Xentino HSP500 User manual

HSP500 Wireless HotSpot Gateway with Printer
0
HSP500
User Manual
Wireless HotSpot Gateway with Printer

HSP500 Wireless HotSpot Gateway with Printer
1
Copyright Notice
Copyright © 2013-2022 Xentino Technologies Inc. All rights reserved. No part of this
document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission.
Disclaimer
We shall not be liable for technical or editorial errors or omissions contained herein;
nor for incidental or consequential damages resulting from furnishing this material,
or the performance or use of this product. We reserve the right to change the
product specification without notice. Information in this document may change
without notice.
Trademarks
Microsoft Win98, Windows 2000, WinXP, Win Vista and Win7 are registered
trademarks of Microsoft Corporation.
General: All other brand and product names mentioned herein may be registered
trademarks of their respective owners. Customers should ensure that their use of
this product does not infringe upon any patent rights. Trademarks mentioned in this
publication are used for identification purposes only and are properties of their
respective companies.

HSP500 Wireless HotSpot Gateway with Printer
2
Contents
1Introduction ...........................................................................................................4
1-1 Package Contents...................................................................................5
1-2 Features .................................................................................................5
1-3 Precautions ............................................................................................6
1-4 Outlook ..................................................................................................6
1-4-1 Printing a test page...........................................................................0
1-4-2 How to load paper rolls ....................................................................0
1-5 Technical Specifications .........................................................................1
1-5-1 Hardware Specifications...................................................................1
1-5-2 Software Specifications ....................................................................2
2Installation .............................................................................................................0
2-1 Connecting the Antennas ......................................................................0
2-2 Installation Requirements......................................................................0
2-3 Getting Start...........................................................................................0
3Configuring the HSP500 .........................................................................................1
3-1 Setting Wizard........................................................................................1
3-2 Advanced Setup .....................................................................................8
3-2-1 Authentication..................................................................................9
3-2-1-1 Authentication........................................................................9
3-2-1-2 RADIUS..................................................................................11
3-2-2 Billing ..............................................................................................13
3-2-2-1 Billing....................................................................................13
3-2-2-2 Accounting............................................................................16

HSP500 Wireless HotSpot Gateway with Printer
3
3-2-2-3 Credit Card............................................................................21
3-2-3 Management ..................................................................................25
3-2-3-1 Syslog ....................................................................................25
3-2-3-2 Session Trace........................................................................33
3-2-3-3 Bandwidth ............................................................................35
3-2-3-4 SNMP.....................................................................................36
3-2-4 Security ...........................................................................................37
3-2-4-1 Pass Through........................................................................37
3-2-4-2 Filtering ................................................................................39
3-2-4-3 Secure Remote .....................................................................41
3-2-5 System ............................................................................................42
3-2-5-1 System...................................................................................42
3-2-5-2 WAN/LAN.............................................................................45
3-2-5-3 Server....................................................................................47
3-2-5-4 Customization ......................................................................50
3-2-5-5 Portal Page............................................................................59
3-2-5-6 Advertisement......................................................................60
3-2-5-7 Walled Garden......................................................................61
3-2-5-8 DDNS .....................................................................................62
3-2-5-9 Wireless ................................................................................64
3-2-5-10 USB......................................................................................67
Appendix A Signal Connection Arrangements.............................................................68
Appendix B Regulations/EMI Compliance ...................................................................69
LIMITED WARRANTY ....................................................................................................70

HSP500 Wireless HotSpot Gateway with Printer
4
1Introduction
The HSP500 is a compact intelligent gateway. It provides Plug’ Play Internet access,
advanced security and network management.
The HSP500 is designed for service providers, system integrator or hotspot venue
operator without backend-RADIUS-Server to have integrated solution for rapid
deployment, which can start hotspot service quickly and easily and enhance service
performance.
The HSP500 is an ideal solution for hotel lobbies, coffee bars, airport lounges,
conference facilities and other sites that commonly host business travelers, and
offers instant high-speed Internet connections. With its IP Plug and Play technology,
it accepts any client configuration login, when client open browser the HSP500
immediately recognizes new end-user and redirects their browser to customized
Web pages. There’s no need for end-user to change any of their default network
(Static IP), e-mail (SMTP Server behind firewall), or browser settings (HTTP Proxy) or
load any special software to access hotspot service. It’s completely Plug’ Play with
any browser.
The HSP500 provides QR code service. You can install any QR code APP to your
mobile device, and then scan QR code on the ticket to get access of the Internet! You
could save the time to key in the account and the password.

