X-TINGUISH X-TREME User manual
1
REV 3.210
OPERATION MANUAL
X-TINGUISH® X-TREME
AEROSOL FIRE SUPPRESSION TOOL
2
CONTENTS
THANK YOU FOR YOUR PURCHASE! 3
HOW THE X-Tinguish® X-TREME WORKS 4
HOW IT WORKS 4
BEFORE USING THE X-Tinguish® X-TREME 5
WHO SHOULD USE THE X-Tinguish® X-TREME 5
INSPECTIONS 5
STORAGE 5
DEPLOYING THE X-Tinguish® X-TREME 5
PREPARING FOR DEPLOYMENT 5
X-Tinguish® X-TREME QUICK START GUIDE WITH GRAPHICS 6
DEPLOYING THE X-TINGUISH X-TREME 7
AFTER USING THE X-TINGUISH X-TREME 8
IN THE AFFECTED AREA 8
FIREFIGHTER /FIRST RESPONDER NOTE 8
WARNINGS AND GUIDELINES 9
ENVIRONMENTAL 9
CLEAN-UP AFTER DEPLOYMENT 9
FIRST AID PROCEDURES 10
EYE CONTACT 10
SKIN CONTACT 10
INGESTION 10
INHALATION 10
LIMITED WARRANTY 11
CONTACT INFORMATION 12
3
THANK YOU FOR YOUR PURCHASE!
Thank you for purchasing the X-TINGUISH® X-TREME, the most
efficient and advanced aerosol fire suppression tool on the market
today.
Correct and timely usage of the X-TINGUISH® X-TREME can prevent
and / or significantly reduce the damage caused by fires. Additionally,
the X-TINGUISH® X-TREME allows its user the ability to mitigate
the danger posed by flash-over and back-draft to firefighters and first
responders. While no device portable device can prevent or totally
suppress the harmful effects of a fire, the X-TINGUISH® X-TREME is a
unique way to combat fires and represents a giant advance in fire-
suppression technology from water or other chemical-based methods.
The X-TINGUISH® X-TREME is a small, portable unit that contains
potassium based chemical components. It is designed to be a
first-use method to combat class A, B, C, and K fires. When the
device is deployed at the scene of a fire, the X-TINGUISH® X-TREME
releases a cloud of aerosol containing the potassium components,
interrupting the chain reaction in the flame.
When utilized and deployed according to the instructions in this Op-
eration Manual, it provides an effective method of fire suppression
that minimizes the risks posed by more traditional methods of fire-
fighting.
Please use this Operation Manual a s the source of information for
storing, using, and disposing of the X-TINGUISH® X-TREME
FLAME GUARD USA 2020
4
HOW THE X-TINGUISH® X-TREME WORKS
HOW IT WORKS
The X-TINGUISH® X-TREME is a portable fire suppression device. It is not a fire
extinguisher and not intended to replace any fire extinguishers that are required by
NFPA 10 or USCG regulations. The unit consists of a steel housing containing chemical
agents that form the aerosol, separated by an insulating barrier; a handle for ease of
transportation and deployment and a securing pin and an igniter pin that is used to
activate the X-TINGUISH® X-TREME electronically.
The X-TINGUISH® X-TREME is an active fire suppression system utilizing an
environmentally safe, condensed aerosol that, when deployed, has the appearance of
smoke.
When the unit is deployed and its aerosol is released, the aerosol drastically reduces
the temperature of the room immediately(by up to 1,000°F in less than 1 minute in
most cases). The aerosol absorbs the fires energy interrupting the thermal activity
from the chemical reaction taking place without removing oxygen from the enclosure.
The X-TINGUISH® X-TREME is significantly different from CO2, dry chemical, and water-
based fire prevention systems. Its condensed aerosol (SFE) Works simultaneously on
the fire tetrahedron (heat, fuel and the fire’s chemical reaction) without affecting
oxygen levels. When used in accordance with these instructions, deployment of the
X-TINGUISH® X-TREME poses no risk to occupants and first responders and will
effectively minimize any of the fires collateral and environmental damage.
