Wolf Gas Range User manual

Gas Range
Installation Guide
SPECIFICATIONS, INSTALLATION,
AND MORE

2 | Wolf Customer Care 800.222.7820
Gas Range
Contents
3Gas Range
4Safety Precautions
5Specifications
8Installation
11 Troubleshooting
Features and specifications are subject to change at any
time without notice. Visit wolfappliance.com/specs for the
most up-to-date information.
Important Note
To ensure this product is installed and operated as safely
and eciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or prod-
uct damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.

wolfappliance.com | 3
Product Information
Important product information, including the model and
serial number, are listed on the product rating plate. The
rating plate is located on the bottom of the control panel,
at the far right, just above the oven door. Refer to the
illustration below.
If service is necessary, contact Wolf Factory Certified
Service with the model and serial number. For the name of
the nearest Wolf Factory Certified Service or for questions
regarding the installation, visit the Product Support section
of our website, wolfappliance.com, or call Wolf Customer
Care at 800-222-7820.
RATING PLATE
Rating plate location
Gas Range

4 | Wolf Customer Care 800.222.7820
IMPORTANT INSTRUCTIONS
WARNING
A child or adult can tip this appliance and be
killed.
Verify the anti-tip device has been properly
installed and engaged. Ensure the anti-tip
device is re-engaged when this appliance is
moved. Refer to the illustrations below for
how to verify correct installation.
Do not operate this appliance without the
anti-tip device in place and engaged. Failure
to do so can result in death or serious burns
to children or adults.
To reduce the risk of burns, do not move this
appliance while hot.
• This appliance is equipped with casters on two
or more legs and must be installed on ⁄" (3)
thick commercial grade vinyl composition floor
finishing materials or equivalent.
• This appliance is not approved for downward
airflow ventilation or air curtain equivalent.
• A minimum 20" (508) riser is required when
installing against a combustible surface.
Safety Precautions
ANTI-TIP
DEVICE
ANTI-TIP
DEVICE
ENGAGED
Anti-tip device location Anti-tip device engaged

wolfappliance.com | 5
Electrical Requirements
Installation must comply with all applicable electrical codes.
Locate the electrical supply flush with the wall or floor and
within the shaded area shown in the illustration on page 7.
A separate circuit servicing only this appliance is required.
A ground fault circuit interrupter (GFCI) is not recom-
mended and may cause interruption of operation.
ELECTRICAL REQUIREMENTS
Electrical Supply grounded, 110/120 VAC, 60 Hz
Service 15 amp dedicated circuit
Receptacle 3-prong grounding-type
Power Cord 6' (1.8 m)
Specifications

6 | Wolf Customer Care 800.222.7820
The range must be connected to a regulated gas supply.
The supply line must be equipped with an approved exter-
nal gas shut-o valve located near the range in an acces-
sible location. Do not block access to the shut-o valve.
Refer to the illustration below.
A gas supply of ⁄" (19) ID line must be provided to the
range. If local codes permit, a certified, 3' (.9 m) long, ⁄" (13)
or ⁄" (19) ID flexible metal appliance connector is recom-
mended to connect the units ⁄" NPT female inlet to the
gas supply line. Pipe joint compounds suitable for use with
natural or LP gas should be used.
The appliance and its shut-o valve must be disconnected
from the gas supply piping system during any pressure
testing of the system at test pressures in excess of .5 psi
(3.5 kPa). The appliance must be isolated from the gas
supply piping system by closing its individual manual shut-
o valve during any pressure testing of the system at test
pressures equal to or less than .5 psi (3.5 kPa).
Wolf natural gas ranges will function up to 8,600' (2621 m)
in altitude without adjustment. If the installation exceeds
these elevations, contact an authorized Wolf dealer for a
high altitude conversion kit. LP gas ranges do not require
conversion.
Gas Supply
Installation must comply with local codes, or in the
absence of local codes, with the National Fuel Gas Code.
Locate the gas supply within the shaded area shown in the
illustration on the following page.
The range is equipped for use with natural or liquid pro-
pane (LP) gas. The product rating plate has information
on the type of gas that should be used. For rating plate
location, refer to the illustration below. If this information
does not agree with the type of gas available, check with
the local gas supplier. The gas pressure regulator is built
into the unit.
GAS REQUIREMENTS
NATURAL GAS WC
Supply Pressure 5" (12.5 mb)
Min Line Pressure 7" (17.5 mb)
Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)
LP GAS WC
Supply Pressure 10" (25 mb)
Min Line Pressure 11" (27.4 mb)
Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)
Specifications
SHUT-OFF VALVE
OPEN POSITION
GAS SUPPLYTO APPLIANCE
Gas shut-o valve
RATING PLATE
Rating plate location

wolfappliance.com | 7
Gas Range
INSTALLATION
12"
(305) GAS
5"
(127)
2" (51)
73/4" (197)
53/4"
(146)
12"
(305)
10" (254)
FRONT VIEWSIDE VIEW
*Without ventilation hood, 42"(1067) minimum clearance countertop to combustible materials, charbroiler and GR488 require non-combustible materials.
NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,
combustible materials cannot be located within this area.
For island installation, 12"(305) minimum clearance back of range to combustible rear wall above countertop.
13"
(330)
18"
(457)
6"
(152)
3"
(76)
LOCATION OF GAS AND
ELECTRICAL EXTENDS
ON FLOOR
W
OPENING WIDTH
30" (762) TO 36" (914)
TO BOTTOM OF
VENTILATION HOOD*
E
G
OPENING WIDTH W
30" Model 30" (762)
36" Model 36" (914)
48" Model 48" (1219)
60" Model 60⁄" (1530)
Specifications