HSP500 Wireless HotSpot Gateway with Printer
5
1-1 Package Contents
Please inspect your package. The following items should be included:
HSP500
One HSP500
One Thermal papers (50 meter)
One Power Adapter
One Ethernet Cable (1.5 meter)
One Quick Installation Guide
Two Detachable Antennas
One Product CD
One Wi-Fi Label
If any of the above items are damaged or missing, please contact your dealer
immediately.
1-2 Features
Wireless data rates up to 300 Mbps
Supports up to 30 simultaneous Users
IP Plug and Play (iPnP)
Comprehensive security
64/128-bit WEP encryption
WPA encryption
WPA2 Encryption
IP/URL filtering
Intelligent Management
Built-in AAA (Authentication/Accounting/Authorization) and Billing
mechanism
Internet access via QR code scanning
Note: The "iPnP" Function only can be used with TCP/IP-based Network.

HSP500 Wireless HotSpot Gateway with Printer
6
1-3 Precautions
Never remove or open the cover. You may suffer serious injury if you touch
these parts.
Never install the system in the wet locations.
Use only the original fitting AC power adapter otherwise there is a danger of
severe electrical shock.
Avoid exposing the HSP500 to direct sunlight or another heat source.
Choose a well-ventilated area to position your HSP500.
1-4 Outlook
Figure 1-4-2 Rear Panel
Figure 1-4-1 Front Panel

HSP500 Wireless HotSpot Gateway with Printer
7
1. Paper roll housing
2. Printer Cover
3. Tear Bar, for paper cutting
4. Button A
5. Button B
6. Button C
7. Push Button, for printer cover opening
8. Reset Button
9. DC power supply connector
10. RJ45 port
11. Micro USB connector
12. WLAN LED (Green)
13. UPLINK LED(Yellow)
14. SMA connector
15. SMA connector
WLAN LED:
Off: The wireless is not ready.
Green light: The HSP500 has established a valid wireless connection.
Green Blinking: The wireless connection is active.
UPLINK LED:
Off: A port has not established any network connection.
Yellow light: A port has established a valid 10/100 Mbps network
connection.
Yellow Blinking: 10/100 Mbps traffic is traversing the port.
Reset Button: The HSP500 has a reset button at the rear panel of the
device. Use this function to reset the system back to factory defaults.
Power Jack: Used to connect the external power supply with the HSP500.

HSP500 Wireless HotSpot Gateway with Printer
0
1-4-1 Printing a test page
After you have installed your printer, you should print a test page to make sure the
printer is functioning properly. To do this act as follows:
1. Turn the printer off.
2. Hold down the button A for approximately five seconds, and then turn the
printer on.
3. The printer will print a test page.
1-4-2 How to load paper rolls
Please follow the steps to correctly load paper rolls.
1
2
3
Figure 1-4-3 Paper rolls loading
4

HSP500 Wireless HotSpot Gateway with Printer
1
1-5 Technical Specifications
1-5-1 Hardware Specifications
Network Specification
IEEE802.3 10BaseT Ethernet
IEEE802.3u 100BaseTX Fast Ethernet
IEEE802.11b/g/n Wireless LAN
ANSI/IEEE 802.3 NWay auto-negotiation
Wi-Fi Compatible
Connectors
One WAN Port (10BaseT/100BaseTX Auto cross-over)
One Micro USB connector
Encryption
WEP (Wired Equivalent Privacy) 64/128-bit RC4
WPA (Wi-Fi Protected Access)
WPA2 (Wi-Fi Protected Access)
External Antenna Type
Dual detachable diversity antenna with reverse SMA
LED Indicators
One POWER LED
One WAN 10/100M Link/Activity LED
One Wireless Link/Activity LED
One System LED
Power Requirement
External Power Adapter
Input: 100-240 VAC, 50/60 Hz
Output: 12V, 1.5A
Environment Conditions
Operating Temperature: 0 to 50°C
Storage Temperature: -10 to 60°C

