WOVEN IMAGE ECHOPANEL ELEMENT User manual

ECHOPANEL® ELEMENT
(Blades & Ceiling/Wall clips)
INSTALLATION GUIDE
For product specications please visit wovenimage.com
This guide is presented in good faith to assist in the
installation of ceiling grids. It is not intended as an
all-encompassing guide, and a professional qualied
installer is recommended for optimum results.
Woven Image accepts no responsibility for installation
actions taken or not taken. Please refer to Woven Image
Pty Ltd. Terms of Trade.
This installation guide contains only recommendations;
if you have any questions about installation techniques
please contact your distributor or Woven Image sales
representative.
Please return all unused parts to Woven Image for
recycling, thank you.
Please note:
• Please check that all ceiling blades are the correct
colour, shape and same batch number (if requested).
• No claims will be accepted after EchoPanel® Element has
been installed.
• The clips should be tested for ceiling suitability and type
of xing required.
• All surfaces must be smooth, clean, dry, dust and
mould free.
• The clips supplied are appropriate for the installation of
one EchoPanel® Element kit.
SPECIFICATION
• Non-woven PET acoustic ceiling blades
• Recyclable ABS ceiling and wall clips for 24mm
EchoPanel® blades
• Suitable for direct x to wall or ceiling, or mounted to
standard ceiling grids
• Translucent nish
• 2350mm x 215mm x 24mm per blade
BOX CONTENTS
• 8 x EchoPanel® blades per box, to form one grid
(sold by the box only)
• 8 x Panel clips
• 8 x Track clips
• 8 x Washers
• 8 x E-clips
• Installation guide
Track clip
Panel clip
E-clip
Washer

ECHOPANEL® ELEMENT
(Blades & Ceiling/Wall clips)
INSTALLATION GUIDE
For product specications please visit wovenimage.com
There are two methods of assembly
for the provided clips. This will
depend if you are attaching to a
ceiling grid system or direct xing to
a ceiling or wall.
Ceiling grid method:
Step 1
• For ceiling grid use, assemble track
clip and panel clip using one e-clip.
• Gently press the sides of the track
clip inwards, whilst pushing the clip
up against the ceiling grid, until it
clicks into position.
• Rotate the panel clip to suit
direction of EchoPanel®.
• Use the provided diagram to space
the clips on a standard ceiling grid.
Ceiling grid
Direct x
600mm
600mm
600mm
600mm
600mm
1200mm 1200mm
470mm between clips
1200mm

ECHOPANEL® ELEMENT
(Blades & Ceiling/Wall clips)
INSTALLATION GUIDE
For product specications please visit wovenimage.com
Step 3
• Slot top and bottom blades together
forming a square grid.
Step 2
• When all the clips are xed, you will
have a grid of clips ready to install
the blades.
Step 4
• Push EchoPanel® Element into the
clips, making sure all 16 clips are
holding the structure.
• The clips supplied are appropriate
for the installation of one
EchoPanel® Element kit.

ECHOPANEL® ELEMENT
(Blades & Ceiling/Wall clips)
INSTALLATION GUIDE
For product specications please visit wovenimage.com
Direct x method:
• For direct x to a ceiling or wall,
select only the panel clip and
washer.
• Using the clips spacing diagram
from the grid install, mark out the
placement of the clips.
• Prepare the wall or ceiling surface,
installing appropriate wall plugs if
needed.
• Use a screwdriver to x the panel
clip directly to the surface, using
the washer provided.
• Rotate the panel clip to suit
direction of EchoPanel®.
Panel clip
Washer
24mm blade
ABS clip
EchoPanel® Element shown
completed on a standard ceiling

For product specications please visit wovenimage.com
BOX CONTENTS
• 4 x Ceiling xtures
• 4 x Steel cables (2 metres long each)
• Installation guide
SPECIFICATION
• Add-on Suspension kit to be used with EchoPanel®
Element
• Maximum suspension length of 2 metres
ECHOPANEL® ELEMENT
(Suspension kit)
INSTALLATION GUIDE

For product specications please visit wovenimage.com
ECHOPANEL® ELEMENT
(Suspension kit)
INSTALLATION GUIDE
Step 1
• Reected ceiling elevation -
placement and spacing of
ceiling clips.
Ceiling xture with adjustable
cable stopper
2 metre steel cable
Aluminum cable end
245mm
600mm
600mm
600mm
245mm
470mm between clips

For product specications please visit wovenimage.com
ECHOPANEL® ELEMENT
(Suspension kit)
INSTALLATION GUIDE
Step 2
• Undo the top section of the
ceiling xture and screw x it
to the ceiling.
• Then re-assemble the xture.
Step 3
• Feed the cable through the ceiling
xture, by undoing and pushing the
bottom part of the xture.
• Adjust the length of the cable,
tighten the xture, then trim excess
cable.
Feed the cable through
the washer and through
the Panel clip.

For product specications please visit wovenimage.com
ECHOPANEL® ELEMENT
(Suspension kit)
INSTALLATION GUIDE
Step 4
• When all the xtures have been
installed, you will have a grid of
cables and clips ready to install
EchoPanel® Element.
• Ensure all the cables have been
adjusted to the desired length.
Step 5
• Assemble EchoPanel® Element
as per Installation guide at the
beginning of this document.
• Push EchoPanel® Element into the
clips, making sure all 16 clips are
holding the structure.
• 4 x 24mm Suspension kits are
appropriate for the installation of
one EchoPanel® Element.