REALINN RL3200CB User manual

RL3200CB
1D Barcode Scanner
User Manual
Tech Support:
[e-mail]
[email protected]om
V.1

Before starting using this reader, please read the instruction
carefully and do not arbitrarily scan the setting barcodes
otherwise some settings may temporarily not functioning.
Please keep this user manual properly.
Technical support:
[e-mail]
[e-mail]
Please write down the scanner model and the detailed
information of the barcode scanner problem, which will help us
understand the specific problem and send you a solution in
time.

Contents
Technical Parameter
.........................
.....
1
Packing List
.........................
....
2
Product Introduction
.........................
....
2
Mode Indicator
.........................
....
2
Screen Time Setting
.........................
....
3
Button Function Instruction
.........................
3
Quick Start Guide
.........................
....
3
1. Pairing Mode
.........................
....
5
1.1 Bluetooth Pairing
.........................
....
5
1.2 2.4G Wireless Pairing
.........................
....
7
1.3 Wired Mode
.........................
....
9
Charging the scanner
.........................
....
9
FAQs
.........................
....
11
Optional Function settings
.........................
....
14
1. Scanning Modes
.........................
....
14
2. Uploading Modes
.........................
....
15
3. Auto Power Off Setting
.........................
....
17
4. Capital & Lowercase Switch
.........................
...
17
5. Beep Tone Setting
.........................
...
18
6. Decoding Volume Setting
.........................
...
18
7. Terminator Setting
.........................
...
18
8. Vibrate Setting
.........................
...
19
9. Resetting Standard Product Default
.........................
19
10. Input Method Setting
.........................
...
20
11. Time Stamp
.........................
...
21
12. Identify Barcode Type
.........................
...
22
13. Barcode Type On/Off
.........................
23
14. Insert and Delete Characters
.........................
28
ASCII Table
.........................
...
30

1
Technical Parameter
Model-Number
RL3200CB
Connection
Bluetooth + 2.4GHz Wireless + Wired
Distance
≤50m （Bluetooth），≤100m （Wireless）
Memory
16M = 100000 barcodes
Battery capacity
1500mAh
Sensor
CCD Image Sensor
Working current
3.5V
Charging power
5V-400mA
Printing Contract
>25%
Decoding accuracy
≥3.3mil@PCS90% CODE39
LED life
10000 hours
Button life
8000,000 times
Trigger Mode
Manual Trigger, Continuous Scanning, Auto-Sensing
Upload mode
Instant upload mode, Storage mode
Working time
Full load≈18hours, Normal use ≈3 to 10 days
CPU
ARM 32-bit Cortex
Indication
Buzzer，LED，Vibrate
Scanning angle
Angle of rotation36°, inclination± 60°,declination ± 60°
Drop test
2.0m
Working Temperature
-20℃ to 50℃
Barcode Type
1D: UPC, EAN, Code39, Code32, Codabar, Code128,
Code93, Interleaved 2 of 5, ITF14, Industrial 2 of 5,
Standard 2 of 5, Code 11, MSI/Plessey, GS1 Databar,
Matrix 2 of 5.

2
Packing List
Barcode Scanner * 1, Mini USB receiver * 1, Micro-USB Cable * 1
User Manual * 1, Short lanyard * 1, Long lanyard * 1
Product Introduction
Mode Indicator
Slow Blinking
Quick Blinking
2.4G Wireless indicator
2.4G Wireless Mode
2.4G Wireless Pairing Status
Bluetooth indicator
Bluetooth Mode
Bluetooth Pairing Status
Eyelets for threading the
provided lanyards

3
Screen Time Setting
Please visit the website : http://www.barcoderead.net/time.html
Scan the setting code on the screen to adjust the time which
displayed on the screen of scanner. The time displayed on this web
page is synchronized with the time displayed on your computer.
Please ensure that the time displayed on your computer is correct.
Button Function Instruction
By default, the functions of Button 1 and Button 3 are turned off.
Before opening the button function, please read the introduction
about button operation in detail.
Button 1 : (Turn Off By Default)
(1) Press Button 1 for 1 second - Instant upload mode / Storage
mode switch
(2) Press Button 1 for 8 seconds - Upload stored data
Button 2 :
(1) Press Button 2 for 1 second - Turn on the bar code scanner / Scan
barcodes
(2) Press Button 2 for 8 seconds - Turn off the bar code scanner
Button 3 : (Turn Off By Default)
(1) Press Button 2 for 1 second - 2.4Ghz wireless mode / Bluetooth
mode switch
(2) Press Button 2 for 8 seconds - Linking to a Host
Turn on/off Button function:
Note 1 :The function of button 1, 3 is turned off by default.
Please scan the setting bar code“Button 1,3 - On”before using
Button 1 and Button 3.
Note 2 : To prevent pressing Button 1 or Button 2 by mistake during
scan barcodes, please scan the setting code “Button 1,3-off ”.
Button 1,3 - On
Button 1,3-off*