HSP500 Wireless HotSpot Gateway with Printer
2
Operating Humidity: 20~80% non-condensing
Storage Humidity: 20% to 90% non-condensing
Certifications
FCC part 15 Class B, CE , C-Tick , VCCI
Dimension
Size: 109×155×90 (W×D×H )mm
Weight: About 340g (Net)
Printer Tray
Push button: push to open printer cover
Tear bar: cuts receipt paper
Button A: flashing when printer cover is opened
Paper roll housing: put paper roll here
Paper Roll and Printing
Paper width: 58 (+0/-1)mm
Paper length: 50M (max.)
Paper thickness: 65 um
Paper roll outside diameter: 63 (+2/-2) mm
Paper roll inside diameter: 12 (+0.5/-0) mm
Paper Detection: Photo interrupter
Printing width: 48 mm
Printing Method: Direct thermal
Printing Speed: 25.4 mm/ sec
Dot resolution (dots/ mm): 8 (203 dpi)
Thermal head service life: 1 pulses or 50Km
1-5-2 Software Specifications
Networking
IEEE802.3 10BaseT Ethernet
IEEE802.3u 100BaseTX Fast Ethernet
IEEE802.11b Wireless LAN
IEEE802.11g Wireless LAN
IEEE802.11n Wireless LAN
Supports 30 Simultaneous Users
IP Plug and Play (iPnP)

HSP500 Wireless HotSpot Gateway with Printer
3
HTTP Proxy Support
WEP64/128bit
WPA-PSK (TKIP)
WPA2-PSK(AES)
WPA/WPA2 Mix mode
SMTP Server Redirection
DHCP Server(RFC 2131)
DHCP Relay(RFC 1542)
Static IP WAN Client
DHCP WAN Client
PPPoE WAN Client(RFC 2516)
PPTP WAN Client
NAT(RFC 1631)
IP Routing
NTP (Network Time Protocol) Support
Local Account: 256
Max Session Number: up to 16384
Marketing Cooperation
Advertisement URL link
Walled garden
Customizable log-on and log-off pages
Portal Page
User Accounting and Authentication
Built-in Authentication
Web-based Authentication
RADIUS AAA Support (RFC 2865, 2866)
Secondary RADIUS
User Authentication and Accounting
Logout Window Timer Control
Security and Firewall
Layer 2 Isolation Security
SSL User Login page/ Configuration Page
SSL Administration
VPN Pass through (IPSec/PPTP)
Customize SSL Certificate

HSP500 Wireless HotSpot Gateway with Printer
4
Pass Through IP/MAC/URL Address
Restricted Destination Filtering IP/URL
VPN (IPSec/PPTP) Pass through
PPTP VPN Client
WEP
WPA
WPA2
WPA/WPA2 Mix mode
Management
Web-based Management Tool
Firmware Upgrade via HTTP/TFTP
Wizard setup for step-by-step Configuration
Backup/Restore/Factory Default Setting
Remote Authorized Management
Real-time Session List
Syslog (System/Subscriber/LAN device)
E-mail logs
SNMP v1/v2 (MIB II, Private MIB)
System Information Table
Status Report (Daily/Monthly/System/Network)
SSL certificate upload

HSP500 Wireless HotSpot Gateway with Printer
0
2Installation
2-1 Connecting the Antennas
The HSP500 provides two antenna connectors on the rear of the unit.
2-2 Installation Requirements
Before installing the HSP500, make sure your network meets the following
requirements.
System Requirements
The HSP500 requires one of the following types of software:
Windows 98 Second Edition/NT/2000/XP/Vista
Red Hat Linux 7.3 or later version
MAC OS X 10.2.4 or later version
Any TCP/IP-enabled systems like Mac OS and UNIX (TCP/IP protocol
installed)
Standard phone line for xDSL modem Or Coaxial cable for Cable modem
Web Browser Software (Microsoft I.E 5.0 or later version or Netscape
Navigator 5.0 or later version)
One computer with an installed 10Mbps, 100Mbps or 10/100Mbps Ethernet
card
UTP network Cable with a RJ-45 connection (Package contents)
Note: Prepare twisted-pair cables with RJ-45 plugs. Use Cat.5 cable for all
connections. Make sure each cable not exceed 328 feet (Approximately 100 meters).
ISP Requirements
Verify whether your ISP use fixed or dynamic IP. If it is a fixed IP, be sure to get the IP
from your ISP. For dynamic IP, which is mostly used, the PC will get the IP
automatically whenever it hooks up on the modem.