The device inhibits the fire from obtaining the oxygen radicals it needs to continue
burning and spreading further. Once activated by the user, the potassium based
compounds (called S.F.E.) of the X-Tinguish® are heated, turning the solid compounds
into an aerosol that can spread rapidly throughout the area containing fire.
One X-TINGUISH® X-TREME generally can effectively suppress a fire in a room that
measures up to 5,300CU.FT. ,(if the room does not have any greatly open spaces).
Once deployed, the device discharges its aerosol for approximately 30 seconds. The
unit’s aerosol can remain suspended for up to 45 minutes, depending on how
enclosed the room is.
You should immediately see results in the flames of the fire as the X-TREME’s aerosol
interrupts the chemical reaction of the fire, stopping completely or greatly slowing the
rate at which the structure and/or contents burn.
The use of the X-TINGUISH® X-TREME will lower the temperature in the affected space
by literally hundreds of degrees in less than 1 minute, making it safer and easier for
trained firefighting personnel and first responders to control the spread of the fire.
5
BEFORE USING THE X-TINGUISH® X-TREME
WHO SHOULD USE THE X-TINGUISH® X-TREME
Only those personnel who are trained and are familiar with the operation of the
X-TINGUISH® X-TREME or its predecessor the X-Tinguish® FST should use it. All
operators should read and understand this Operation Manual prior to use.
INSPECTIONS
All X-TINGUISH® X-TREME units should receive an inspection once per year and a
replacement of batteries once every five years. All batteries can be replaced by the
owner. YOU MUST ONLY USE ORIGINAL BATTERY PACKS PROVIDED BY YOUR
DISTRIBUTOR OR THE COMPANY YOU PURCHASED YOUR UNIT FROM. IF YOU NEED
ASSISTANCE, PLEASE CALL (855) 377-2100 TO INQUIRE ABOUT NEW BATTERIES FOR
YOUR FST UNIT. Inspectors should make sure that the X-TINGUISH® X-TREME is not
damaged in any way and there is no evidence of use or deployment.
Never try to disassemble the X-TINGUISH® X-TREME. If you try to disassemble the
X-TINGUISH® X-TREME and you alter the unit, you will break the unit and it
will remain unrepairable and not covered under any warranty. ALWAYS leave
the protective R-Pin in place until it has been determined the device is required
to fight a fire. If the device has been damaged in any way, it should not
be deployed. Should the Igniter pin and ring become detached accidentally from
the unit, immediately throw the unit away from yourself and any person in
the vicinity. At this point, the 8 second countdown until ignition has begun
and CANNOT be reset. The unit will deploy its aerosol after the 8 second countdown.
STORAGE Keep the X-TINGUISH® X-TREME in its original case whenever possible
and store it in a place that is not exposed to extreme heat or humidity. Avoid
contact with heat, sparks, flames, and other heat sources. Do not drill, solder or
cut the unit. Keep it away from oxidizing agents, strong acids and strong bases. The
X-TINGUISH® X-TREME will normally be safe for its intended use for a period of 15
years when stored properly. Once every five years the unit’s battery must be replaced.
DEPLOYING THE X-TINGUISH® X-TREME
PREPARING FOR DEPLOYMENT
All first responders should assess the situation and make a determination as to
whether to use the X-TINGUISH® X-TREME. Since every fire is different, first
responders should use their judgment as to where and when to deploy the
X-TINGUISH® X-TREME. The X-TINGUISH® X-TREME will achieve maximum results if
the fire room is enclosed and is deployed near the seat of the fire.
Announce to any fire personnel or bystanders that the X-TINGUISH® X-TREME is
being de-ployed and advise them to keep a safe distance (2’ from where the unit will
land).
6
X-TINGUISH® X-TREME QUICK START GUIDE
The New X-Tinguish® X-TREME comes equipped with 2 (two)
types of metal pins. This document will explain how the New
R-Pin (2) is used in conjunction with the igniter pin (1).
