Woodshaw BRANTHAM User manual

70mm
x2
70mm
x10
150mm
110mm
x2
x2
x4
x4
W
C R A F T E D F O R Y O U R O U T D O O R S P A C E
O
O
D
S
H
A
W
620002
BRANTHAM 2 SEATER HAMMOCK
ASSEMBLY INSTRUCTIONS
Contents
Fixings
Components
Tools Required
(A) x1 Seat
(B) x1 Back
(C) x2 Arm (1xL/1xR)
(D) x1 Toprail
Before you start:
Clear an area to build the product.
Identify parts and lay them out ready.
2 persons advised for assembly.
Site product on a clear level area.
�
�
�
�
�
Only fully tighten when all components are aligned in place
Helpline 01302 761573 Monday to Friday 9am - 5pm
(1) 2x 1120mm Chain
(2) 2x 980mm Chain
Pozi Drive Screwdriver
13mm Socket or Box Spanner
1
(3) 4x Carabine Clip
(E) x4 Frame Leg (2xL/2xR)
(4) 4x Corner Bracket
(5) 4x 50mm Hex Bolt
(6) 2x 100mm J Bolt
(7) 2x 150mm Eyebolt
(8) 2x 110mm Eyebolt
(9) 2x 90mm Allen Screw
(10) 4x 90mm Coach Bolt
(11) 2x 65mm Coach Bolt
(12) 8x 50mm Coach Bolt
(13) 16x 25mm Woodscrew
(14) 36x 40mm Woodscrew
(15) 14x 70mm Woodscrew
(16) 2x Nyloc Nut
(17) 22x Hex Nut
(18) 24x Washer
(F) x2 Leg Sidreail
(G) x1 Bottom Rail
(H) x2 Brace (1xL/1xR)
(I) x2 Canopy Siderail
(J) x16 Canopy Slat
Allen Key (supplied)
2
(A)
(B)
(C)
(K) x1 Canopy Bearer
110mm
150mm
(C)
(C)
(C)
110mm
150mm

x4
x4
x2
100mm
50mm
x6
x4
x2
(Nyloc)
x8
50mm
x8
x8
x2
x2
x2
x2
90mm
65mm
*Bolt-heads inside
countersinks
Helpline 01302 761573 Monday to Friday 9am - 5pm
3
4
5
*Nyloc Nuts for J-Bolts
Leave loose to attach chains in step
(D)
(E)
(E)
(E)
(E)
(F)
(F)
(G)
*Countersink holes
facing outside
7

40mm
x32
x4
x4
x4
x2
x4
90mm
70mm
40mm
1120mm
x2
x2
980mm
x4
Helpline 01302 761573 Monday to Friday 9am - 5pm
6
7
8
40mm
70mm
Repeat step at opposite end of frame assembly
6
(H)
(I)
(J)
980mm
1120mm
Fully tighten J-bolts after attaching chains

x16
25mm
620002
W
C R A F T E D F O R Y O U R O U T D O O R S P A C E
O
O
D
S
H
A
W
Care and Maintenance
This is a natural product and therefore colour may vary
slightly from piece to piece. As a natural product it is
possible that knots can work loose and sometimes fall
out, also resin leakage and small cracks can appear on
the woods surface. Should this happen, clean off resin,
ensure any sharp edges are sanded smooth and recoat.
Products should be given suitable protection from adverse
weather conditions, particularly during the winter months.
Please retain these instructions for future reference and use.
Product should be checked regularly, and re-coated
with a suitable topcoat finish when required. If
accidental damage occurs, lightly sand and re-coat
with a suitable water based wood preservative.
Product can be cleaned periodically with a mild
soapy detergent.
Your new garden item is a natural timber product. In order that you may prolong the life of
this product, we recommend that you follow the general care and maintenance advice below.
All fixings to be checked for tightness and signs of deterioration at the beginning of each season
and on a regular basis. We recommend that this product is positioned on firm level ground. If
necessary the product can be firmly fixed to the ground by using a proprietary ground anchor.
The timber used in the product is pressure treated in accordance with BS 8417:2011 to provide
protection against biodeterioration in end use situations. It is possible that under some environmental
conditions that a surface mould may develop, should this happen clean off with mild soapy water.
9
(K)