HD. Equipped with 2
PCMCIA slots, it also supports various CA systems such as Irdeto, Conax, Viaccess,
Cryptoworks, Mediaguard, and SECA, etc.
With TS over IP output (Optional), user could convert DVB-S2/S/-C/-T programs into IP
format. It can be monitored and set parameters easily with Ethernet management software.
Moreover, it supports CVBS, YPbPr, BNC, SDI, HDMI, AES_EBU output interface. High
transmission speed and low error rate give more valuable features to this model. With 19”
rack, makes the receiver the best choice for your digital Headend System.
Model List
Model
No.
Function
x =
5000P-10x
5000P-20x
-5000P-30x
5000P-44x
C
T
S2
DS3
C
T
S2
DS3
C
T
S2
DS3
C
T
S2
DS3
10/100M Base-T
TSoIP
Input/output
√
√
√
√
√
√
√
√
GbE
Input/output
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
DVB-C Input
√
√
√
√
DVB-T Input
√
√
√
√
DVB-S2 Input
√
√
√
√
DS3 Input
√
√
√
√
CI slots*2
√
√
√
√
ASI TS
Input/Output
√
√
√
√
HD-SDI Output
（Embedded
Audio 2.0ch *2）
√
√
RCA Analog
Audio output * 2
pairs
√
√
√
√
Balance Analog
Audio output * 2
pairs
√
√
√
√
AES/EBU Digital
Audio Output *2
ports
√
√
YPbPr Output
√
√
√
√
HDMI Output
√
√
Ethernet
Remote Control
√
√
√
√
○: Optional √: Standard

Video Format
Output port
Resolution
SDI port
576I25 ,480I29.97, 1080I25, 1080I29.97, 1080I30
HDMI port
576I25 ,480I29.97,480P60, 576P50, 720P50,720P59.94 720P60,1080I25, 1080I29.97,
1080I30
YPbPr port
576I25 ,480i29.97,480P60, 576P50, 720P50,720P59.94 720P60,1080I25, 1080I29.97,
1080I30
CVBS port
576I25,480I29.97
3. Installation
3.1 Inspection
Open the packaging box, check if all appendixes are in the box according to the
appendix list, and if the device has any visible damage, please contact the agent.
3.2 Operating Voltage
Do not connect AC power until you have verified that the line voltage is correct and the
proper fuses are installed. The device‟s power supply is fitted with a wide-ranging power
supply. It is suitable for supply voltages of 100-240 Vac -10% +6% at 50/60 Hz nominal. Be
sure the supply voltage is within the specified range.
POWER REQUIREMENT
Input voltage
90-250 Vrms auto select
Frequency
47 to 63 Hz
Power
50 VA max. / 30 VA typical.
Current
110 V/0.27A or 240 V/0.125A typical
3.3 The fuses
The recognized recommended fuses are size 5 by 20 mm, rate T 2.0A, 250 V (UL and
IEC approved).
The line fuse is housed in a small container besides the power connector on the rear
panel. To check the fuse, insert the tip of a screwdriver in the slot at the middle of the
container and pry gently to extend the fuse where there is a little tap and pull out the fuse
gently. The fuse is attached to the line module and cannot be removed.
3.4 Connecting Up the Device
Always use the specified cables supplied for signal integrity and compliance with EMC
requirements.
The rear panel is directly related to the input and output options fitted. Below figure
shows a typical rear panel.

TS/IP IP input/output port
RS-232 serial port for printing information
ASI OUT1 Group1 ASI output port (one for back-up)
ASI1 IN ASI1 input port
SDI1 SDI1 output port
CVBS CVBS BNC output port
YPbPr YPbPr output port
L-Audio-R1 Group1 RCA audio output port
Audio1 AES/EBU and Balance Audio output port1 (need to
use the RS232-to-XRL converting cable in
accessories)
TUNER OUT Tuner signal loop through output port
TUNER IN Tuner signal input
Switch Power switch
MANAGEMENT LAN port for software update
ASI OUT2 Group2 ASI output port (one for back-up)
ASI2 IN ASI2 input port
SDI2 SDI2 output port
HDMI HDMI output port
CVBS CVBS RCA output port
L-Audio-R2 Group2 RCA audio output port
AUDIO2 AES/EBU and Balance Audio output port2 (need to
use the RS232-to-XRL converting cable in
accessories)
GND Grounding terminal
Power Socket AC 90~250V 50-60Hz input
3.5 Power On the Device
Be sure the device is mounted into the rack properly and firmly, and the signal cables
TS/IP RS-232 ASI Out1 ASI1 In SDI1 CVBS YPbPr L-Audio-R1 Audio1 Tuner out Tuner in Switch
Management ASI Out2 ASI2 In SDI2 HDMI CVBS L-Audio-R2 Audio2 GND Power Socket

are connected well, then power can be applied to the device. The main socket and fuse are
located at the rear panel of the device.
When the device is powered on, verify that the display shows the following message:
Digital TV Processor (factory default unit-name)
IP: 10.10.60.148 (factory default IP Address for LAN access)
If no message is shown in the display or there is not light in the display, the device is
defective and has to be returned for servicing.
4. Navigating the Front Panel
POWER Power indicator, green light means power is OK
TUNER LOCK Tuner lock indicator, green light means signal is locked; if
there is no light, which means no signal input or wrong
parameters setting.
ALARM Alarm indicator
LCD 2 × 20 character LCD
Operation buttons 〔 〕〔 〕〔 〕〔 〕〔ENTER〕〔EXIT〕buttons
〔〕〔 〕are used to up/down pages of menu or
increase/decrease value when edit numbers
〔 〕〔 〕 are used to move cursor
〔ENTER〕is used to enter sub menu or confirm operation
〔EXIT〕is used to return previous menu or cancel operation
Common Interface PCMCIA Module slot
5. Menu Structure and Operating the Device
The menu structure of the device is showed in below figure. After initialization is completed,
press 〔ENTER〕button to enter main menu:
Main Menu
Inputs
Outputs
Ethernet
System

(1) Input Setup Set input parameters
(2) Output Setup Set output parameters
(3) System Set system parameters
(4) Ethernet(optional) Set Ethernet parameters
Note: Ethernet under Main Menu only appears if the unit is a Gigabit model.
5.1 Inputs Menu
There are four options: Status, DVB-S2, RSSI and Ethernet (optional):
Note: Ethernet under Inputs Menu only appears if the unit is a Megabit model.
5.1.1 Status Menu
It contains four options, ASI1, ASI2, TUNER and IP IN, to show the status of signal
input:
ASI1: When signal from ASI1 input port is locked, it will display package format and
code rate; if signal is not locked, it will show Unlock.
ASI2: When signal from ASI2 input port is locked, it will display package format and
code rate; if signal is not locked, it will show Unlock.
TUNER: When signal from tuner input port is locked, it will display package format and
code rate; if signal is not locked, it will show Unlock.
IP IN: When signal from IP input port is locked, it will display package format and code
rate; if signal is not locked, it will show Unlock.(Note: this option only appears when set the
External Function as “IP IN”. Please refer to section 5.3.6 for setting method)
5.1.2 DVB-S2 Menu
There are 6 options to set DVB-S2 parameters. After signal is locked, the TUNER
Inputs
Status
DVB-S2
Ethernet
RSSI