X-Trax X-360 User manual

X-TraX Group
[email protected] - www.xtrax.it
ITALY
This device is manufactured in Taiwan.
All information are subjected to change without notice.
Responsible for placing on the EU market (D. gs. 269/2001 Art. 13 / Com. 4):
X-TraX S.r.l. Via Per ecco, 24/26 - 23848 - Oggiono ( C) ITA Y
_______________________________________________________________
Manuale di Installazione X-360 (10/2019_rev.02_EN)
Installation Manual
X-TraX Group
X-360
Vehicle tracker

Attention please:
- Please strictly follow installation rules and suggestions reported into this manual.
- This device must be installed from professional and expert staff.
- In order to avoid any warranty restriction please don’t not open the housing and / or modify the
- device in any way.
- Using of this device is under the full responsibility of the installer and the user. It is therefore
- necessary to use it carefully and in full compliance with the local legislation in force.
- This device is compatible with 128K SIM Card on 2G GSM network at 900/1800MHz.
- X-TraX S.r.l. is not responsible for any damage or disservice due to inappropriate installations or
- improper use of the device.
INDEX
1. Package list
2. General description
3. Specifications
. Status LED and wiring description
5. Quick start
6. Suggestions and implementing rules
7. Directives and conformities
1. Package list
- X-360 vehicle tracker with built-in 2,4GHz radio receiver, Gemalto
- dual-band GSM/GPRS module and MTK dual-mode GPS/G ONASS receiver
- i-Ion rechargeable backup battery (1150mA/h)
- GSM antenna (wired or “ ” shape)
- GPS/G ONASS antenna
- Combined Power/Inputs/Outputs cable
2. General description
X-360 is a complete and superior vehicle tracking device which is developed
and designed for vehicle real-time tracking and monitoring purpose. It’s
suitable for different applications such as vehicle security, monitoring,
asset/fleet management.
The unit is equipped with built-in 2,4GHz RF receiver for managing dedicated
smart accessories and with RS-232 Serial port (up to 3 ports available) which
allows to interface external accessories for different utilities and services, such
as I/O expansion box.
Moreover, the unit is able to detect abnormal radio disturbance (e.g.
Jamming), reducing vehicle steals attempts.
Thanks to GPRS channel, it guarantees high level performance maintaining low
the operating costs.
X-360 vehicle tracking device, the professional choice to your location based
requirements.
7. Directives and conformities
This device is consistent and in conformity to the following International
Directives:
- EU/2002/96 Directive (RoHS)
- FCC Conformity (Federal Communications Commission)
- N° E24 10R-04.1049 Homologation
- With the essential requirements and other relevant provisions of the Directive
- RED 2014/53/EU
- Which requires as a prerequisite compliance with the Directives:
. ow Voltage Directive 2014/35/EU (to the applicable parts)
. Electromagnetic Compatibility Directive 2014/30/EU
- In conformity with the following normative European and International
- standards:
. Directive 2014/53/EU Art. 3 par. 1 / a) – Safety/Health:
EN 50385, EN 60950-1/A11, 1/A1, 1/A12, 1/A2
. Directive 2014/53/EU Art. 3 par. 1 / b) – EMC:
EN 301 489-1/19/52
. Directive 2014/53/EU Art. 3 par. 2 – Radio Spectrum:
EN 301 511, EN 303 413

6. Suggestions and implementing rules
- X-360 is a GSM/GPS vehicle tracker working by external power supply, and
- managing input & output signals. So, it must be installed from professional
- and expert staff.
- In order to get the first valid fix, it’s necessary to place the device in an
- appropriate place (open sky) avoiding any metal surface obstructing it.
- The device is not water resistant and it works in temperature environment
- from -20° to 60°. Based on this please take care of the device and use it in
- appropriate environment conditions.
- Please strictly follow implementing rules and suggestions reported into this
- manual.
- In order to avoid any warranty restriction please don’t not open the housing
- and / or modify the device in any way.
