Wisenet BabyView EcoFlex SEW-3048W User manual

English · 2
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Unplug this apparatus during lighting storms or when unused for long periods of
time.
13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Copyright
©2017 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in
this manual are the registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced,
distributed or changed, partially or wholly, without formal authorization.
Disclaimer
Hanwha Techwin
makes the best to verify the integrity and correctness of the contents in this
document, but no formal guarantee shall be provided. Use of this document and the subsequent
results shall be entirely on the user’s own responsibility.
Hanwha Techwin
reserves the right to
change the contents of this document without prior notice.
BabyView eco FLEX
User Manual
CAUTION
• Risk of explosion if battery is replaced by an incorrect type.
• Immediately discontinue use of the product if the battery or battery door is swollen or bulging
which may be a precursor to overheating batteries.
• It is good practice to periodically remove the battery door at the back of the monitor to check
if the battery has any signs of deformations.
• Do not let a loose battery come in contact with metal objects such as coins, keys or
jewellery.
• Dispose of used batteries according to the instructions.
• If the battery is not fully charged after 7 hours, stop charging immediately. Overcharging may
cause fire, burns or injuries.
• Please use the product in a room-temperature environment. The usage of the monitor in
extremely high temperature or low temperature will shorten the lifespan of the battery. (ex.
Leaving the product in a closed automobile during summer will affect the battery lifespan).
• This battery is expendable. If you noticed the battery has stopped charging or that the
battery’s usage time has shortened drastically, stop using the product immediately.

English · 3
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada Statement
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Ce dispositif est conforme à la norme RSS-247 d’Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout
brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
Industry Canada Radiation Exposure Statement (Déclaration d’exposition aux
radiations )
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non con trôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.
WARNING
• STRANGULATION HAZARD - Keep cord out of child's reach. NEVER place camera or cords
within 3 feet of crib or playpen. Never use extension cords with AC Adapters. Only use the
AC Adapters provided.
• Some adult assembly or installation required.
• This product contains small parts that may cause choking. Keep small parts away from
children.
• This product is NOT intended to replace proper supervision of children. You MUST check
your child’s activity regularly, as this product will not alert parents to silent activities of a child.
• Before using this product, read and follow all instructions contained in this booklet, and read
and follow all instructions and warnings on the product.
• NEVER use the transmitter or monitor near water, including near a bathtub, sink, laundry tub,
wet basement, etc.
• This product is intended for indoor use only.
• This product is not intended for use as a medical monitor and its use should not replace
adult supervision.
• The transmitter detects normal sound levels within a range of 2 to 3 meters (6 to 10 feet)
from a child. If the child moves outside of this range, it may not be able to detect sounds
from him or her.
• It is essential that you check the operating range and condition of the transmitter monitor on
initial installation, and on a regular basis after that.
• Check reception regularly. Test monitor before use and after changing camera location.
• Do not take apart the product by yourself.
• To prevent overheating, keep the product and AC power adapters away from any direct
sunlight and heat sources such as radiators, heat registers, cooking devices (e.g., stoves
and ovens) and other appliances that produce heat (e.g., amplifiers, televisions and stereos).
• Ensure that the product is well ventilated during use. Avoid contact with pillows and furniture
that may block ventilation.
• Use only the AC adapters provided with the product, as other adapters may damage the
product. Plug the adapters only into standard household current (100~240 volts AC).
Place the AC adapters avoiding pinch points otherwise you can damage the adapters.
• When an AC adapter is plugged into a power source, DO NOT touch the exposed end of the
AC adapter’s cord.
• Do not use extension cords with the AC power adapters to avoid entanglement.
• This product should only be serviced by qualified and authorized Hanwha Techwin service
centers.
• Images and sounds are transmitted by the product over public airwaves and transmissions
may be picked up by other units. (Although the transmission distance is 328ft or longer, it
may vary depending on whether there are obstacles between the camera and the monitor.)
• Caution: If you use the system to watch a young child, do not place the camera where the
child can reach.
• When using the system with only battery power and the charge is low, then the picture and
or sound may affected.
• If this occurs then please connect the AC power adapter.
The transmission range of the wireless signal may weaken if heavy obstructions such as
a concrete, brick, or metal walls are between the camera and monitor, or if there are
several Wi-Fi routers and devices in your environment.
To avoid interference with 2.4Ghz RF signal, keep your wireless networks (Wi-Fi routers,
Bluetooth systems, or microwave ovens) at least 3ft (1.5m) away from the Camera and
Monitor.

