Witek System MIS-200BE User manual

1
W
ITEK
SYSTEM
INC
MIS-200BE
INTRALOT
Scanner
User’s Guide

2
NOTICE
1. Witek System Inc. reserves the right to make changes to the contents of
this publication without prior notice.
2 Witek System Inc. reserves the right to make changes to equipment
and specifications without obligation or notification.
3 Some equipment nomenclature and abbreviations used here may
differ from that contained in other Witek publications
4 Witek System Inc. will not be held responsible for any accidents for
damage caused by procedures not in compliance with those in this
publication, or by actions that did not heed to the cautions.
5 This publication, or parts thereof, may not be reproduced in any
form without prior written permission of Witek System Inc.
Unauthorized use or distribution of this publication is prohibited.
(c) Witek System Inc. 2009
Information to the user
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

3
Important safety Instructions
This manual describes important details for users to use this product safely and correctly.
Read this manual thoroughly before you start using this product. Be sure to read and fully
understand the Safety Precautions in this manual, in particular. In addition, keep this manual
handy during use of this product, so that you can refer to it quickly when necessary.
The following instructions pertain to the risk of fire, electric shock or bodily injury. Please
read all of these instructions carefully.
1 Save these instructions for later use.
2 Follow all of the instructions and warnings marked on this product or included in this
manual.
3 Do not use this scanner on an unstable cart, stand or table. The product may fall, causing
serious damage to the product.
4 Don’t use this product on a bed, sofa, rug or other similar surface. This product should
never be placed near or over a radiator or heat register.
5 Never push objects of any kind into the scanner through the case openings, as they may
touch dangerous voltage points or short out parts that could result in a fire or electrical
shock. Never spill liquid of any kind on the product.
6 This scanner should only be connected to the + 24V / min. 2.5A DC power source or
designated power adapter indicated on your scanner information label. If you are not
sure of the type of power source available, consult your dealer or local power company.
Only connect this scanner to a power outlet that matches the power requirements of this
scanner.
7 Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8 Do not use this scanner near water.
9. Do not touch the power plug or USB bus power cable with wet hands. Doing so might
cause electric shock.
10. A damaged power cable or USB bus power cable may cause fire or electric shock. Do
not place heavy objects on the power or USB bus power cable, or pull, bend, twist, heat,
damage or modify the cable. Do not use damaged power or USB bus power cables or
power plugs. Do not use the power cable when the wall socket is loose.
11. Use only the specified Power, USB bus power, and interface cables. Failure to use the
correct cables might cause electric shock and equipment failure.

4
12. If you detect heat coming from the device or detect other problems such as smoke,
strange smells or noises, immediately turn off the scanner and then disconnect its power
plug from the power outlet, or unplug the USB bus power cable from the computer.
Make sure that the smoking has stopped, and then contact an authorized Witek scanner
service provider.
13. Do not place heavy objects on the scanner or use the top surface of the scanner for
performing other work. Improper installation might cause injuries.
14. When the scanner is not used for a long period, be sure to disconnect the power plug
from the power outlet, or disconnect the USB bus power cable from the computer for
safety. Not doing so might cause electric shock or fire.
15. Do not insert or drop metal or flammable foreign objects in to the scanner.
Do not scan wet documents or documents with paper clips or staples.
Do not splash or allow the scanner to get wet.
16. To avoid injuries, do not place the scanner in an area where small children may be able
to reach.
17. Do not move the scanner with the power and interface cables connected as this might
damage the cables, causing fire, electric shock or injuries. Before moving the scanner, be
sure to disconnect the power plug from the power outlet, and disconnect interface cables
as well. Also, make sure that the floor is free of obstructions.
18. Avoid getting a sleeve, necktie, or hair caught up in any scanner mechanism when
scanning as this may cause injuries.
19. Install the scanner away from strong magnetic fields and other sources of electronic
noise. Also, protect the scanner from static electricity as this might cause the scanner to
malfunction.
20. Do not use the scanner immediately after moving it from a cold place into a warm room.
This may cause condensation, which might lead to scanning errors. Let the device dry
about one or two hours before you use it.

5
Maintenance
Repairs should be done by properly trained repair technicians. When this product needs
servicing, please contact the authorized Witek Image Scanner service provider.
If the product does not operate normally, adjust only those controls that are covered by the
operating instructions. Improper adjustment of other controls may result in damage and may
require extensive repair work to restore the product to normal operation.
Unplug this product from the main power outlet and call for service under any of the
following conditions:
a If the power cord or plug is damaged or frayed.
b If liquid has been spilled into the product.
c If the product has been exposed to rain or water.
d If the product has been dropped.
e If the product exhibits a distinct change in performance, indicating a need for service.
Stop
If you ever have to remove the scanner cover, observe the following precautions :
a The power supply cord must be unplugged before the scanner cover is removed.
b Once removed, the cover must be replaced and screwed in position before the power
supply cord is plugged back in.