- Using of this device is under the full responsibility of the user. It is therefore
- necessary to use it carefully and in full compliance with the local legislation in
- force.
- X-TraX S.r.l. is not responsible for any damage or disservice due to
- inappropriate installations or improper use of the device.
3. Specifications
- Size: 115 x 73 x 32mm. Weight: 120gr (battery included)
- Power source: DC 8-30V
- Operating temperature: from -20°C to 60°C
- Rechargeable backup battery: 1150mA/h i-Ion (3,7Vdc) - more than 4h of
- autonomy in “operating mode”
- Power consumption: in “operating mode” (GPS, GSM, G-Sensor ON and GPRS
- in transmission) <90mA @ DC 12V; in “idle mode” (GPS and GPRS OFF, GSM
- and G-Sensor ON) <30mA @ DC 12V; in “sleep mode” (GPS, GSM and GPRS
- OFF, G-Sensor ON) <18mA @ DC 12V
- GSM/GPRS and GPS/G ONASS Status ED
- Gemalto dual-band GSM/GPRS module
- Communication channels: SMS and GPRS (TCP/UDP)
- GSM and GPRS channels simultaneously
- Hands free and Voice wiretapping (optional)
- Unit programming by Serial, USB, SMS or GPRS
- SIM card PIN code protection
- 5 VIP SMS numbers
- Sophisticated power saving mode setting
- Mileage Counter (by GPS/G ONASS)
- Service function for vehicle maintenance (On-Off)
- Roaming setting (On-Off)
- Real time Tracking and ogging (Time, Distance and/or Heading)
- Daily Timer report (up to 3 pre-defined Timers per day)
- Wake-up on movement and Entering sleep mode reports
- Tow and Speed limit reports (by GPS/G ONASS)
- GPS/G ONASS antenna destroy
- Jamming function
- Driver ID recognition (up to 150 drivers - by optional RFTAG, or up to 3.000
- drivers by optional wired KPAD)
- Analog sensors management (e.g. optional wired Temperature Sensor)
- I/O expansion box management (optional)
- High sensitive MTK GPS/G ONASS dual-mode receiver with built-in antenna
- 4 Inputs: 2 Positives (or Analog) + 2 Negatives/Counters
- 4 digital Outputs (Negatives 200mA)
- “IG” function for “Engine On” & “Engine Off” detection without connecting
- Input 1 to ACC signal
- Journey logging up to 80,000 fixes
- ogical functions: 30 powerful user-defined reports configurable by remote
- Geo-fencing function: 30 geo-fencings controlled by user-defined reports
- Time schedule function: 30 time schedules controlled by user-defined reports
- 3 Serial ports RS-232 communication protocol
- Built-in G-Sensor (adjustable sensitivity by remote)
- Built-in 2,4GHz RF receiver
- Firmware upgrading by remote (FTP)
- Unit password setting (for Control Base Center only)

. Status LED and wiring description
Device status LED:
GSM LED - Red
Status Des ription
ff Phone module switched off or in “sleep mode”
Blinking
600 ms n / 600 ms ff
SIM card no
t inserted
, Pin code
enable (to be
removed) or GSM network authentication in
progress
Blinking
100 ms n / 3 sec ff GSM network successfully authenticated
Blinking
2 x 100 ms n / 2,5 sec ff
GPRS Server successfully connected
GPS LED (Dual-mode GPS/GLONASS re eiver) - Green
Status Des ription
ff
GPS/G
ONASS
receiver
switch
ed
off or in “sleep
mode”
B
linking
1 sec n / 1 sec ff
Invalid GPS/G ONASS fix
n
GPS/G ONASS
position successfully acquired
,
valid fix
Attention please: Before power up the device
it’s necessary to insert the SIM card into the
card reader which is placed on the bottom side
of the device (please remove the black panel in
order to accede the reader).
Attention please: By using a cell phone, please
disable the SIM card Pin code before inserting it
into the device.