English · 4
n
`Check the package to confirm that you have received all the components for the system as shown above.
`You must have more than one camera configured to the system when using functions that require more than one camera.
Wireless Camera Wireless Monitor User Manual / Warranty Card
Camera / Monitor Adapters
Plastic Anchor (2EA)
Screw (2EA)
Bracket Accessory
1. Antenna
2. Power On/Off
3. Sound Indicator LED
4. Lullaby Button
5. DC 5V Power Input
16. Battery
17. Temperature Sensor
18. Low Light Sensor
19. Lens
20. IR LEDs
21. Microphone (Camera)
22. Speaker
23. Power Slide Switch
24. DC 5V Power Input
25. Pair Button
26. Reset Button
27. Flexible Stand
6. Talk Button
7. Status LED
8. ECO LED
9. Mode Button
10. Microphone (Monitor)
11. Color TFT4.3" LCD
12. Direction Button
13. Menu / OK Button
14. Speaker
15. Kick Stand
1
2
3
4
5
6
7 8
9
10
11
12
13
14
15
16
17
22
23
24
18
19 25
26
27
20
21
Product Overview
What’s Included (Package Contents)

English · 5
Pairing Camera and Monitor
The units already come paired for your convenience.
The pair button is used to pair additional cameras. Users can assign
numbers to the cameras. Up to 4 cameras may be paired.
If you have additional camera, pair your camera as follow:
1. Power on the wireless monitor and new camera.
2. Press the "OK" button to make the settings icon appear on the screen.
3. Select [ ] icon.
4. Select the camera number in the pair/unpair channel list.
The monitor will search for the new camera when set to pairing mode.
A countdown clock will appear in the middle of the screen and will start
counting from 30 to 0.
5. Press the [PAIR] button located on the rear of the camera.
6. If the monitor successfully pairs with the camera within the 30 second
countdown period, the monitor will automatically switch to display the
view of the newly paired camera.
1. Fully charge the system before use. Connect the camera to the power
adapter. Plug the adaptor into an outlet. Camera must be plugged in at
all times.
2. Push the power button for about 2-3 seconds to turn on the monitor.
3. Turn the power switch to "On" to turn on the camera. A red LED
indicator will illuminate if it is turned on.
Powering Your System
Monitor Camera
PAIR
n`You can use the monitor while it is charging
.
`Full Charging Time for Monitor: 5 - 6 hours.
Fully charge the monitor's battery before initial use and recharge the monitor
as needed.
Getting Started

English · 6
m
a b c d e f g h i
k
j
l
n
o
p
q
r
s
t
No. Icon Name Description
aSignal
Indicator
Shows the signal strength between the
camera and monitor.
No bars indicate that the system is "Out of
Range".
bDigital Clock
Displays the time that is set on the monitor.
Time is displayed in 12-hr, AM/PM format
only. There is no 24-hr format option.
cCamera
Number
Indicates the camera currently being
displayed on the monitor screen.
dFlipped
image
Indicates when the image is flipped vertically.
eLullaby
Indicates when a lullaby is playing.
f
Vox Mode Indicates when the camera is in VOX
Mode.
Eco Mode Indicates when the camera is in Eco
Mode.
Video Mode Indicates when Video Mode is On.
Audio Mode Indicates when Audio Mode is On.
gNight Vision Indicates when Night Vision is On.
hZoom Mode
Indicates Zoom Mode is on.
Zoom Level: x1/ x2
The camera(s) will zoom in and out
sequentially when you press and hold the
"OK" button.
iAudio Muted Indicates the monitor's speaker is muted.
jBattery
Power Level
Fully Charged
Charging
(When the battery is charging, the 2 icons
above will show alternately.)
Low Battery
kTwo-Way Talk
Press and hold the talk button while
talking.
Two-Way Talk icon will appear on the
screen when the button is pressed down.
lTemperature
Display Temperature Units: Fahrenheit/Celsius.
mFeed Timer
Display Displays reminders for baby's feeding time.
User Interface Description

