WOBBEGONG CRUZER Operating and safety instructions

WOBBEGONG WATERSPORTS
CRUZER 11’ STAND UP PADDLEBOARD (SUP)
WELCOME GUIDE

Come paddle
with the ‘Gong
Thanks for choosing Wobbegong Watersports.
This Welcome Guide will provide some practical information
on getting started with your new board.
In the box you will find the following items:
Stand up paddleboard
(You’ll definitely need this bit)
Waterproof
phone case
For those all
important calls on
the water
Repair kit
Because accidents
can happen
Packing strap
Keeps the ‘Gong
secure
Heavy duty bag
With wheels and backpack straps Adjustable paddle Fiberglass for strength and weight
Skegs
3x for extra stability
Leash
Don’t want to be losing it!
2-speed pump
Inflates and deflates

Inflating the board
1. Unpack and unroll your SUP on asmooth, clean and flat
surface.
2. Remove the valve cover (b) and ensure that the valve (a)
is in the “out” position.
3. Attach the hose to the pump at the INFLATE valve.
4. Connect the hose to the valve on the SUP by firmly pushing
inwards and twisting clockwise.
5. Inflate to amaximum of 15 PSI.
6. Remove the hose from the valve and replace the cap.
7. NB.If air continues to escape from the valve after the
removal, the valve position is in the “in” position and will
need to be twisted to the “out” position before inflating
again.
8. To deflate the board, remove the valve cap press and twist
the valve to the “in” position.Keep your face away from
the valve as air will release at high pressure.
PSI
0
2
4
6
8
10
12
14
16
18
20
WARNING:Only use the pump provided to
inflate or deflate your SUP.DO NOT use an air
compressor or electric pump as you risk
over-inflating and/or severely damaging
the SUP beyond repair.

Preparing to paddle
1. Attach the skegs as per the diagram below.The larger
skeg should fit into the central slot, with the smaller skegs
either side:
Slide the skeg
fully into the
channel.
Insert the
gasket fully into
the slot until it
clicks.
2. Attach the leash to the rear D-ring on the board.The other
end should be strapped to your ankle during use.
3. Assemble the paddle as per the below diagram:
4. Adjust the height of your paddle accordingly.It should be
between 12”and 18”(or about ahand’s width) above head
height.
GO PADDLING!

Tips & advice
Place your feet shoulder width
apart from each other in the
center of the board.Use the
central handle as areference
point.
Grab the T-handle of the
paddle with your strongest
hand.Place the other hand
further down the shaft.Relax
your knees!
Plunge the paddle vertically
downwards into the water and
sweep back past your body.
Repeat on the other side!

Safety & Care
•The maximum load weight of the SUP is 120kg.Do not
exceed this weight at any time.
•Always attach the provided leash to your calf or ankle and
secure to the D-ring at the rear of the board.
•Ensure that you consider the appropriate clothing for the
weather or climate in which you are paddling.It is highly
recommended that you wear abuoyancy aid or personal
flotation device at all times when you are on the water.
•The board should be thoroughly cleaned and dried after
each use.
•Do not use harsh chemicals for cleaning.Most dirt can be
removed with amild soap and fresh water.
•The board should be stored inside the provided bag in a
cool dry environment and away from direct sunlight.
•Please ensure that no water gets inside of your SUP as this
can severely damage the board.Drain any water and dry
thoroughly before re-attaching the valve and inflating.
•From time-to-time your valve may need tightening to
prevent any air leaks.To tighten the valve first ensure that
the board is fully deflated.Insert the tool into the valve and
push upwards from the underside of the board to ensure
that the valve is making firm contact with the thread.Next,
turn the tool clockwise until the valve is fully tightened and
secure.