WiTi Anti Theft How to use

Anti Theft
Operation &
Installation
Guide

WiTi Anti-Theft System
In the event an attempt is made to steal the caravan or trailer, WiTi detects movement and ini-
tiates anti-theft mode. All the lights ash, the alarm sounds for 30 seconds and the brakes are
applied to bring the caravan or trailer to a complete stop, making it impossible to tow. The brakes
are applied for ve seconds and then released if there is no movement to prevent the battery
from discharging unnecessarily.
To activate the anti-theft press the button on the remote control and the lights will ash once fol-
lowed by a three second safety pause and then two ashes to indicate the system is armed. To
deactivate press the button on the remote control and the lights will ash once.
WiTi incorporates an advanced safety system to ensure the anti-theft system cannot be acci-
dently activated whilst the caravan or camper trailer is being towed. After activating the system,
if movement is detected during the three second safety pause the system will not arm. The lights
will not ash twice and the system must be deactivated again before another arming sequence
is initiated.
On initial power up WiTi Anti-Theft needs to be initialised. To do this press the button on the
remote control and the lights will ash once. The system is now initialised. This only needs to
be done on power up. If power is removed from WiTi Anti Theft then the system needs to be
initialised again.

WARNINGS & SAFETY INSTRUCTIONS
Do not operate WiTi unless you have read and understood this manual and
WiTi is installed as per the instructions.
Specications
Trailer Unit
Nominal System Voltage 12V
Operating Voltage 9V-15V
Standby Current <10mA
Operating Temp -20C – 60C
Max. Trailer Axles 3 Axles
Braking circuit max draw 25A
Maximum Rated Current 30A
Weight 300g
Contents
3
1. Trailer Unit
2. Alarm horn
3. Two Remote Controls
• Ensure the cable used to install WiTi is of adequate thickness to provide the necessary
current for the circuit.
• WiTi must be installed away from environmental conditions that may cause damage to
the unit’s circuitry including water, salt spray and humidity.
12

Anti Theft Installation
The unit must be installed vertically with
the wiring harness protruding from the bottom
of the unit. WiTi uses gravity to initialise the
anti-theft system and if not installed vertically
functionality could be compromised.
WiTi Anti Theft can be installed in any area
that makes practical sense, typically next to
or near the battery in the caravan or trailer.
WiTi can be secured to any at surface using
strong double sided tape.
The horn must be installed at least 1 metre
away from the Trailer Unit and on a di󰀨erent
mounting surface to prevent interference.
The caravan or trailer battery must be
connected to an acceptable charging circuit -
either solar panels, anderson plug or DCDC
charger.
INSTALLATION INSTRUCTIONS
Wiring Instructions
The Anti Theft system is supplied with two
connectors, an 8 pin unit for the lights, brakes
and horn circuits and a 2 pin connector for
power. Install the wiring on the corresponding
plugs supplied before connecting to the Trailer
Unit.
Connect one of the terminals on the horn
to the green and white wire and the other
terminal to an earthing point.
Note: If a break away option is installed there
will be two additional blue wires on a separate
2 pin connector. These must be connected to
the break away switch on the caravan.
Wire
Colour
Function
Yellow Left Indicator
Green Right Indicator
Red Brake Light
Brown Driving Lights
Black Reverse Lights
Blue Electric Brake Output
White Earth Return
Green / White
Alarm output. Connect to
the horn. The horn can be
earthed to the chassis or any
earth point. It is not polarity
sensitive.
Wire
Colour
Function
Red 12V+ Connect to the positive termi-
nal of the battery.
Black NEG Connect to negative terminal
of the battery.
Wire Colour Function
Blue X 2 Break away Switch