English · 7
Button Description
Function Description
VOX (Voice activated)
Select to monitor and listen for significant sound levels with reduced
ambient noise.
The monitor screen goes off in "VOX" mode after 30 seconds if there is no
detection of significant sounds louder than the minimum noise level, but
turns back on as soon as it detects sound that exceeds the minimum noise
level.
You can set the sensitivity level in "VOX" mode.
• 'Low' Sound Level Detection : Sets to higher sensitivity.
• 'High' Sound Level Detection : Sets to lower sensitivity.
ECO Mode
In the energy-saving ECO mode, the screen goes off after 30 seconds if
there is no detection of significant sounds louder than the minimum noise
level. The monitor will not deliver any detected background sounds once
the camera goes into this power saving mode, which helps decrease the
RF radiation levels in the baby's environment. The monitor screen turns
back on as soon as the camera detects sound exceeding the minimum
noise level.
Video Mode
The screen is always in "Video" mode for continuous video and audio
monitoring.
Audio Mode
The screen will turn off in "Audio" mode to only capture sounds around the
camera(s) surrounding. The screen will turn back on by pressing any button
on the monitor.
No Signal Warnings
An "Out of Range" message will appear when the baby monitor is out of the
camera's range.
To improve the wireless signal strength, reposition the camera and/or the
monitor closer to each other, or check the camera's power connection.
Sequence View
Select View Menu to enter into Sequence View. The sequence will start at
Cam 1, then automatically switch to the next camera, Cam 2, after
10-seconds. When enabled, "Sequence View" will continue to change
between cameras. To see details from a particular camera's view, just press
the "OK" button to display the camera's view in full screen.
Monitor
`Mode button: Press to change between modes (VOX - ECO - VIDEO - AUDIO).
Mode Selection: select the desired mode, then the monitor will switch to the
chosen mode.
`Power button: 1) Press and hold down for 2-3 seconds to turn ON/OFF the
monitor. 2) When in On-Screen Display (OSD) mode, press the power button
briefly to return to the previous interface.
`Lullaby button: Shows a list of Lullabies (#1-4: Lullabies, #5-7 White Noise,
ALL: all Lullabies from #1-4).
1) Select a lullaby from the list to play and press "OK". 2) Press "OK" again
to stop playing the lullaby, and press the "Lullaby" button to exit out of the
lullaby list.
`Talk button: Press and hold button to speak.
`OK button: 1) Press to display menu or confirm selection. 2) When in View
Mode, the camera will zoom in and out sequentially each time you press and
hold the "OK" button.
`Direction button: The multi-directional keypad serves two purposes. 1) Menu
Selection: Press the OK button to access the menu then use the multi-
directional keypad to select an option. Press the OK button again once you
have made a selection. 2) Camera Control: When in viewing mode, press
the left or right arrow on the keypad to pan around the room or up or down
to tilt and adjust the camera angle (applicable model: SEP-102CRW).
Camera
`Reset button : Press the reset button for at least 3 seconds to reset the
camera.
`Power switch: Turn ON/OFF the camera.
`Pair button: Pair camera(s) to monitor.
No. Icon Name Description
nView Mode Select camera(s) to view and the viewing
mode.
o
Brightness
/ Volume
Adjustment
Adjust monitor brighness level: 1~5.
Adjust monitor volume level: mute, 1~7.
Adjust camera volume level: 1~5.
pTemperature Temperature display On/OFF, and set
temperature.
qVOX/ECO
Sensitivity
Adjust VOX/ECO Sensitivity Level: Low or
high sensitivity.
rFeed Timer
Turn ON/OFF to display the baby feed
timer.
Set baby's feeding schedule.
sPairing Pair/Unpair 1-4 Cameras.
tSystem Menu Set time and flip mode, or reset the
monitor to factory settings.

