Wisenet SHD-3000F5 User manual

In-Ceiling Plenum Housing
Installation Manual
SHD-3000F5

2_ SHD-3000F5
Overview...............................................................................................................................................................3
What’s Included...................................................................................................................................................3
Installation Instructions ....................................................................................................................................4
How to install.......................................................................................................................................................4
Product Specifications................................................................................................................................... 10
TABLE OF CONTENTS

SHD-3000F5 _3
OVERVIEW
This In-CEILING HOUSING is a mounting ADAPTOR that is designed to mount PNM-9000VQ
in built-in style on a double-layer ceiling. The housing is Plenum rated when properly
installed.
WHAT’S INCLUDED
HOUSING SAFETY BRACKET ( 1EA) SAFETY WIRE (1SET)
In-ceiling Housing
Installation Manual
SHD-3000F5
TEMPLATE (1EA) INSTALLATION MANUAL

4_ SHD-3000F5
INSTALLATION INSTRUCTIONS
1. Select an installation position or place that can endure more than 4 times of the total weight
of the installation structure.
2. At least 250mm or more of spare height is required above the CEILING BOARD.
3. CEILING BOARD’s thickness should be less than 50mm.
4. Be sure to secure the SAFETY WIRE to avoid a product fall.
5. If you want to attach the camera to the ADAPTOR, use the only provided SCREWS.
(SCREWS are shipped with PNM-9000VQ. To learn how to use them, see Step 3 on page 5.)
6. CEILING BOARD must be able to sustain the weight of at least 10 kg.
More than 250mm
CEILING BOARD More than 5mm,
Less than 50mm
HOW TO INSTALL
1. Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
❶ Remove the round lling (“C”) from the TEMPLATE.
➋ Place TEMPLATE A onto the CEILING BOARD to which you will attach the ceiling mount
ADAPTOR and drill a hole of Ø326mm in diameter.
See the gure below for the hole shape.
TEMPLATE
CEILING BOARD

SHD-3000F5 _5
2. Remove the CAP and NUT that t to the size of the HOLE you are going to use.
3. Remove the Dome Cover and Mounting Plate according to the Disassembling section in the
PNM-9000VQ manual.
4. Join the MOUNTING PLATE to the Housing using the SCREWS shipped with PNM-9000VQ.
SCREW
MOUNTING PLATE

6_ SHD-3000F5
5. Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the
ANCHOR BOLT as below:
❶ Tighten the NUT (“N1”) on the ANCHOR BOLT.
➋ Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
➌ Tighten two NUTs (“N2”
,”N3”) onto the ANCHOR BOLT.
➍ Hook and x one end of the SAFETY WIRE onto the SAFETY BRACKET.
➎ Hook and x the other end of SAFETY WIRE onto the HOUSING as shown below:
ANCHOR BOLT
Nut (N1)
Safety BRACKET
Nut (N2,N3)
SAFETY WIRE
ANCHOR BOLT
HOUSING
CEILING
CEILING
M

The ANCHOR BOLTs and nuts are not included in the product package.
ANCHOR BOLTS must be able to sustain the weight of at least 30 kg.

If you proceed without following the instructions in the manual, that is if you work with the
camera body already attached from the beginning, the safety wire could exceed its limit
and be broken if the housing is accidentally dropped, which could result in an accident.
➏ After xing the SAFETY WIRE to the HOUSING, tighten the screw in the SAFETY RING to the end.
6.
In the case that apipe is to be connected to the External Cable hole, the pipe must be
inserted within the depth of 15mm or less.
Less than 15mm

SHD-3000F5 _7
7. To connect to the camera, insert the external cable through the Cable hole on the housing to
the inside of the housing as shown in the gure.
M
Refer to the installation manual of the camera that you want to install, and prepare necessary
cables for camera connection.
External Cable
CEILING
SAFETY WIRE JOINT
HOUSING
External Cable hole
HOUSING
SAFETY WIRE
8. Push the HOUSING inside the CEILING through the CEILING hole, and tighten the SCREWs (x2)
clockwise to x the HOUSING on the CEILING.
(The BRACKET will be positioned from <A> to <B> as shown.)
M
Ensure that the HOUSING is firmly secured to the CEILING BOARD.
BRACKET BRACKET
SCREW Turn clockwise
HOUSING
SAFETY WIRE
<A> <B>
BRACKET
BRACKET

8_ SHD-3000F5
9. Proceed with the rest of the installation process for PNM-9000VQ according to the sections
next to Disassembling in the PNM-9000VQ manual.
HOUSING
Cover
10.
Align and attach the COVER to the HOUSING following the arrow, and push it hard so that
four Hook & Loop Fasteners are firmly attached to it.
Hook & Loop Fasteners

SHD-3000F5 _9
11.
When all Hook & Loop Fasteners are attached, tighten the four SCREWS on the
COVER to fix it to the HOUSING.
M

Since Hook & Loop Fasteners are lightly attached to the surface, they can easily be
detached. Therefore, the screws need to be tightened immediately after attaching
the Hook & Loop Fasteners.

10_ SHD-3000F5
PRODUCT SPECIFICATIONS
Item Specications
Dimension (mm) Ø352 X H109
Weight
2550g (5.62 lbs)
Temperature
-10°C ~ 55°C (14°F ~ 131°F)
Material
Aluminum, Plenum rated
Color White (Cover)
Unit : mm (Inches)

MEMO

PT01-005359A
Head Oce
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : [phone] Fax : [phone]
www.hanwha-security.com
Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax [phone]
www.hanwhasecurity.com
Hanwha Techwin Europe
Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel [phone] Fax [phone]
www.hanwha-security.eu