4
1. How to link the reader to a Bluetooth ready device
through the operation button ?
(1) Press Button 2 to wake up the bar code scanner.
(2) Press Button 3 for 1 second to switch the pairing mode to
Bluetooth Pairing mode.
(3) Press Button 3 for 8 seconds. The Bluetooth indicator flashing
quickly indicates that the scanner is discoverable by the Host.
( Alternatively, you can scan setting codes“Bluetooth HID”and
“ Pairing”in order, and then the bar code scanner will become
automatically discoverable by the Host. See Bluetooth Pairing on
page 5)
(4) On the Host,use the dedicated Bluetooth application to search for
new devices. Select the”Bar Code Scanner HID”from the list of
available devices. If you receive an error message, it may be necessary
to disable security on the device.
(5) When the scanner finish pairing with the Host, the Bluetooth
indicator remains on and the buzzer beeps “di”.
2. How to switch the pairing mode from Bluetooth mode to
Wireless mode ?
(1) Press Button 2 to wake up the bar code scanner.
(2) Press Button 3 for 1 second to switch the paring mode to 2.4GHz
Wireless Pairing mode. The 2.4GHz wireless indicator shows up.
(3) Press Button 3 for 8 seconds. The 2.4GHz Wireless indicator
flashing quickly that the scanner is ready to connect to the device.
(4) Insert the USB receiver into USB port of device ( Make sure the
USB receiver is recognized by the device)The bar code scanner will
pair to the device automatically, the 2.4GHz Wireless indicator will
remains on and the buzzer beeps”di” ( If the 2.4GHz wireless
indicator keep flashing, please follow the 2.4GHz Wireless Paring
Mode introduction on page 7 to operate the scanner )
Note : After switching to Bluetooth Pairing Mode, the scanner will
pair to the previous paired device automatically. If not, please operate
“ forget the device “on the Bluetooth application of device and
then follow Bluetooth Pairing introduction on page 5 to re-connect
the device.

5
Quick Start Guide
The RL3200CB scanner has three connection modes: Bluetooth
Pairing Mode + 2.4GHz Wireless Mode + Wired Mode
It is suggested to use 2.4GHz Wireless Mode & Wired mode on
computers, use Bluetooth Wireless mode on the smart phones,
tablets.
Pairing Mode
1.1 Bluetooth Pairing
To pair with a Bluetooth enabled host:
Step 1. Press the Button 2 to wake up the bar code scanner. Scanner
beeps at a series of high frequency tones.
Step 2. Scan below “ Bluetooth HID ” and “ Pairing “ codes in
order. The Bluetooth indicator blinks quickly indicating that the
scanner is discoverable by the Host.
Step 3.On the Host, use the dedicated Bluetooth application to
search for new devices. Select the “ Bar Code Scanner HID” from
the list of available devices. When the scanner finish pairing with the
Host, the Bluetooth indicator remains on and the buzzer beeps
“di”.
Step 4. Scan “ Instant upload mode” code allow the scanner to
upload barcodes to host instantly.
Bluetooth HID
Pairing

6
Instant upload mode
Step 5. Open the Notepad or Word in the Host, put the cursor on the
blank, read labels for testing. When scanner decodes successfully
r,the scanner will beeps once and vibrates once( The beeper and
vibration indication can be turned off. See Decoding Volume Setting
on page 18 and Vibrate setting on page 19)
Note ：After pairing to the Host, the keyboard in the Host will not
appear automatically.
For iOS keyboard:
Method 1: To show or hide the iOS keyboard , please scan below
“Show/Hide iOS keyboard”
Method 2: Double click Button 2 twice quickly to show or hide the iOS
keyboard. This button function is able to turn off if users do not need
it.
** To show the
Android keyboard on in the Host, it needs to install the “CILICO
Bluetooth barcode input method” APP. Please contact us
（[email protected]） for the app and tutorial.
Note 3 : When uploading the barcode to the host, if some characters
Show/Hide iOS keyboard
Double Click Show/Hide iOS keyboard-On *
Double Click Show/Hide iOS keyboard-Off