The New R-Pin was added to secure the Igniter pin in-place.
Deploying the X-Tinguish® X-TREME
Evaluate the scene and decide the safest place to deploy the X-Tinguish®
X-TREME that is nearest the seat of the fire.
When the decision to deploy the X-TREME has been
made and you are in position, firmly grasp the R-
Pin and pull it straight out of the unit. Removing
the R-Pin unlocks the Igniter pin so it can be used
to deploy the X-TREME. (Picture 1)
After removing the R-Pin, firmly grasp the Igniter
Pin (1) and pull it straight out of the unit. Once the
Igniter pin has been pulled the 8 second count-
down until deployment will start and this action
cannot be stopped once initiated. You must deploy
the unit immediately after pulling the pin.
(Picture 2)
OVERHAUL AND LOOK FOR HOTSPOTS AS USUAL
5
1
2
3.
4.
Call (855) 377-2100 or email info@flameguardusa.com with any questions you may have.
Immediately throw the X-Tinguish® X-TREME into
the structure near the seat of the fire. Once the
unit is safely deployed, return to business as usual.
The unit will work independent of any human
intervention. (Picture 3)
After deploying the X-Tinguish ® X-TREME, make
sure all efforts are maintained to ensure a closed
fire room to contain the aerosol.
DO NOT VENTILATE AT THIS POINT.
Allow the X-Tinguish® X-TREME the needed time
to do its job. (Picture 4)
7
5
DEPLOYING THE X-TINGUISH® X-TREME
DEPLOYING THE X-TINGUISH X-TREME
X-TINGUISH® X-TREME aerosol will continue discharging for 30 seconds.
WARNING: IT IS VERY IMPORTANT NOT TO DISTURB THE
IGNITER PIN UNTIL YOU ARE READY TO DEPLOY THE UNIT. AFTER THE PIN
IS PULLED, IMMEDIATELY THROW THE FST UNIT INTO THE FIRE. THE
X-TINGUISH® X-TREME WILL AUTOMATICALLY ACTIVATE 8 SECONDS AFTER
THE PIN IS PULLED. THIS PROCESS CANNOT BE STOPPED ONCE THE YELLOW
SECURITY PIN HAS BEEN REMOVED. ONCE YOU PULL THE IGNITER PIN
YOU MUST DEPLOY THE X-TINGUISH® X-TREME INTO THE FIRE OR IF YOU
ACCIDENTALLY PULLED THE IGNITER PIN, THROW IT AWAY FROM
YOURSELF AND ANY PERSONS WITHIN THE VICINITY.
Once the Igniter pin has been pulled the device is now activated and will begin
dispersing the aerosol in 8 seconds.
After the igniter pin has been pulled, DO NOT ATTEMPT to prevent the activa-tion
of the device. Never attempt to retrieve a device that has been activated or to re-
install the yellow security pin.
Make sure that the person deploying the device can accurately throw the unit
toward the intended target location. It is best to stand or kneel when throwing the
device, aiming for level ground.
Throw the X-TINGUISHcX-TREMEat or near the base of the fire, taking care to keep
the device away from persons in the area, if possible.
After deploying the X-Tinguish ® X-TREME, make sure all efforts are maintained to
ensure a closed fire room to contain the aerosol. DO NOT VENTILATE AT THIS
POINT. Allow the X-Tinguish® X-TREME the needed time to do its job.
8
AFTER USING THE X-TINGUISH® X-TREME
CAUTION
AFTER PULLING THE IGNITER PIN - DO NOT HOLD ON TO X-TINGUISH® X-TREME ALWAYS THROW
X-TINGUISH ® X-TREME AWAY FROM YOU AND TOWARDS THE SEAT OF THE FIRE IMMEDIATELY.
IN THE AFFECTED AREA
Do not enter the treated area until the X-TINGUISH® X-TREME has discharged
completely. It is advisable to allow the aerosol adequate time to treat the fire and
dissipate before entering the space.
