Wonderfire Lincoln BR517S User manual

OWNER’S GUIDE
for
This guide is intended to help you care for your Wonderfire gas fire.
It gives sufficient details to enable your gas fire to be operated andmaintained
Please read carefully before using your gas fire and keep for future reference.
Please keep your Owner Guide in a safe place together with the Installer Guide.
600B349/01
MODEL
BR517R & BR517S
(G.C. 32-032-11)&(G.C. 32-032-12)
Rear and Side Fan
Flued Inset
Gas Fire
with
LINCOLN
Front

2
22
2
Thank you for choosing Wonderfire.
All Wonderfire appliancesare designedto meet the most stringent
quality,performanceand safety requirements to provide our
customers with many years’ trouble-free service.
Your owner guide aims to improve your understanding and
appreciation of your gas fire by providing simple and informative
instructionstoensurethat youbenefitfromtheexcellent
performance and features it has to offer.
Ifyourequirefurtherassistanceor anyadviceabout gas ingeneral,
the Wonderfire service department will be pleased to help.
Inthe UnitedKingdompleasetelephone0121 386 6203.
Inthe Republicof Irelandpleasetelephone353 183 75114
Page
PART 1: SAFETY 3
•Important information
PART 2: OPERATING INSTRUCTIONS 4-5
•How to light your fire
•How to turn your fire off
•The Flame Sensing Device &
Flue Ventilation Monitoring System
•Gas Consumption
PART 3: MAINTENANCE 6-8
•Cleaning your fire
•Refitting the Coals & Walls
•General Servicing
As supplied, this appliance is for use with natural gas (G20)
When converted using conversion kit no. 591149 this appliance
is for use with propane gas (G31)
This appliance is for use in the United Kingdom (GB) and the
Republic of Ireland (IE) only.
CONTENTS
CUSTOMER CARE

3
33
3
DO
•Have the fire installed by a competent person. In the
United Kingdom, installation must be in accordance with
the latest edition of the Gas Safety (installation & use)
Regulations and the IEE Wiring Regulations. In the
Republic of Ireland, installation must be in accordance with
all national and local regulations in force and the ETCI
National Rules for Electrical Installation.
•Have the fire installed in accordance with the installation
instructions
•Provide a minimum distance of 750mm from the top
surface of the hearth to any shelf made ofwood or other
combustible material where the shelf isnot more than
150mm deep (This will give a clearance of 150mm above
the top of the fire).
For a shelf deeper than 150mm, add12.5mm to the
clearance for every 25mm of additional shelf depth (see
figure 1).
•Make sure that any combustible wall finish or cladding is
removed from the area withinthe outer surround of the fire
(see figure 1)
•Make sure that the fire is on a non-combustible hearthand
that the hearth is at least the size shown in figure 1.
•Provide a suitable guard whichcomplies with BS6539 or
6778 for the protectionof young children,the elderly and
the infirm. Such a guard is also recommended for the
protection of pet animals. (Although this fire conforms to
all the applicable standards, it is a heating appliance and
certain parts of its surface will become hot.)
•Switch the fire and fan off and allow to cool before
attempting to clean, service, etc. This appliance retains heat
for some time after it has been switched off
•Wait three minutes before attempting to relight if the fire is
switched off or if the flames are extinguishedfor any reason.
(Your fire is fitted with a safety device which will
automatically shut off the gassupply to the fire if, forany
reason, the flames go out or if the fan is not working.)
•Get advice about the suitability of any wall covering near
your fire. Soft wall coverings (e.g. embossed vinyl, etc.)
•whichhave a raised pattern, are easily affected by heat.
They may, therefore, scorch or become discoloured when
close to a heating appliance. Please bear this in mind
whenever you are considering redecorating.
•Provide a minimum clearance of 178mm between the outer
surround sidesand any corner wall or other projection (see
figure 1). Please bear this in mind if ever you are
considering altering the room.
DON’T
Put any paper or other material on the fire.
Hang clothing,towels or any other fabrics over the fire.
Fill in the space behind the case.
Add any extra coals above the number statedin this guide - It
could cause a safety hazard.
Place carpets, rugs or any other combustible material over the
hearth.
Block in the space behind the top edge of the duct covers (Side
flue model only). See Part 3: Maintenance.
PART 1: SAFETY
CAUTION
IF YOU SMELL GAS...
•DON’T TURN ELECTRICAL SWITCHES ON OR
OFF
•DON’T SMOKE OR USE NAKED FLAMES
•DO OPEN DOORS AND WINDOWS TO GET RID
OF THE GAS
•DO TURN OFFTHE GAS AT THEMETER
•DO CALL THE GAS EMERGENCY SERVICE - IN
THE PHONE BOOK UNDER “GAS”
PLEASE NOTE
W
hen operating your fire for the first time, some vapours ma
y
be given off which may cause a slight odour and could possibly
set off any smoke alarms in the immediate vicinity. These
v
apours are quite normal with new appliances.They are
totally harmless and will disappear after a few hours use.
This fire is supplied with ceramic “coals” which simulate a
real coal fire. The coals are designed for easy refitting if
removed and are totally safe to handle.
The burner in this appliance has been designed to give an
authentic coal fire flame effect.Due to the nature of this kind
of burner,there may be various “popping” and flame noises
not usually associated with more conventional gas fires. As
w
ith a real coal fire, these noises are perfectly normal and safe.
A
fter some use, the coals and the ceramic walls may change
colour. This is quite normal and will not affect the safety or
performance of the fire.
A
t times of very windy weather or low voltage during peak
electricity demand, a slight click may be heard. This is caused
by the fan control switching between its boost and normal
speeds.
THIS APPLIANCE MUST BE EARTHED