7
of the barcode are missing, please try to slow down the transmission
speed.
High Speed*
Medium Speed
Low Speed
Very Low Speed
1.2 2.4GHz Wireless Pairing
The scanner is already paired with the provided mini USB receiver in
factory.Plug and play. If the scanner does not connect to host as
expected, please connect the scanner to the host follow below steps.
To connect to a computer :
Step 1. Press the Button 2 to wake up the barcode scanner. Scanner
beeps at a series of high frequency tones.
Step 2.Scan below”2.4GHz Wireless Mode “ and “ Pairing “ in
order. The 2.4GHz wireless indicator blinks quickly indicating that the
scanner is ready to connect to the host.
2.4GHz Wireless Mode
Pairing
Step 3.Unplug the USB receiver and then insert the USB receiver into
the USB port of computer again.The scanner beeps “ di “two times
at lowest frequency, indicate that the scanner connect to computer
successfully.

8
Step 4. Scan “ Instant upload mode” code allow the scanner to
upload barcodes to host instantly.
Instant upload mode
Step 5. Open the Notepad or Word in the Host, put the cursor on the
blank. Read labels for testing. When scanner decodes successfully
r,the scanner will beeps once and vibrates once( The beeper and
vibration indication can be turned off. See Decoding Volume Setting
on page 18 and Vibrate setting on page 19 )
Note 1: If fail to connect the scanner to computer, please unplug the
mini USB receiver and then plug the USB receiver into the USB port
again, repeat the connection steps above.
Note 2: If you want to switch the connection mode back to Bluetooth
mode, please press the Button 3 for 1 second or scan“Bluetooth
HID”and ”Pairing ”in order. See Button Function Instruction on
page 3 or “ Bluetooth Pairing”on page 5.
Note 3: If the scanner is not paired with the USB receiver within 1
minute, it will exit the the pairing status automatically.

9
1.3 Wired Mode
Step 1.Connect the scanner to computer via the provided USB cable.
After connect the scanner to computer, the scanner will automatically
switch to Wired Mode.The wireless indicator and the Bluetooth
indicator will disappear.
Step 2. Open the Notepad or Word in the Host, put the cursor on the
blank, read labels for testing. When scanner decodes barcode
successfully ,the scanner will beeps once and vibrates once( The
beeper and vibration indication can be turned off. See Decode Beeper
Setting on page 18 and Vibration setting on page 19 )
Note 1:
After unplugging the USB cable, the scanner will automatically switch
to Bluetooth Pairing Mode or 2.4GHz Wireless Mode.
Charging The Scanner
1. Battery Level
Open the Notepad or Word, put the cursor on the blank,scan
“Battery Level”code and users will know how much battery is left.
For example “ Battery : 100% ”.
2. Charging the scanner
Refer to the Charge Indicator on the screen or scan “ Remaining
battery “ setting code above.When it indicates the level of the
battery is 10% or lower, please charge the scanner in time.
Option 1. The scanner can be charged by connecting the scanner
directly to a computer through the micro-USB connector. You can use
the provided USB cable for this purpose.
Battery Level

10
Option 2. Charging the scanner via a wall plug connector ( usually
used to charge smartphones ) and the provided micro-USB cable.
Note 1 :
The battery charging indication shown on the screen.While
charging ,the LED ( Charge indicator ) is blinking.
Note 2 :
When the scanner is turned off, there is no indication appears when
the scanner is charging. To make sure the scanner is on
charging,please turn it on.

11
FAQS:
Q1. If I scan a label barcode, will it include the name of the
producing the file automatically?
The scanner works like a keyboard. The scanner does not interpret
what the barcode is, it just "types" out a string of alphabet numeric
characters that the barcode represents.
it's up to the database software you are using to interpret what that
string of characters means. Once you acquire the barcodes, you have
to correlate them to something more meaningful by either
purchasing a software service that will interpret the barcode and
relate it to a product, or you can use your own internal inventory
system to assign the barcodes to specific products.
After creating the relationship between your barcode and the
corresponded information ,when you enter the barcode into the
software by the scanner,your software will look up the barcode and
then output the related information of your product.
Q2. My smart phone can not find the scanner.
A. Make sure the phone is android 3.0 or above, it can be connected
directly
B. The scanner was set to Wired Mode and 2.4GHz Wireless Mode.
Or the scanner is not in pairing status.
Please unplug the USB cable and USB receiver from USB ports first,
and then scan the setting code “Bluetooth HID””Pairing” to switch
the connection mode.
C. The scanner has been connected to other smartphone. Please
delete/forget the“ Bar Code Scanner HID“ from the list of available
device on that smartphone.

