Wirquin ONE User manual

Code
Issue No.
Date
240728
1
Mar/2018
MECHANISM WIRQUIN ONE MECHANICAL FLUSH VALVE
ASSEMBLY INSTRUCTIONS
▼

Description
Flush Valve Bridge
Flush Valve Body
Base
Sealing Washer
Backnut
Close Coupling Washer
Chrome Push Button
Close Coupling Bolted Kit
1

Flushing Valve
1 - Unscrew push button from bridge of flushing valve and pull up and remove.
2 - Remove bridge from flushing valve body (simply push the lugs in and pull up).
3 - Unclip flush valve body from flush valve base.
2

Fitting base and bolted close coupled kit
4 - Remove cistern from wall and pan.
5 - Replace the bolted close coupling kit (item H).
6 - Fit sealing washer (item D) onto base (item C) - sealing washer
to be fitted on inside of cistern.
7 - Fit the backnut (item E) handtight and 1/4 turn with suitable
spanner.
8 - Fit close coupling washer (item F) to threaded tail of base.
9 - Fit cistern.
Please Note: make sure that the cistern is drained of water before
removing and water supply is turned off.
3

10 - Clip flush valve body to base.
(Simply clip in and turn to lock in place)
Fitting flush valve body to base
4

11.1 - Turn the internal overflow to unlock.
11.2 - Set he internal overflow 20mm above the waterline inside
the cistern.
11.3 - Turn and lock the internal overflow in place.
Please Note: the internal overflow must be set 20mm above the
waterline inside the cistern.
Setting overflow height
5

12 - Clip the bridge back onto the flush valve body and leave
above the cistern body.
13 - Put the cistern lid on top of the bridge and gently push down
until the lid is located on the cistern body.
Your flush valve is automatically adjusted.
Setting the height of the flush valve bridge
6

14 - Fit the push button into the cistern lid hole making sure the rod
is located into the push button rod locator on the internal over
flow tube.
Warning: if the rod is not located in the push button rod locator
the flushing valve will not operate.
15 - Screw the push button onto the flushing valve.
Fitting push button
Push button rod
locating hole
7

16 - Turn water supply back on and fill the cistern.
17 - Firmly press the full flush push button all the way down
and release, this will activate the full flush. Repeat for part flush.
Please note the full ush cycle works on the release of the
push button
18 - The flushing valve is now automatically adjusted and ready
for use.
IMPORTANT
Priming the flushing valve
8

If you want to increase or reduce the full or part flush volumes then
remove the push button and cistern lid.
Unclip the flushing valve and set to the required flush setting.
Once this has been completed please start from Instruction 12 up
to 18 again.
Full and part flush volumes
Up for less water,
down for more water
Full flush adjustment
Part flush adjustment
Please note slide C on the side of the flushing valve must
always be set at 2
Up for less water,
down for more water
9

Use only soapy or clean water
Trouble shooting
Removing flushing valve sealing washer
Do not use
10
Problem
It does not flush
Solution
Check that the push button rod is located into the
push button rod locator on the internal overflow
tube (see page 7).
Check that you have primed the system.

WIRQUIN Ltd.
Warmsworth Halt Industrial Estate, Warmsworth, Doncaster DN4 9LS, United Kingdom
Technical and Sales enquiries: 0044 (0) 333 222 4488
Email: [email protected] www.macdee-wirquin.co.uk
WIRQUIN FLUSHING LVE RANGE
►MECHANICAL ► PNEUMIC
WIRQUIN ONE

WIRQUINONE
)
KLA

10120440
' ,
n
►CABLE
lj
l
lr
•
QUICK FIT

5017134134247
-
JOLTRONIC JOLLVFLUSH
 

Box 1/
8 /240
mae
--
WIRqu,n
Watch our
INSTALLATION
Video