4
44
4
HOW TO LIGHT YOUR WONDERFIRE LINCOLN GAS FIRE
The controlsare shown in Figure 2.
Check that the main isolating switch is on.
Remove the bottom front cover. The controls are behind this cover.
Check that the red indicator light is on.
Press and hold in the “ON” switch. Within two seconds, the fan motor should
start and the indicator light should go out.
Release the “ON” switch. The fan should continue to run.
Depress the control knob and turn partially to the “PILOT/IGN” position until
you feel some resistance.
Keep the knob depressed at this position for a few seconds to allow gas to flow
to the pilot.
While keeping the knob depressed, turn to the “PILOT/IGN” position. While
turning, a spark should light the pilot. The pilot flame can be seen below
the roundcoal at the front left side.
Keep the knob depressed at the “PILOT/IGN” position for a further ten
seconds then release it. The pilot flame should stay alight.
Slightly depress the knob and turn it to “LOW”. Release the knob. Within a
few seconds the main burner should light at its low setting.
Slightly depress the knob and gradually turn it towards “HIGH” until the
burner is at your desired setting. The burner flames will gradually increase
until the knob is at the “HIGH” position.
If the spark ignition fails, the fire can be lit manually by inserting a lighted
taper alongside the left side wall inside the fire box (as shown in figure 3)
and depressing the control knob at the “PILOT/IGN” position.
Note: If the fire goes out while setting the control, repeat the full lighting
procedure.If the fire repeatedly goes out, have the fire serviced.
HOW TO TURN OFF YOUR WONDERFIRE LINCOLN
GAS FIRE
To turn off the main burner but leave the pilot alight slightly depress the control knob and
turn to “PILOT/IGN”. Leave the fan switched on.
To turn the fire fully off slightly depress the control knob and turn to “OFF”.Press the
“OFF” switch to turn the fan off. The indicator light will come on to show that the electrical
supply to the fire is live. If the fire is not likely to be used again for a long time we suggest that
the mains isolating switch for the fire is switched off.
Wait at least three minutes after turning the fire off before relighting.
While cooling, the coals may make some crackling noises. This is quite normal.
Figure 3 Lighting witha taper
PART 2: OPERATING INSTRUCTIONS
Figure 2 The Controls
Figure 1