HSP500 Wireless HotSpot Gateway with Printer
1
Dynamic IP
Dynamic IP Setting
Fixed IP
Your fixed IP address for the HSP500
Your subnet mask for the HSP500
Your default gateway IP address
Your DNS IP address
PPPoE
Your user name and password from your ISP
PPTP
PPTP Server IP Address from your ISP
PPTP Local IP address from your ISP.
PPTP Local IP subnet mask from your ISP.
Your user name from your ISP
Your password from your ISP
Your PC Requirements
The Static IP settings for the PC
Your PC’s fixed IP address
Your PC’s subnet mask
Your PC’s default gateway IP address
Your PC’s primary DNS IP address
Note:
1. The gateway’s default IP address setting is “10.59.1.1”.
2. The gateway’s default subnet mask setting is “255.255.255.0”.
The Dynamic IP settings for the PC
We recommend that you leave your IP settings as automatically assigned. By default,
the HSP500 is a DHCP server, and it will give your PC the necessary IP settings.

HSP500 Wireless HotSpot Gateway with Printer
0
2-3 Getting Start
HSP500 Connection
1. Connect the DC power adapter to the HSP500 and plug it into a power socket.
2. Connect HSP500 and xDSL modem with an Ethernet Cable.

HSP500 Wireless HotSpot Gateway with Printer
0
Configure TCP/IP of your computer
For Windows user,
1. Click Start > Control Panel, click Switch to Classic View and double click on
Network Connections.
2. Right click on the Local Area Connection and click Properties.
3. Double click Internet Protocol (TCP/IP).
4. Choose Obtain an IP address automatically.
5. Click OK to close the Internet Protocol (TCP/IP) Properties and click OK again to
close the Local Area Connection.
Figure 2-3-1 TCP/IP Setting

HSP500 Wireless HotSpot Gateway with Printer
1
3Configuring the HSP500
3-1 Setting Wizard
Step 1: The ESSID’s name by default is related to the last 4 numbers of WLAN MAC. If
the WLAN MAC is “00-90-0E-00-12-34”, the default is “Xentino-1234_1”.
Please search ESSID “Xentino -1234_1”and connect it.
Step 2: Start your browser, and then enter the factory default IP address 10.59.1.1 in
your browser’s location box. Press Enter.
Figure 3-1-1 Web Browser Location Field (Factory Default)
Step 3: The HSP500 configuration tools menu will appear. In the Username and
Password field, type the factory default user name admin and password admin and
click Login. If you are first time setting the system, the wizard setup screen will
appear. You will be guided, step-by-step, through a basic setup procedure.
Step 4: Internet Connection Setting
Select the appropriate Internet connection type to connect to your ISP.
Figure 3-1-2 Internet Connection Setting Screen

HSP500 Wireless HotSpot Gateway with Printer
2
DHCP Client
The device can work as a DHCP client. This allows the device to obtain the IP address
and other TCP/IP settings from your ISP. If your xDSL/Cable comes with this feature,
please enable Use DHCP Client.
Figure 3-1-3 Internet Connection Setting Screen

HSP500 Wireless HotSpot Gateway with Printer
0
Static IP Setting
If Static IP Setting is selected, then this screen will appear. Enter the IP address
information provided by your ISP.
Figure 3-1-4 Internet Connection Setting Screen—Static IP Setting
Item
Default
Description
IP Address
0.0.0.0
Enter the IP address provided by your ISP.
Subnet Mask
0.0.0.0
Enter the subnet mask for the IP address.
Gateway IP Address
0.0.0.0
Enter the Gateway IP Address provided by your ISP.
Primary DNS Server
Empty
Enter the primary DNS server IP address for the xDSL/Cable connection
(provided by your ISP).
Secondary DNS Server
Empty
Enter the secondary DNS server IP address for the xDSL/Cable connection
(provided by your ISP). If the primary DNS Server IP were not available,
meanwhile, Secondary DNS Server IP would start in the same time.