5. Quick start
1- After inserting the SIM card, please turn ON the device by connecting Red
1- wire (Positive) and Black wire (Negative) to main power supply. Please
1- connect also White wire (Input 1) to ACC signal (+15) in order to maintain
1- the device On during the testing procedure. When the device is successfully
1- connected to power supply then both red and green LED start blinking.
2- Please wait for few seconds till the phone module successfully authenticate
1- to the GSM network. When the connection is established then red LED
1- starts blinking (2 x 100 ms On / 2,5 sec Off).
3- In order to get the first valid fix, it’s necessary to place the device in an
1- appropriate place (open sky) avoiding any metal surface obstructing it.
1- When GPS/G ONASS is fixed then green LED lights steady (On).
4- By sending an SMS message to the unit it’s possible to pair your mobile
1- phone number (up to 2 numbers) and to assign an ID name to the device
1- (max 12 characters). The SMS string you need to send is:
1- #CFG*Cell.1*Cell.2*Name#
1- Example of string you need to send for enabling one SMS phone number
1- only and for assigning an ID name:
1- #CFG*[phone]**X360#
5- When the device is turned ON and GSM module is ON (red ED is blinking)
1- it’s possible to query the position from your mobile phone by sending XPOS
1- SMS string. Through SMS channel it’s also possible to control a pre-defined
1- output from remote. To enable the predefined output please send XON
1- command string by SMS; to disable it please send XOFF command string.
1- By sending XCALL SMS, it’s possible to receive to your mobile phone a
1- “Silent listening” call from the device (optional external microphone must be
1- connected to the unit), and also a “2 Ways” call by sending XCALL2 SMS
1- string (both optional external microphone and speaker must be connected
1- to the unit).
1- Moreover, it’s possible to manage “Auto-Target” function from 3 predefined
1- sizes of radius: Small, Medium e arge. Based on which radius you want to
1- enable, the command strings to send by SMS are: XGEOSON (Small radius
1- Target enabled), XGEOMON (Medium radius Target enabled) and
1- XGEOLON ( arge radius Target enabled); to disable them please send:
1- XGEOSOFF (Small radius Target disabled), XGEOMOFF (Medium radius
1- Target disabled) and XGEOLOFF ( arge radius Target disabled).
1- Only pre-defined numbers from Control Base Center or by CFG SMS self-
1- setting procedure (please refer to point N.4) are able to manage these
1- functions.
Attention please: for a better management and functionality the device must
be pre-configured and fully tested from the reference Control Base Center.

Serial ports, USB port and Speaker connections:
Serial 1: Dedicated connector for main Serial port interfacing (RS-232
communication protocol). Any external accessory must be connected by female
DB-9 type connector.
USB: This port is dedicated for FW upgrade process (mini-USB cable is not
included into the kit). Please note that this operation is reserved for Control
Base Centers only.
Serial: Combined dedicated connector for Serial ports 2 and 3 interfacing (RS-
232 communication protocol). Any external accessory must be connected by
open wires.
SPK: Connect external speaker (optional).
Serial 1 (Main Serial port - male DB-9 onne tor)
Pin 1:
No
t
u
sed
Pin 2:
Data r
eception (RX)
Pin 3:
Data transmission (TX)
Pin 4:
Positive (DC 5V / 500m
A
)
Pin
5
:
Negativ
e
(GND)
Pin 6:
No
t
u
sed
Pin 7:
No
t
u
sed
Pin 8:
No
t
u
sed
Serial (Serial ports 2 and 3 – mi ro fit onne tor) Wire
Pin 1:
Negativ
e
(GND)
–
Serial No.2
Black
Pin 2:
Positive (DC 5V / 500mA)
–
Serial No.2
Red/Black
Pin 3:
Data transmi
ssion (T
X
)
–
Serial No.
2
Grey/Black
Pin 4:
Data r
eception (RX)
–
Serial No.
