XENO XBC28V12DN1M3IR User manual

Norbain SD Ltd
210 Wharfedale Road
IQ Winnersh
Wokingham
UK
RG41 5TS
0118 912 5000
1.3MP Analogue bullet camera
Installation and user guide
Please read this document before installing or
powering the camera
Do not attempt to disassemble the camera; it
does not contain any serviceable parts
XBC28V12DN1M3IR
XBC28V12SDN700IR Manual version 1.0
The crossed-out wheeled bin mark
symbolizes that within the European Union
the product must be collected separately at
the product end-of-life. This applies to your
product and any peripherals marked with
this symbol. Do not dispose of these
products as unsorted municipal waste.
This apparatus is manufactured to comply
with the radio interference. A Declaration
of Conformity in accordance with the
following EU standards has been made.
The manufacturer declares that the
product supplied with this document is
compliant the provisions of the EMC
Directive 2004/108/ EC, the CE Marking
Directive 93/68 EEC and all associated
amendments.CE RoHS2 2011/65/EU

Installation:
1. Use the camera bracket as a template to mark
the fixing hole locations.
2. Drill a 22mm hole in wall to allow cable and OSD
joystick to pass through.
3. Pass the cable through the wall and connect the
video and power cables
Camera power 12VDC +/- 10%
Polarity conscious, centre pin positive
4. Drill the fixing holes, and using suitable fixings for
the wall material, secure the camera to the wall.
5. Loosen the 2 adjusting screws on the camera
bracket to allow it to be correctly orientated, then
tighten the screw (Do not try to force the camera
position when screws are tight)
6. Use the supplied Allen key to adjust the zoom
and focus pots on the base of the camera, to
achieve the required picture.
7. If necessary, adjust the camera settings using
OSD joystick control on the camera cable.
8. Press the central button to enter the menu set up
page.
9. Navigate the menus and change settings using
the Left / Right / Up and Down directions.
10. Always ensure that settings are saved before
exiting the menus.
Trouble shooting
1. No picture after powering up:
Incorrect voltage
Wrong polarity
Badly made BNC connector
2. Horizontal lines travelling up the screen:
Generally cased by an AC hum, requires a
hum rejection unit
WARNING
This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
Specification
Model
XBC28V12DN1M3IR
Sensor
1/3" SONY 1.3Megapixel
CMOS Sensor
Effective Pixels
1305(H) X1049(V) (1.3MP)
Resolution
1000TVL
Minimum
Illumination
0.01 Lux / F1.2 & 0 Lux IR on.
Video output
0.8 V –1.2 Vpp
Lens
1/2.7” 2.8-12mm 2 mega pixel
f1:1.4
IR LEDs
42 LEDs up to 40M
S/N Ratio
More than 52dB
Scanning
System
2:1 interlaced
Synchronous
System
Internal, Negative sync.
Electronic
Shutter
1/50s~1/100,000s
Gama
0.45
Video Output
1Vpp, 75Ω
AGC
Auto
Power
DC12V(+/-10%)/500mA
WDR
D-WDR - OFF - ON - (LEVEL:
0-63)
BLC
Yes –selectable areas
HLC
LEVEL (0-255 ) / MODE (ALL
DAY / NIGHT ONLY)
White balance
AWB-pro, AWB-tempora, AWB-
ai, AWB-gw, AWB-cct,
Image
Mirror, Flip, Brightness range
0-250 , Zoom in 5x -
3DNR
On/Off
Motion
detection
4 zones 8 colours
Privacy masks
8 zone 8 colours
Dimension
(mm)
200(W)x171(H)x83(D)
Weight
Net/Gross(g)
1400 /1900
Operating Temp
-10~+500C RH95% MAX
Storage temp
-30~+600C
IP rating
IP65
Approvals
CE RoHS2: 2011/65/EU