5
55
5
THE FLAME SENSING & FLUE BLOCKAGE SAFETY SYSTEM
For your safety, this appliance is fitted with a flue blockage safety device which will shut down
the appliance in the event of abnormal flue conditions.
This device will also shut down the appliance if the pilot flame goes out due to lack of oxygen or
for any other reason.
The system includes a probe which senses the heat from the pilot flame. If this probe is cool, the
system will prevent any gas flow unless the control knob is kept depressed at the “PILOT/IGN”
position.
The system also includes an atmospheric pressure detector. This will shut off the gas supply if
the fan is not working.
If there is a blockage preventing the flow of exhaust fumes out of the flue, the fan will switch to a
high boost speedto attempt to clearthe blockage. If theboost speeddoes not clear the flue,the
pressure detector will shut off the gas supply.
If the flames go out, or if for any reason the fire is turned off when hot, always wait at least 3
minutes before attempting to relight.
If this device starts to shut off the gas frequently please get expert advice.
This device is NOT a substitute for an independently mounted Carbon Monoxide detector.
GAS CONSUMPTION
Natural Gas models have a maximum gas input of 6.0kW (Gross) and a minimum gas input at
the low setting of 2.2kW (gross).
Propane Gas models have a maximum gas input of 6.1kW (Gross) and a minimum gas input at
the low setting of 3.6kW (gross).

6
66
6
CLEANING YOUR GAS FIRE
To maintain the high performance and quality finish of your fire, please follow these guidelines:
•Before attempting to clean the fire,please remember to turnoff the gas at the fire andthe
electricity at the isolating switch.
•Wait for the appliance to cool. The fire will retain heat for some time before cleaning can
begin.
Metal Parts
Clean the metal parts with a slightly damp cloth and then dry.
Do not use abrasive cleaners as these will scratch the fire surface.
Coals and burner compartment rear wall
This product uses fuel effect pieces and a burner compartment rear wall containing Refractory
Ceramic Fibres (RCF), which are man-made vitreous silicate fibres. Excessive exposure to this
materialmay cause temporary irritationto eyes, skinand respiratory tract. Consequently,it
makes sense to take care when handling these articles to ensure that the release of dust is kept to
a minimum.
Light coatings of soot will usually be burnt off during the normal operation of the fire. Should
any soot accumulation become excessive,the fuel effect pieces andwalls shouldbe removed
from the fire for cleaning. Cleaning should be carried out in a well ventilated area or in the open
air by gently brushing with the pieces held away from your face so that you avoid inhaling the
dust. We do not recommend the use of a normal domestic vacuum cleaner which may blow dust
back into the air.We suggest that you remove the coals in the reverse order to that shown inthe
fuel bed refitting instructions.
Ceramic burner
Remove any deposits of soot or otherforeignmatter fromthe solid areas ofthe burnerwith a dry
soft brush. Be careful not to brush any particles into the open slots. Remove any particles from
the slots with a vacuum cleaner fitted with a soft brush attachment. Do not poke wire, etc. into the
slots in the burner.
Flue terminal
Keep the slots in the flue terminal onthe outside wall clear of any obstructions (leaves, snow
etc.)
Ventilation
If any purpose made ventilation was provided for this appliance, make sure that it is always free
from any obstruction.
Flue ducts (Side flue models)
The flue duct covers running along the wall can be cleaned with a slightly damp cloth
and then dried.
The coversin front of the duct pipes and the metalbacking covers next to the wall
can be painted, if necessary, with any of the widely available primer and finishing
paints suitable for metal surfaces.
The space behind the top back edge of the duct front covers must not be blocked (See
figure 4). The space is to allow cooling air to circulate along the ducting run.
PART 3: MAINTENANCE
Figure 4 Duct air gap

