WTA QTY-1 User manual


WTA
Installation Guide
Sprinter Side Ladder
ItiscrucialtoensurethatallWTAproductsareassembled
andsecurelyattachedtoyourvehicle.Failuretodosomay
resultinautomobileaccidents,posingasignificantriskof
bodilyinjuryorevendeathtoyourselfandothers.Asthe
owner,itisyourresponsibilitytoproperlyassembleand
secureWTAproducts,diligentlyinspectingthemounting
pointsandattachmentsbeforeuse,andregularlychecking
foranysignsofwearordamage.

Toguaranteeoptimalsafety,westronglyadviseengaging
theservicesofaprofessionalinstallerfortheinstallationof
anyaftermarketaccessoriestoyourvehicle.Ifyoulack
mechanicalexperienceorareunfamiliarwiththeinstallation
procedures,itisimperativetohavetheproductinstalledby
aqualifiedprofessionalorindividualswhopossessthe
necessaryexpertise.Remember,theresponsibilitylieswith
you,anditmustbetakenseriouslytoensurethesafetyofall
individualsinvolved.

3

PACKAGE CONTENTS
LADDER BOTTOM
QTY-1
MOUNT PLATE
QTY-1
RAILNUT
QTY‐2

LADDER TOP
QTY-1
M6-16 BUTTON HEAD SCREW
QTY-4
M6-30 HEXGON HEAD
SCREW QTY-4
M6 FLAT WASHER
QTY-8
M6 NYLOCK NUT
QTY-4
M10-22 HEXGON HEAD SCREW
QTY-2
M10 SPRING LOCK WASHER
QTY-2
M10 FLAT WASHER
QTY-4
M10-30 HEXGON HEAD SCREW
QTY-2
M10 NYLOCK NUT
QTY-2

4

FIGURE1
LET’S GET STARTED!
1. PLACETHELADDERHALVESFRONTSIDEDOWN,INSERTTHECOUPLERSINTOONEHALF(SEE
FIGURE1),ANDTIGHTENDOWNUSINGTHEM6‐16
SCREWS.


2. SLIDETHEOTHERLADDERHALFONTOTHECOUPLERSANDTIGHTENDOWN. NOTE‐IF
DESIRED YOU CAN USE BLUE LOCTITE ON THE SCREWS.
FIGURE2


5


3. NEXT,SLIDETHETWO(2)RAILNUTSINTOTHEROOFRAILONYOURVAN.NOTE- IFYOU’VE
ALREADYINSTALLEDAROOFRACK,THISMAYBETIMECONSUMING.

4. NOWPOSITIONTHELADDERONTHEVAN,HANGINGITONTHEROOFRAIL.LOOSELY SCREW
THE TOP OF THE LADDER DOWN TO THE ROOF RAIL USING THE M10-22 SCREWS
AND THE M10 SPRING LOCK WASHERS AND M10 FLAT WASHERS JUST ENOUGH
THAT IT IS SNUG (SEE FIGURE 3)
NOTE- WE LIKE TO PLACE THE LADDER AS CLOSE TO THE REAR
WHEEL WELL AS WE CAN. SEE IMAGE BELOW.
RAILNUT













FIGURE3

 


6
5. TAKETHEMOUNTPLATE(SEERIGHT)AND
LOOSELYATTACHTHEMTOTHEBOTTOMOFTHELADDERUSINGTHEM10‐30SCREWS,
M10FLATWASHERS,ANDM10NYLOCKNUTS.
NOTE‐MAKE SURE THAT THE LADDER IS STRAIGHT UP AND DOWN.
6. Lineupthesupportplatewiththeladderanddrill5holeswith¼inches
drillbit.
7. SupporttheplateontothepinchweldwithM6boltandnuts.
8. SupporttheladdertothesupportplateusingM10‐30boltsandnuts.
MOUNTPLATE