Workhorse Products Wash-It User manual

Owner’s Manual
WASH-IT
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 1
67-1420 REV 418

Table of Contents
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 2
I. Introducon & Features……………...……………………………………….…………………………………3
II. Parts for Assembly…….……………………………………………………………………………………………4
III. Assembly…………………………………………..……………………………………………………………….….5
IV. Limited Warranty……………..…………………………………………………………………………………….9

Introducon & Features
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 3
Congratulaons on your purchase of the Wash-It Screen Wash Out/Reclaim Sink. We’d like
to thank you for choosing Workhorse Products!
Please check the contents of the packaging for damages immediately. While our packaging has been
designed to handle normal shipping condions, we cannot foresee damages caused by the carrier and are
not responsible for damages that occur during transportaon.
If shipping damage has occurred, immediately contact the carrier to le a claim and contact Workhorse
Products at 800-778-8779.
The Importance of the Owner’s Manual:
The purpose of the Owner’s Manual is to familiarize you with the parts and operaons of the Wash-It. There
are step-by-step instrucons to set up this equipment as well as addional informaon that will help with
the operaon and maintenance.
• Ideal for small to medium sized printers.
• Sturdy construcon.
• Translucent back splash.
• Large screen capacity.
• Waterproof welded seams.
• Adjustable screen tray.
• Standard plumbing ng.
• Complete draining.
• Easy to assemble.
Features

Parts for Assembly
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 4
Carton Contents
A -Two side splash panels
B -One top splash panel
C -Two screen stops
D –Fastener bag
E -Four wash sink legs
F -One back leg brace and two side leg
braces
G- One sink base
H- One Polypropylene back panel
H
G
F
E
C
D
B
A
4 Leg leveling feet
1/2” Nuts
1/2” Washers
1/2" Bolts
Silicone sealant

3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 5
Assembly
Start with the four leveling feet. Screw the jam nut down
unl it contacts the top of the foot.
Screw the leveling feet into the boom of the legs, as
shown.
Remove the translucent back splash panel from the Wash-It
sink base.
Aer installing the leveling feet to the legs, invert the
wash sink base. Place one of the legs in a corner of the
wash base with the smooth side facing out as shown.
Loosely fasten the leg using a bolt, lock washer and nut.

3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 6
Loosely fasten the rest of the legs as shown.
Loosely fasten the leg braces between the two back
legs and two front legs with the smooth side facing
out using four bolts, washers, and nuts.
When all of the bolts, lock washers and nuts are in
place securely ghten using a 1/2” wrench.
Place the Wash-It sink base and leg assembly on the
oor.
Install one of the two side splash panels into the
Wash-It sink base corner. The shorter side of the
L shaped panel faces the center of the Wash-It sink.
Loosely fasten with bolts, lock washers, and nuts.
and put it into one of the corners.
Assembly

Assembly
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 7
Aach the opposite side splash panel in the same manner.
Aer installing both side splash panels, insert the translucent
back splash panel into the slots provided. Ensure the back
panel is inserted unl it contacts the lip on the Wash-It sink
base. Note that the double wide Wash-It sink is supplied
with two translucent back splash panels.
Securely ghten all fasteners using a 1/2” wrench.
Install the top splash panel. The lip on the top panel faces up
and should be on the rear of the Wash-it sink as shown.
Align the bolt holes and insert three bolts on each side.
Loosely fasten the bolts unl all are installed, then securely
ghten using a 1/2” wrench.

Assembly
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 8
Aer assembling the Wash-It sink,
seal all bolts and seams from the
inside of the sink using the
provided silicone sealant.
Locate the Wash-It sink in the desired locaon.
Workhorse Products recommends that the
drain connecons be made by a licensed
plumber.
OPTIONAL SQUEEGEE RACK
You can add this handy rack to your Wash-It
sink! The rack hangs on the inside of the sink
and holds up to 8 squeegees.

Limited Warranty
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 9
Although every eort has been made to provide accurate specicaons, Workhorse Products does not assume any liability
for damages, whether consequenal or incidental, that may result from the use or misuse of the indicated specicaons.
Workhorse Products requires the use of a licensed industrial electrician for the installaon of electrical service to
equipment requiring electrical power.
Workhorse Products reserves the right to alter specicaons in the manufacture of its products. It is understood and agreed
that Seller’s liability for any equipment whether liability in contract, in tort, under any warranty, in negligence, in strict liability
or otherwise shall not exceed the return of the amount of the purchase price paid by Buyer. Not withstanding the foregoing
provision, under no circumstances shall Seller be liable for special, indirect or consequenal damages. The price stated for the
equipment is a consideraon in liming Seller’s liability. No acon regardless of form, arising out of the transacons under
this Agreement may be brought by Buyer more than one (1) year aer the cause of acon has occurred. Our warranty is
specied is exclusive and no other warranty, whether wrien or oral, is expressed or implied. Workhorse Products specically
disclaims the implied warranes of merchantability and tness for a parcular purpose. Equipment manufactured or sold by
Workhorse Products is warranted against defects in workmanship and materials for a period of one year from receipt by
customer. All warranes iniate from date of shipment to original customer. Replacement parts are covered for the term of
the equipment warranty period. Parts not under warranty are covered for thirty (30) days from receipt by customer. Any
part found by Workhorse Products to be defecve in material or workmanship within the stated warranty period will be
replaced or repaired at Workhorse’s opon without charge.
AFTER OBTAINING AN RMA# SEND RETURNED FREIGHT PREPAID TO 3730 E. Southern Avenue, PHOENIX, AZ 85040 USA.
Wrien authorizaon must be obtained from Workhorse before any part will be accepted. Replacement parts are sent out
freight collect.
Parts sent out prior to receiving defecve require a credit card hold for cost plus freight. Upon return of defecve part, if it
is deemed that the part was not damaged by customer but failed, the cost of the replacement part will be refunded.
This warranty does not extend to expendable parts such as lters, fuses, elements and brushes. Workhorse does not
warrant failure of parts or components resulng from misuse or lack of proper maintenance. Installaon, inspecon, and
maintenance costs are the sole responsibility of the purchaser.