7
77
7
FUEL BED REFITTING
If the fuel bedcomponents are dislodged or removed,they must be refitted as follows:
Only the fuel bed parts supplied with this appliance or authorised Wonderfire replacements must be used. Never add extra coals above the
number stated in these instructions.
1With its feather edge at
the top,place the ceramic
rear wall into the channel at
the back of the firebox. Push
the wall flat against the rear
of the fire box. (See figure
5).
2Place the front
base coal in the burner
compartment so that it
rests on the ledges at
the sides and front.
Pull the coal forward
so that it is
immediately behind
the front rim of the
burner compartment.
(See figure 6).
3Place the rear
base coal in the burner
compartment behind
the front coal. It should
rest on the ledge at the
back of the burner
compartment and its rear
face should touch the rear
ceramic wall (See figure 7)
4Install the 9 loose coals
as follows. The smooth
surfaces of the coals should
be at the bottom andback.
4.1 Select the two smallest
coals and put them aside
until all the other coals are
installed.
Place four of the medium
size coals in the four valleys
of the front coal. Place the
left side coal so that the pilot
flame will be visible. (See
figure 8).
4.2 Place the three
remaining medium size
coals behind and
approximately midway
between each of the coals
in the front row (See
figure 9).
4.3 Place the two
remaining small coals
alongside the main coals (See
figure 10)
Fig 10 Small side coals
Fig. 9 Middle row of coals
Fig. 7 Rear base coal installation
Fig. 8 Front row of coals
Fig. 6 Front base coal
installation
Fig. 5 Ceramic rear wall
installation

8
88
8
GENERAL SERVICING
Regular maintenance
In order to achieve and maintain high levels of personal safety and performance efficiency, it is
essential that the opening at the back of the fire and the flue are kept clear of any form of
obstruction. It is possible that deposits of mortar or soot could fall and accumulate causing the
flue to be blockedor restricted and so preventing proper clearance of dangerous exhaust fumes.
In the United Kingdom it is the law that a landlord must have any gas appliance, flue and
pipework which is situated in a tenant’s premises checked for safety at least every twelve months
by a competent person (In the U.K, a CORGI registered installer).
Servicing
•In the United Kingdomservicing can be carried out either by a Wonderfire Service engineer
or a CORGI registered installer.
•If you require your fire to be serviced, please contact the Wonderfire service department
on 0121 386 6203 and quote the following details;
a) - model name and number.
b) - appliance serial no. (To be foundon a plate tied below the burner and behind the bottom
front cover)
•If you wish to replace any of the owner replaceable parts listed below,please contact your
dealer or the Wonderfire service department for your nearest stockist of these parts. When
orderingplease quote the part number shown below.
•In Republic of Ireland call 353 183 75114 for all enquiries.
Description Part No
Rear wall 545999
Front base coal 9770074
Rear base coal 569459
Pack of 9 top coals 9780033
When fitting replacement parts, follow the instructions contained in this guide. It is important
that only Wonderfire approved parts are used for maximumsafety.

All Wonderfire appliances are CE Approved and designed to meet the appropriate British Standards.
All Wonderfire appliances are manufactured to the highest standards of quality and excellence under the BS
EN ISO 9001 quality system accepted by the British Standards Institute.
All Wonderfire gas appliances must be installed by a competent person in accordance with the Installer
Guide. If in doubt always use the services of a CORGI Registered Installer
Please fill in the following information for your own future reference. The information should always be
quoted in any correspondence with your original supplier or
Wonderfire service department.
In the United Kingdom please telephone [phone].
Inthe Republicof Irelandpleasetelephone353 183 75114
Model BR517R
Front Lincoln
Supplier’s Name
Supplier’s Address
Telephone No.
Date of Purchase
Guarantee Card No.
MANUFACTURED BY WONDERFIRE
Wood Lane, Erdington, Birmingham B24 9QP
Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication
© Wonderfire