English · 8
CAUTION: If you are using this system to watch a young child, please do
not place the camera within the child's reach.
Wireless Monitor
1. Place the monitor in an area that provides clear reception to your
camera(s).
2. Pull out the stand.
n
`Do not pull out the monitor stand with excessive
force.
Wireless Camera
Before you install the camera, carefully plan where and how it will be
positioned, and where you will route the cable that connects the
camera to the power adapter.
Before starting permanent installation, verify its performance by
observing the image on the monitor when camera is positioned in the
same location/position where it will be permanently installed and the
monitor is placed in the location where it will be used most of the time.
Installation Warnings
Aim the camera(s) to best optimize the viewing area: Select a location
for the camera that provides a clear view of the area you want to
monitor, which is free from dust, and is not in line-of-sight to a strong
light source or direct sunlight.
Avoid installing the camera where there are thick walls or obstructions
between the camera and the monitor.
STRANGULATION HAZARD - Keep cord out of child's reach. NEVER
place camera or cords within 3 feet of crib or playpen. Never use
extension cords with AC Adapters. Only use the AC Adapters
provided.
n
`On the bottom part of the camera there is a dot marked that shows the
detachable part.
How to install

English · 9
Problem Solution
No picture from a
camera
1. Check all connections to the camera. Make sure the adapter
is plugged in.
2. Make sure that the cameras and monitor are both ON.
3. Make sure that the camera is in range of the monitor.
4. Make sure the camera and monitor are paired.
5. Adjust the monitor antenna to a vertical position.
The picture is or has
become choppy
The picture may become choppy when experiencing a lower
frame rate
(i.e. 10 frames per second vs. a higher 20 frames per second).
1. Try moving the camera closer to the monitor.
2. Remove obstructions between the monitor and camera.
3. Adjust the monitor antenna to a vertical position.
No sounds (even
with both units
turned on)
1. Make sure that the power adapter is connected to the
camera.
2. The battery on the monitor may be dead, be sure to charge it
using the adapter included.
3. The monitor may be out of range from the camera.
Your BabyView Eco
FLEX is emitting an
high pitched noise/
feedback.
This sound is normal feedback which occurs if the monitor and
camera are too close together. Move the units apart and the
monitor will not emit high pitched noise/feedback.
Monitor screen is
frozen.
Restart your monitor and check the connection to the camera.
If the baby monitor displays the "Out of Range" message, move
the monitor closer to the camera.
n
`Low battery will cause the supply current to become unstable and will affect
the quality of the video/audio. Please charge the battery fully for superior video.
Trouble Shooting Product Specifications
Item Details
System General
Operating Frequency Range 2400 MHz~2483.5 MHz
Type of Spread Spectrum TX FHSS
Type of Modulation GFSK
Number of Camera Support Up to 4 cameras
Data Rate 4Mbps
Transmission range Up to 900ft (line of sight, no obstruction)
Regulation Compliance FCC/CE(RoHS)
Operating Environment 32oF~+104oF / 85% RH / Indoor use only
Wireless Camera
Image Sensor Type 1/4” Color CMOS Image Sensor
Effective Pixel 640x480 (VGA)
Image Compression MJPEG
Lens EFL=3.95mm, F=2.2
(Viewing Angle (D): 55degree)
Night Vision 16 ft. (5m) in the dark with 8 non-visible IR LEDs
White Balance Auto
Lullabies 4 songs + 3 white noises (Remote On / Off)
Temperature sensor Yes (+/-2 degree)
Power Requirement DC 5V ±10%
Power Consumption 2.5Watt (max)
VOX level detection Low: 50dBA / High: 65dBA
Audio Built in Microphone/ Speaker
Wireless Monitor
Display Information 4.3" 480x272 Color TFT
Digital Zoom X1 , X2
Real Time Clock (RTC) +/- 5sec / day
Power Requirement Adapter : DC 5V ± 10%, Battery : 3.85V Li-ion
Power Consumption
4.0Watt (max)
Audio Built in Microphone / Speaker
Rechargeable Battery 2100mAh Li-ion Polymer
Battery time duration Monitor On: max. 5.5 hours / Audio Only: max. 10 hours

English · 10
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection
systems)
This marking on the product, accessories or literature indicates that the product and
its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of
with other household waste at the end of their working life. To prevent possible harm
to the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take these items
for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with
other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery
return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this
product should not be disposed of with other household waste at the end of their working
life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries
are not properly disposed of, these substances can cause harm to human health or the
environment.
To protect natural resources and to promote material reuse, please separate batteries from
other types of waste and recycle them through your local, free battery return system.
Hanwha Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.

English · 11
MEMO