6
CONTENTS
1. Before you start using the scanner
1.1 Unpacking
1.2 Part Identifications
1.3 Connecting the Cables
1.4 Driver Installation
2. Installation Specifications
3. Using the scanner
3.1 Basic Flow of Operations
4. Troubleshooting
4.1 Clearing Paper Jams
4.2 Troubleshooting check list
5. Cleaning the inside of the Scanner
6. Dimension
7. Repair

7
1
1. Before you start using the scanner
1.1 Unpacking
When you unpack the scanner package, find the packaging list first, and then make sure that
the MIS-200BE and all items in the packaging list are present. If anything is missing or
damaged, contact the dealer where you purchased the product.
1.2 Part Identifications
This section describes the names of parts and their functions.
■ Front View
■ Rear View
Paper Entrance
load the documents to be scanned on
this part.
Jam Removal Open Cover
open the cover to remove paper jam
Paper Outlet
paper out
Paper Guide(ears)
adjust the paper width to scan
USB Connector
Power Connector
Power Switch

8
1
■ Use the following cables(Options)
The Power cable (Option) is a combination of
the AC adapter and AC cable.
USB bus power cable(Option)
* additional cable option : Power Y cable (compatible with microlot power source)
■ USB Interface
Pin Signal Descriptions
1 +5V +5V
2 Data - Scanner transmit data line
3 Data + Scanner transmit data line
4 GND System Ground
1 2
34

9
1
1.3 Connecting the cables
Connect the MIS-200BE scanner to a power supply in either of two ways below: First, connect
to a power supply, and then connect to a host terminal with the USB cable.
Be sure to use the supplied AC adapter and AC cable.
Be sure to use the supplied USB cable. The operation with any
commercially available USB cable is not guaranteed.
If only the USB cable is used, the MIS-200BE does not operate. Be
sure to use two types of cables, the power and USB cables, to
connect the MIS-200BE to a host terminal.
Connect the Power cable before connecting the USB cable
When connecting to a USB hub, be sure to use the first stage USB
hub that is closest to the computer. If you use the second or later
hub stages, the scanner may not operate properly.
When connecting with a USB 2.0 cable, make sure that the USB
port to connect to and hub must be USB 2.0-compliant.
Attention
Host
Terminal
USB port

10
1
1.4 Driver Installation
■ Before Installing the SDK & Driver for MIS-200BE
Before Installing the SDK & Driver for MIS-200BE, perform the following
preparations. :
1. Check your system
The system requirements for the MIS-200BE are as follows
One of the following operating system is required :
Windows 2000
Windows XP
Embedded XP
Linux
Host terminal
* For Windows 2000,Windows XP and Linux :
Recommended: Intel® Celeron® M 430 1.73 GHz or higher
Minimum: Intel® Pentium® III 600 MHz or higher
* USB port (USB 2.0/1.1)
RAM
* For Windows 2000 and Windows XP:
Recommended: 512 MB or more
Minimum: 256 MB or more
Free disk space
Minimum100 MB
2. Make sure that the MIS-200BE is not yet connected to your host terminal.
3. Start your computer.
Log on as a user with "Computer administrator" privileges.
4. Exit all programs and close all windows.

11
1
■ Installing the (“MIS-200BE _setup.exe”) and the Driver for MIS-200BE
These instructions are for Windows XP (which we highly recommend
with our USB Interfaces). Installation under Windows 2000 and
embedded XP are similar, but not necessarily identical. If you are using
Linux, then you should contact your dealer or Witek Technical team,
We may send you Linux driver.
SDK Installation
1. Make sure you have a “MIS-200BE _setup.exe” that dealer or Witek distributor
provided. If not, You may download “MIS-200BE _setup.exe” from Witek
website as www.witek.co.kr
2. Execute “MIS-200BE _setup.exe”.
3. Click the [Next >] button
4. The following dialog should appear;
Attention
You should select
typical and then click
“next” button
Execute

12
1
5. The following dialog should appear ;
6. Click the [Finish] button to complete the installation
After installation of MIS-200BE _setup.exe. You may find the
following folders under
C:\Witek\Driver
\ MIS-200BE \
\branding image
\firmware
\cfg
\program
You may execute MIS-200BE.exe in the ..\program folder.
Note

13
1
The Driver Installation
7. Plug MIS-200BE Scanner USB Interface to your host terminal USB port . A
message like this should appear on your terminal PC's Taskbar:
If the new Hardware Found Wizard popup does not appear when you
plug in your interface, go into Device Manager and look for the
interface. In Windows XP, you can typically find the Device Manager
by RIGHT-CLICKING on My Computer then selecting Manage.
Your Witek CIS SCANNER USB Interface should be under Universal
Serial Bus (USB) Controllers or under Other Devices. If it's there,
Right-Click it and then select Update Driver. Then you can start at
Step 3 in the instructions below.
8. The New Hardware Found Wizard should appear:
Attention
On the screen left, select "Install
from a list or specific
location (Advanced)"
then click the [Next >] button