The area should be ventilated following use. Overhaul must be undertaken after the
X-TINGUISH® X-TREME device has been utilized to eliminate any hotspots
that could be remaining.
Those personnel who enter the space where a X-Tinguish® X-TREME has
been deployed should wear protective breathing gear to prevent the inhalation
of the aerosol. Treat any persons exposed to the aerosol for extended periods
of time the same as you would for mild smoke inhalation. Remove the
victim to fresh air and allow them to breathe normally. The aerosol is non-toxic
to humans and pets alike.
Follow the recommended procedures for safety, first aid, and cleanup in the
Warnings and Guidelines section of this Operation Manual.
While the X-Tinguish® X-TREME is a safe and effective method of fire suppression, it is im-
portant to always adhere the guidelines when using the X-Tinguish® X-TREME:
Firefighters or other fire prevention officials should use the
X-Tinguish® X-TREME devices only in accordance with their departments local rules or
guidelines. This Operation Manual is not intended to replace or supersede any fire
department’s standard operating procedures.
Persons who do not have experience or training in firefighting or fire prevention
should only use the X-Tinguish® X-TREME if he or she has received thorough
instructions on the use of the X-Tinguish® X-TREME. Never approach a fire or
enter a burning structure under any circumstances. Contact your local fire
department for assistance.
FIREFIGHTER NOTE: Positive Pressure Ventilation will diminish the effective con-
centrations of the aerosol. PPV will reduce the knock down time.
X-Tinguish® X-TREME devices work best in contained areas. PPV should only be
used when a fire is com-pletely knocked down and water supply is available.
It is advisable to always have one or more X-Tinguish® X-TREME devices ready for use
to avoid any delay in locating one when at a fire scene or if more than one is needed at
the fire. Do not eat or drink in the vicinity of an activated X-Tinguish® X-TREME device.
9
WARNINGS AND GUIDELINES
All personnel that may come into contact with the aerosol should wear protective
clothing, including mouth/nose covers to prevent aerosol inhalation, protective goggles,
face shield or other face protection, fireproof gloves and suitable protective
body covering. NIOSH-Approved N95 Particulate Filtering mask is acceptable.
ENVIRONMENTAL
DISPOSAL
Generally, the X-Tinguish® X-TREME units can be disposed of according to normal
disposal procedures per municipality.
GLOBAL WARMING IMPACT
The X-Tinguish® X-TREME does not pose any global warming threats. It measures
zero on both the Ozone Depletion Potential and Global Warming Potential scales.
CLEAN UP FOLLOWING DEPLOYMENT
THE X-Tinguish® X-TREME UNIT
The used X-Tinguish® X-TREME unit can be disposed of according to the normal
disposal procedures for other fire-related materials.
THE AEROSOL RESIDUE
If the aerosol leaves behind a layer of dust or lm, it can be removed with a damp
cloth or broom and dustpan. If needed, wash the aected area thoroughly with
water.
FIRE EQUIPMENT
Clean protecve clothing and other reghng equipment exposed to the aerosol in
the normal manner.
10
FIRST AID PROCEDURES
The components in the aerosol are non-toxic and are stable under normal conditions.
It is not known to be a carcinogen. Exposure to the aerosol may cause slight side
eects that should be aended to immediately.
EYE CONTACT
Exposure to the aerosol may cause slight eye irritation. Avoid rubbing the eyes.
Remove any contact lenses, lift eyelids and rinse with large amounts of water or
normal saline. If any conditions continue, consult a physician.
SKIN CONTACT
Exposure to the aerosol can cause mild skin irritation, including slight reddening of
the skin. Wash affected area with soap or mild detergent and water until no
evidence of chemical remain. If any conditions continue, consult a physician.
INGESTION
If somehow, the metal casing is opened and the product inside is ingested, the
fol-lowing is recommended. Remove by gastric lavage or emesis. Maintain blood
pressure and airway. Give oxygen if respiration is depressed. Do not perform
lavage or emesis if victim is unconscious. Get medical attention immediately.