2
White
/Black
Pin 5:
Negativ
e
(GND)
–
Serial No.3
Black
Pin 6:
Positive (DC 5V / 500mA)
–
Serial No.2
Green
/Black
Pin 7:
Data transmission (TX)
–
Serial No.3
range
/Black
Pin 8
:
Data r
e
ception (RX)
–
Serial No.3
Yellow/Black
Power/Inputs/Outputs, Microphone and Antennas connections:
P/I/O: Combined dedicated connector for Power, Inputs and Outputs
connections. The unit allows to manage up to 4 Inputs (2 Positives + 2
Negatives/Counters) and up to 4 digital Outputs (all Negatives).
(*) “IG” Fun tion: Connecting Red & Black wires from AV unit to Positive &
Negative signals of vehicle main battery, it’s possible to detect “Engine On” &
“Engine Off” status without connecting Input 1 to Ignition Key signal. Enabling
this function, the Input 1 wire becomes available for other use.
In order to let this function enable please take contact with the C.B.S.
providing them the exactly voltage levels measured on the main battery circuit
on both “Engine On” & “Engine Off” conditions.
P/I/O (Power, Inputs and Outputs) Wire
Pin 1: Power ‘+’ (Positive
DC
8
-
3
0V
)
(*)
R
ed
Pin 2:
Power
‘
–
‘ (Negativ
e
GND)
(*)
Black
Pin 3:
Input 1 Positive (>DC 6V)
-
Ignition Key
(*)
or Analog Input 1 (DC 0-30V) White
Pin 4:
Input 2 Positive (>DC 6V)
or Analog Input 1 (DC 0-30V) Grey
Pin
5: Input 3 Negative
/Counter
(<DC 0,8V)
Green
Pin 6: Input
4
Negative
/Counter
(<DC 0,8V)
Violet
Pin 7: Output 1 Negative (
16
0mA @ DC 12V)
Yellow
Pin 8: Outp
ut
2
Neg
a
tive (
16
0mA @ DC 12V)
range
Pin 9: Output
3
Negative (
16
0mA @ DC 12V)
Brown
Pin 10: O
utput
4
Negative (
16
0mA @ DC 12V)
Blu
e
MIC: Connect external microphone (optional).
GSM: Connect the GSM antenna, included into the kit.
GPS: Connect the external GPS/G ONASS antenna, included into the kit.
Attention please: In order to get the first valid GPS, fix it’s necessary to
move the vehicle in open sky environment and to install the unit in an
appropriate place without any metal surface obstructing the GPS/G ONASS
antenna.
When the GPS ED (green ED) becomes still ON then the fix is considered
valid and the first position is acquired.
This operation might take few minutes.
Serial 1
USB
Serial
SPK
GSM GPS
MIC
P/I/O

Installation diagram for X-360 tracker
In
put
1
(White)
Positive
(>
DC
6
V
)
Ignition Key
(*)
or Analog 1 (DC 0-30V)
In
put
2
(Grey)
Posit
ive
(>
DC
6
V
)
or Analog 2 (DC 0-30V)
Input 3
(Green)
Negativ
e
(
<DC
0,8V)
In
put 4
(Violet)
Negativ
e
(
<DC
0,8V)
Outputs Inputs
Power supply
(*) “IG” Function: Connecting Red & Black wires from AVL unit to
Positive & Negative signals of vehicle main battery, it’s possible to
detect “Engine n” & “Engine ff” status without connecting Input 1
to Ignition Key signal. Enabling this function, the Input 1 wire
becomes available for other use.
In order to let this function enable please take contact with the
C.B.S. providing them the exactly voltage levels measured on the
main battery circuit on both “Engine n” & “Engine ff” conditions.
Power supply +
(Red)
Positive (+)
(*)
DC 8-30V
Power supply
–
(Black)
Negative (
–
)
(*)
GND
“IG”
Fun tion
Output 1
(Yellow)
Negative (
16
0mA @
DC
12V
)
Outpu
t
2
( range)
Negative (
16
0mA @
DC
12V
)
Output 3
(Brown)
Negative (
16
0mA @
DC
12V
)
Out
put 4
(Blue)
Negative (
16
0mA @
DC
12V
)
GSM antenna
GPS
GSM
X
-
3
60
GPS/GLONASS
antenna
P/I/O