12
Q3. Scanner is connected, but the barcode can not be uploaded to
my phone/tablet/PC.
The scanner is in storage mode. All decoded barcodes are stored in
the buffer of scanner.
Please scan the setting code “Instant Upload Mode”on page 15.
Q4. Some barcodes can not be read, why?
A. Incomplete and unclear barcodes might not be read.
B. It is possible that the setting is off by default for some barcode
types which are not commonly used. You need activate a specific
barcode type （on page 23）to get it working. Please feel free to
contact our Customer Service Team for further assistance if you don't
know the exact type of barcode that you are referring to.
Q5. Why does scanner not read the barcode exactly. When I use
the scanner to read a barcode of an item, I get a different result
from the barcode itself.
Example 1, There are two separate barcodes together. It scanned
the first 12 digits in the barcode but not the last five.
Solution：Please scan setting code “UPCA 2/5 Extra Code -ON”on
page 23.
Example 2, The original barcode is “abc12345”， the scanning
result is “+A+B+C+D12348”，insert “+” between characters.
Solution：Please scan the setting code “Code 39 Full ASCII-ON ”
on page 26.
Example 3, Scan Codabar barcode.The original barcode is
“123456”, but the scanning result is “A123456A” or
“ A123456B “.
Solution: Please scan the setting code “Output Start&Stop
Digit- OFF”on page 27.

13
Q6. Is there any barcodes to remove auto-enter after every
scanning?
To remove the auto-enter, please read the code “None” on page 18.
If none of the above is the problem you encountered, please send us
a clear bar code picture and the result you got, our customer service
will help you solve the problem.
Example 4,Scan Code 39 barcode.The original barcode is
“123456”,but the scanning result is “ *123456* “.
Solution: Please scan the setting code “Output Start&Stop Digit
- OFF”on page 26.
Example 5, A UPCE barcode”01234567 “,has 8 digits. The
system request to input 12 digits.
Solution: Please scan the setting code “UPCE to UPCA - ON”on
page 24.

14
Optional Function Settings
The reader is factory-configured with a set of standard default
features. You can select other options and customize your reader
through programming bar codes in this booklet.
1. Scanning Modes
The scanner can operate in one of several scanning modes.
1.1 Manual Trigger Mode
When press the Button 2, the CCD red light shows up and and the
scanner attempts to read a label.
1.2 Continuous Scanning Mode
There’s no need to press the Button 2 in this scanning mode. The
CCD red light of the scanner will be on all the time.
1.3 Auto-Sensing Mode
There is no need to press the Button 2 in this scanning mode.Shaking
the scanner slightly, or something passes by the scanning window the
CCD red light will shows up. Putting the label under the CCD red light,
the scanner will read it.
Manual Trigger Mode
Continuous Scanning Mode
Auto-Sensing Mode

15
2. Uploading Modes
The scanner can operate in one of two uploading modes.
2.1 Instant Upload Mode
After scanning label , the decoded barcode will be instantly uploaded
to where the cursor is. The buzzer beeps “ di “ when the scanner
successfully read and upload the decoded barcode.
Instant Upload Mode*
2.2 Storage Mode
In storage mode, all decoded barcodes will stored in the memory
of the scanner and will not be uploaded to the Host instantly. You
can batch upload all decoded barcode by scanning the setting
code”Upload data “
An operation in storage mode is strongly recommended under the
following scenarios:
1) During the scanning process, the device often leaves the
Bluetooth / wireless signal range;
2) Due to a high quantity of blocking objects, the Bluetooth / wireless
signal’s stability can’t be ensured.
Storage Mode

16
** To batch upload all decoded barcodes, scan setting code”Upload
Barcodes “
** To show total number of batch decoded barcodes, open the
Notepad or Word,put the cursor on the blank, and then scan the
“Show total storage”setting code. It will inputs “The total
numbers： xxxxxxx”.
** To clear all decoded barcodes, scan setting code “ Clear Decoded
Barcodes “ .
Note : Do not read setting code “ Clear Decode Barcodes” in
mistake. Once scan setting code”Clear Decoded Brcodes”, all data
will be cleared immediately. The data will no longer be restored.
Upload Decoded Barcodes
Show Total Numbers
Clear Decoded Barcodes