14
1
9. The following dialog should appear:
10. On the screen above:
Select "Search for the best driver in these locations"
Check "Include this location in the search:"
Use the [Browse] button to find the MIS-200BE folder
(Usually C:\Program Files\ MIS-200BE \driver)
Click [OK]
11. The following dialog should appear:

15
1
12. Click the [Next >] button
13. The following dialog should appear:
14. This dialog warns you that we haven't paid Microsoft a pound of flesh to certify
the driver. You're going to have to click the [Continue Anyway] button..:-)
15. The following dialog should appear:
16. Click the [Finish] button to complete the installation

16
2. Installation Specifications
The following table summarizes the installation specifications of this scanner.
Scan Descriptions
Scan source Single sided Contact Image Sensing
Scan size Width: up to 104 mm(lottery application : 82.55 mm)
Length: up to 290 mm
Scanning Resolution 200 dpi
Scanning Speed Max. 400 mm/sec at B/W, 256 gray
Out put Format 1 bit (b/w), 4 bit (16 gray), 8 bit (256 gray)
Image format Bmp, jpg, tif and raw image data
Interface USB 2.0 & 1.1 (WINDOW, LINUX DRIVER SUPPORT)
Paper thickness 0.1 mm ~ 0.2 mm
Power +24 VDC/2.5 A or 2.7 A
MTBF 50,000 hours (CIS only)
Dimension 162 mm (W) x 110.5 mm (H) x 155 mm (D)
Weight 1.7 kg
Temperature / Humidity Temp.: -20 oC ~ 60 oC
Humidity: 10 % R.H. ~ 90 % R.H. non-condensing
Scanner SDK API Programming support(library files)
Linux/window available
Option
Thermal Brander
Dual CIS Sensor(Dual Scan)
Shade free Scan
Image processing Library
OMR Library
Barcode Recognition Library
UV Sensor light for counterfeit detection

17
3
3. Using the scanner
3.1 Basic flow of Operations
With the document, such as check, omr card, loaded on the MIS-200BE, simply insert the the
document, and you can save the scanned documents to files via your program using Witek
SDK or test program (MIS-200BE)
Make sure that the Power cable or USB bus power cable is connected to the
MIS-200BE scanner
Do not scan the following types of documents:
Document with paper clips and/or staples (Remove clips and staples to
scan these documents.)
Documents folded in half
Materials other than paper such as the fabric, metal foil, transparency, or
plastic card
Attention
Note

18
4
4. Troubleshooting
4.1 Clearing Paper Jams
If a paper jam occurs during scanning, follow the procedure below to remove the jammed
document.
1. Open the Jam removal cover
2. Remove the jammed paper in the scanner
3. Close the Jam removal cover
Jam Removal Open Cover

19
4
4.2 Troubleshooting check list
This section describes common problems that may occur during usage of the MIS-200BE
and how to solve the problems. Before you call a repair service, perform simple
troubleshooting steps in the table below. If performing these troubleshooting steps does not
resolve your problem, contact an authorized Witek scanner service provider or dealer.
Symptom Check this item Resolution
Correctly connect the power or
USB cable and USB bus power
cable to the computer. When
using a hub, check the hub’s
power supply. If you connect to
a non-powered hub, the scanner
may not work properly.
The scanner cannot
be turned on Are the power or USB bus power cable and the USB
cable connected correctly?
Disconnect and then re-connect
the power
Is the USB cable connected
correctly? Connect the USB cable correctly.
Scanning does not
start. Is the device driver installed
correctly? Re-install the MIS-200BE device driver
The document is
not fed properly or
gets jammed.
Is the inside of the scanner
dirty? Or, did you insert any
paper that is torn, or bent?
Clean the dirty locations. Do
not insert the paper that is torn
or bent
Black lines are
produced on the
scanned document.
Is the scanned document
written with a pencil? Black lines may be produced on scanned documents written with
a pencil, making the rollers
dirty or causing improper paper
feeding. To avoid such troubles,
clean rollers as often as
possible.
For more information, You may contact a authorized Witek service provider or
dealer

20
5
5. Cleaning the inside of the Scanner
Clean inside of the scanner with a soft lint-free cloth. In an alternating succession of
scanning documents, the accumulated paper-powder and dust inside the scanner causes a
scanning error.
Do not use water or neutral detergent to clean the inside of the
scanner.
Do not use aerosol sprays to clean the scanner. Aerosol sprays
cause dirt and dust to enter the scanner, resulting scanner failure
and malfunction.
When cleaning the scanner parts, dampen a cloth with modest
quantities of the cleaner. In addition, wipe off the cleaner
completely with a soft lint-free cloth to leave no residue on the
surface of the cleaned parts.
Attention