8 | Wolf Customer Care 800.222.7820
Preparation
Before moving the range, protect any finished flooring and
secure oven door(s) closed to prevent damage.
To lighten the load or to fit through a door way, the oven
door(s) can be removed. Remove only if necessary. Do not
remove the griddle or any other component. Door removal
should be done only by a certified installer or service tech-
nician.
For removal, a hinge pin will be inserted into the appropri-
ate hinge shown in the illustrations below. The pin(s) are
located inside the oven door. For single oven ranges, the
hinge pin must be inserted in the right hinge. For double
oven ranges, the pins must be placed in the outer two
hinges.
CAUTION
Failure to insert the hinge pin in the appropriate
hinge arm will cause damage to the range.
Installation
OVEN DOOR REMOVAL
1 Insert the hinge pin into the appropriate hinge.
2 Remove the lower kickplate assembly to access the
lower hinge retainer mounting screws.
3 Open the oven door and remove both upper and lower
hinge retainer mounting screws. The oven gasket may
have to be moved slightly to access the bottom screws.
4 Move the hinge retainer plate forward slightly. The
hinge retainer plate will remain on the door hinge after
the mounting screws have been removed.
5 Carefully close the oven door to approximately 60°,
then lift the door up and out. A slight rocking motion
may be required for removal.
SPRING HINGES
SPRING HINGE
SPRING HINGES
SPRING HINGE
Single oven ranges Double oven ranges
KICKPLATE
UPPER
MOUNTING
SCREW
HINGE
RETAINER
PLATE
HINGE
PIN
Oven door removal

wolfappliance.com | 9
Leveling
Raise the range to its desired height by adjusting the front
legs and rear casters. The front legs can be adjusted by
rotating the hexagonal leg clockwise to raise and coun-
terclockwise to lower. The rear casters can be adjusted by
rotating the wheel assembly.
Placement
Do not lift or carry the oven door by the door handle. The
range has rear casters which allow for easy movement by
lifting the front of the unit.
Use an appliance dolly to move the range near the open-
ing. Remove and recycle packing materials. Do not discard
the anti-tip bracket supplied with the range.
If a riser has been specified, refer to installation instructions
packaged with the riser. The riser must be installed before
the range is installed.
Installation

10 | Wolf Customer Care 800.222.7820
ANTI-TIP BOLT ADJUSTMENT
Once the bracket is secure, adjust the anti-tip bolt so the
top of the washer is ⁄" (22) maximum from the floor. Slide
the range into the opening and verify the anti-tip bolt is
engaged. Refer to the illustrations below.
Anti-Tip Bracket
To prevent the range from tipping forward, the anti-tip
bracket must be installed. To ensure the anti-tip bolt
engages the bracket, position the bracket 3" (76) from the
left side of the opening. Refer to the illustration below.
INSTALL BRACKET
Drywall application: After properly positioning the anti-tip
bracket, mark the holes, then use a Phillips screwdriver
or a low rpm power drill to drive the wall anchor into the
surface of the wallboard until flush. Pre-drill the holes if
needed. For hard wallboard or double-board construction,
use a ⁄" drill bit. For solid plaster, use a ⁄" drill bit. Refer
to the illustration below. Use the #8 screws and flat wash-
ers to fasten the bracket to the wall.
Wood floor application: After properly positioning the
anti-tip bracket, drill ⁄" (5) pilot holes through the floor.
Use the #12 screws and flat washers to secure the bracket
to the floor.
Concrete floor application: After properly positioning
the anti-tip bracket, drill ⁄" (10) holes into the concrete a
minimum of 1⁄" (38) deep. Use the ⁄" wedge anchors to
secure the bracket to the floor.
7/8" (22) MAX
ANTI-TIP
BOLT
ANTI-TIP
DEVICE
ENGAGED
Anti-tip bolt adjustment Anti-tip bolt engaged
3" (76)
ANTI-TIP
BRACKET
ANTI-TIP
BRACKET
WALL
ANCHOR
Anti-tip bracket location Wall anchor installation
Installation

wolfappliance.com | 11
Gas Supply Connection
All connections to the gas piping must be wrench-tight-
ened. Do not overtighten or allow pipes to turn when
tightening.
If a flexible metal connector is used, verify it is not kinked,
then attach the gas supply line to the regulator on the
range. Open the valve and check for leaks by placing a
liquid detergent solution onto all gas connections. Bub-
bles around the connections indicate a gas leak. If a leak
appears, close the shut-o valve and adjust the connec-
tions.
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &
Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
Troubleshooting
IMPORTANT NOTE: If the range does not operate properly,
follow these troubleshooting steps:
• Verify electrical power is supplied to the range.
• Verify the gas supply shut-o valve is in the open
position.
• If the range does not operate properly, contact Wolf
Factory Certified Service. Do not attempt to repair the
range. Wolf is not responsible for service required to
correct a faulty installation.
Installation