Wolverine Airsoft STORM User manual

Page 1
www.wolverineairsoft.com
OnTank / HighPressure
OWNER’S MANUAL
www.wolverineairsoft.com
WOLVERINE AIRSOFT

Page 2
www.wolverineairsoft.com
Table of Contents
Important Safety Notices 3
Getting Started 4
Installation / Use / Tournament Lock 5
InGrip Installation / Use 6
Maintenance 8
Don’t Forget to
Register Your Warranty!
Your STORM Regulator is
backed by Wolverine Airsoft’s
limited warranty. Scan the QR
code or visit www.wolverineair-
soft.com/warranty to read our
full warranty and register your
STORM Regulator.

Page 3
www.wolverineairsoft.com
Important Safety Notices
1. High pressure air systems contain air compressed
under great pressure and should always be treated
with care to avoid serious injury or death. Always
be sure that your tank and tank regulator is in good
working order before use with the Wolverine Airsoft
STORM regulator.
In particular, ensure that all threaded components of
the tank regulator are properly torqued to avoid all
or part of the tank regulator from unscrewing from
the tank during disassembly of the STORM regulator
from the tank. Please consult a paintball or airsoft
professional tech if you have any questions regarding
the safe servicing of your tank.
2. The STORM InGrip regulator is designed for use
with a standard paintball style remote line. Tradition-
al HPA lines used for airsoft ARE NOT RATED FOR
HIGH PRESSURE between the tank and regulator.
Using a standard airsoft airline with the InGrip regu-
lator will result in a rupture of the air line and could
cause serious injury.
3. Never leave HPA or CO2 tanks in direct sunlight
(including during play), in parked cars, or otherwise
submit them to excessive heat. Heat will cause an
unsafe rise in pressure in the tank which could lead
to serious injury or death.
When using CO2 always be sure to have the
tank securely mounted vertically on your body.
Allowing the CO2 tank to partially or fully invert
will result in liquid CO2 being sucked into the
gun which can result in an unsafe spike in pres-
sure/velocity and could damage your Wolverine
Airsoft engine.

Page 4
www.wolverineairsoft.com
Getting Started
The Wolverine Airsoft STORM OnTank and
STORM InGRIP regulators are intended for use
with standard pressure or low pressure paintball
HPA tanks. The InGrip regulator can also be used
with standard CO2 tanks. Pressure is adjusted
by turning the set screw on the front of the reg-
ulator using the included 3/32” hex key.
Specifications
Pressure adjustment Range: 40-140 PSIG
(60-180 PSIG for HighPressure)
Input Pressure Range: 300-1000 PSIG
Pressure Adjustment Rate: ~15 PSI/Turn
Recommended Service Time: 100,000 shots or every
6 months
OnTank HighPressure InGrip
Pressure adjustment screw
Tournament
Lock

Page 5
www.wolverineairsoft.com
STORM OnTank/HighPressure
Installation
To install the regulator, simply thread the
regulator onto the top of your HPA tank.
Screw the regulator all the way down until
it stops. The final ½-¾ turn will open valve
on the tank regulator to pressurize the
system.
Removal
To remove the regulator, unscrew the
regulator one complete turn from the tank.
Fire the gun to vent any pressure past the
regulator. Completely remove the regulator
from the tank. Do not partially unscrew
the regulator and then re-tighten it without
completely removing the regulator from the
tank as it may pinch your tank O-ring.
Tuning
Adjust the pressure on the tank by using
the included 3/32 hex key to turn the small
set screw on the front of the regulator. The
regulator is not self-venting so you will need
to have the gun connected and fire the gun
when adjusting the pressure lower before
the gauge will show the new pressure.
Tournament Lock
To engage the tournament lock, slide the
black sleeve down to cover the pressure
adustment set screw. Then, simply secure
the sleeve with a zip tie.
Decrease
pressure
Increase
pressure

Page 6
www.wolverineairsoft.com
STORM OnTank/HighPressure
Installation
To install the STORM InGrip regulator remove the stock airline from
the back of your Wolverine Airsoft HPA engine using a 5/16” wrench.
Install the airline with the ¼” macro line onto the engine and reinstall
engine and gearbox in the gun.
Slide the InGrip base over the tubing up flush against the bottom
of the gearbox. Trim the tubing with a sharp pair of scissors 1/8”
past the end of the InGrip base. Remove the InGrip base. Install the
grip and the InGrip base using the four included M3 screws. If your
gearbox only has two threaded holes for attaching the grip, just use
two of the included screws.
Screw the regulator into the InGrip base and tighten using the includ-
ed spanner wrench. The standard ASA to remote adapter included
with most remote lines can be screwed directly into the base of the
regulator.
Removal
Disconnect the remote line from the gun. Fire the gun until all pres-
sure is vented. Unscrew the ASA to remote adapter from the bot-
tom of the InGrip regulator. You may find a set of channel lock pliers
to be helpful in this. Use the included spanner wrench to unscrew the
regulator from the InGrip base.
Tuning
In order to change the pressure, the regulator must be removed
from the grip of the gun. Adjust the pressure with the regulator
removed from the gun. One complete turn of the adjustment screw
adjusts the pressure approximately 15psi and 25FPS.

Page 7
www.wolverineairsoft.com
Maintenance
Your STORM regulator is designed to require very little maintenance.
However if you feel the regulator is in need of lubrication you can
disassemble by removing the three flat head screws from the side of
the regulator. Use TechT Gun Sav or another O-ring safe lubricant
on all o-rings and reassemble.
Pressure
adjustment
screw
Base Plate
5mm Ball Bearing
Spacer
AS-568
010 O-Ring
Shims
Spring
1.2 x 5mm
O-Ring
Piston
Tournament
Lock
1.2 x 17mm O-Ring
Gauge
Screw (x3)
1/8” MPT
Connector
Reg Seat
Assembly
AS-568 016
O-Ring
STORM
HighPressure
1.5 x 15mm
O-Ring
AS-568
111 O-Ring
AS-568
113 O-Ring
*STORM InGrip
Correct
Reg Seat
Orientation

www.wolverineairsoft.com
Need professional help?
To find a retailer close to you visit:
www.wolverineairsoft.com/dealers