Worldtag Fashion Series User manual

FASHIONPLUS ERGONOMIC CHAIR
INSTRUCTION MANUAL
VERSION NO- 01 DEC 2014
Five Star Chair Base 1 pc
Twin walled Castors 5 pcs
Center Pillar 1 pc
Telescopic dust cover 1 set (3 pcs)
Hardware
1.5" button screws 6 pcs
1" button screws 4 pcs
6mm washers 10 pcs
8mm washers 10 pcs
Allen key small 1 pc
Spring Washers 3 pcs
Allen key screws 3 pcs
Allen key big 1 pc
1/4' buffers 4 pcs
1/2" buffer 4 pcs
Plastic Lever 1 pc
Mechanism 1 pc
Handles 2 pcs (left/right)
Back Rest 1 pc
Cushioned Seat 1 pc
PACKING LIST FOR
WORLDTAG FASHION CHAIR

1
Reverse the chair base and place on the floor
Push fit castors into each of
the five arms of the chair base.
Turn the chair base over
2
1
3
4
Prepare the set of telescopic dust
cover by inserting the smallest
dust over into the bigger one and
that into the biggest dust cover
with the narrow part towards
bottom and broader part upwards.
2
Insert the center pillar into the hole
in the middle ofthe chair base.
6
5
Overturn the dust cover and
insert on the pillar so as to
cover the full pillar when
pulled up.
Five pronged base is ready
to assemble with upper
assembly of chair. Keep this
aside and start preparing
upper assembly of chair.

10
11
12
Place the mechanism so that
the four holes on the
mechanism are aligned with
the remaining 4 holes in the
seat with the cap with 3
holes for the back rest is
towards the rounded back
area and vertical pillar being
in the center.
Insert the 6mm plain washer followed by the 8mm plain washer into
the M6*35 screw and M6*25 screws. Insert theM6*35 screws in the 2
holes at the front side and M6*25 screws at the back side of the
mechanism. Tighten all 4 screws with the small allen key.
Place the 8mm thick
2 nos buffers each in the
2 holes towards the
broader end of the seat.
4
3
Place the 6mm thick
plastic buffers in the 2 holes
to the side of the seat.
Place the handle marked right
to the right side of the seat
and vice versa
Allen key
6mm
M 6X25 M6X50
M6X50
Cut washer 6mm
Plain washer 6mm
8
7
9
Place the handle on the seat so
that the two outside holes are
aligned with the buffers and
holes. Insert the 6mm cut
washer followed by the 6mm
plain washer into the M6*50
screws. Insert the screws and
tighten slightly.
Place the seat on the table
with broader edge to the
front and mark left and
right and then reverse.
M 6x35x2 nos at front
Plain washer
8mm
Plain washer
6mm M 6x25x2 nos
at back
Plain washer
6mm
Plain washer
8mm
Allen key 6mm
R
L
Insert the 6mm cut washer
followed by the 6mm plain
washer into the M6*25 screw.
Insert the screw in the third
hole in the handle aligned with
the third hole in the seat and
tighten all 3 with the small
allen key.

M8x20x3nos
at back
Cut washer
8mm
Plain washer
8mm
14
15
Insert the 8mm cut and 8mm plain
washers into the allen key M8*20
screws and insert the screws into
the holes and tighten lighten with
the big allen key. The Chair’s
upper assembly is ready to fit
assemble with on the five pronged
prolonged base.
Slide the backrest into the
cap of mechanism and align
the three holes.
Push insert the plastic
lever into the metal pin
of the mechanism.
13
Your Fashionably
Fashionplus
Ergonomic chair
is now ready for action!!
16
Lift the seat, turn
and place into the
shaft of the center
pillar attached to
the chair base.
6
5
Allen key 8mm

1
2
Tilting the plastic lever will allow you
to adjust the height of the chair
according to your convenience.
Note: To raise the height of the chair
do not do so while sitting on the
chair.
Pushing the lever
inward or outward will
lock or unlock the back
rest for back support
while working or
lounging.
Note: While pushing
the lever inward or
outward, the back
should be bent forward
and not resting on the
back rest.
Press the button on
the inside of the
armrest to pull
upward or downward
to change the height
of the armrest.
Pull the
flap out.
Pull the
zipper
upward.
Pull mesh
upwards.
8
7
FUNCTIONS HOW TO CHANGE
THE ZIP-ON ZIP-OFF
MESH

10
9
4
Insert new
mesh.
3
Mesh
removed.
Pull the ends of the
zipper outward.
Pull the zippers
down.
5
Viola, Your
Fashionplus chair is
NEW once again!!!
7
Turn the flap
inside and
press it.
6