INHALATION
Remove from exposure area to fresh air immediately. Treat the same as mild smoke
inhalaon. If condion worsens, as with any smoke inhalaon, contact a physician.
11
LIMITED WARRANTY
LIMITED WARRANTY FROM DATE OF PURCHASE AND LIMITATION OF LIABILITY
X-TINGUISH® X-TREME AEROSOL PRODUCTS ARE TO BE OPERATED ONLY BY TRAINED
PERSONNEL.
The manufacturer of the X-TINGUISH® X-TREME provides a two year limited warranty against defects in
materials and workmanship.
Limitations of Coverage: Manufacturer’s original warranty assumes use, installation, and mainte-nance in
accordance with the Product’s documentation. The warranty does not cover damage or loss of performance
due to improper installation, faulty or inappropriate preparation, abuse, vandalism, exces-sive wear and tear
or abrasion, excessive physical shock, exposure to harmful chemicals, exposure to extremes of temperature,
improper maintenance, usage by untrained personnel or any use outside those defined in the Product’s
documentation.
a) Company warrants to Distributor that the Products shall be free from defects in materials and
workmanship, in all material respects, for a period of twenty four (24) months from date of end user
purchase, when used and maintained in accordance with the Company operating and maintenance
instructions. Products deemed to be defective by Distributor should be shipped to Company for inspection.
b) Distributor's exclusive remedy for breach of warranty shall be limited to repair or
replacement (at Company’s option) of any parts found defective by Company within the warranty period.
c) The foregoing Warranty shall be void in the case of any failure to use and maintain the
Product in accordance with the Company operating and maintenance instructions, rough handling,
mechanical damage, alteration, repair not in accordance with Company instructions, or Distributor’s failure
to immediately notify Company of any defective Product.
d) The warranty sets forth the full extent of Company’s liability and is in lieu of all other
warranties or remedies, express, implied or statutory, and all other obligations or liabilities of Company,
with respect to the Products, including but not limited to, warranties of merchantability or fitness for a
purpose.
Disclaimer of Responsibility: Neither the Supplier nor its directors, officers, employees, or agents shall be held
liable for any improper or incorrect use of the Products and assume no responsibility for any-one’s use of the
Products. In no event shall the Supplier be liable for any direct, indirect, incidental, special, exemplary,
consequential or punitive damages
(including, but not limited to, personal injury or death; procurement of substitute goods or services; loss of use,
data, profits or savings; or business interruption) however caused and on any theory of liability, whether in
contract, strict liability, or tort (including negligence or otherwise) arising in any way out of the use of the Products,
even if advised of the possibility of such damage. This disclaimer of liability applies to any damages or injury,
including but not limited to those caused by any failure of performance, error, omission, interruption, deletion,
defect, delay in operation whether for breach of contract, tortuous behavior, negligence or under any other
cause of action.
Limitation on Liability: If, despite the other limitations set out above, for any reason the Supplier becomes liable
to the purchaser or any other party for damages or other liabilities incurred in connection with the Products then
the Supplier’s aggregate liability for all damages, injury, and liability incurred by the Supplier in connection with
the particular Products shall be limited to the current replacement cost of the particular Product that gives rise
to the claim for damages.
Indemnification: By taking delivery of the Products, the purchaser agrees to defend, indemnify, and hold
harmless Flame Guard USA,LLC, its contributors, any entity jointly created by them, the
irrespective affiliates and the irrespective directors, officers, employees, and agents from and against
all claims and expenses, including attorneys’ fees, arising out of the use of the Products.
Warranty.
12
Sales help: sales@flameguardusa.com
Technical help: info@flameguardusa.com
URL: https://www.flameguardusa.com
Toll-Free (855) 377-2100
Local (815) 219-4074
Fax (847) 387-3824
CONTACT US
Table of contents
