Xerox XL-795D User manual

1
XL795D
Service Manual

2
TABLE OF CONTENTS
SERVICE WARNING·················································3
A. IMPORTANT SAFETY INSTRUCTION·····················3
B. SPECIFICATIONS·········································4
C. TIMING CHART······································5
D. CONTROL LOCATION·································7
E. CONDUCTION VIEW········································8
F. ADJUSTMENT PROCEDURE·······························11
G. TROUBLE SHOOTING HINTS···························12
H. REPLACEMENT PARTS LIST···························16
I. BLOCK DIAGRAM······································28
J. SCHEMATIC DIAGRAM································29

3
WARNING
To prevent from fire or shock hazard,do not expose monitor to any rain or any form of water.High voltage is
inside the monitor so please do not remove the back cover of the cabinet if you are not a qualified monitor
engineer.Contact the local dealer or the nearest Xerox branch office if you need help.
A. IMPORTANT SAFETY INSTRUCTION
Prior to using this service manual,please ensure that you have carefully followed all the procedures outlined in the
user's manual for this product.
1. Read all of these instructions.
2. Save these instructions.
3. Follow all warnings and instructions a marked on the product.
4. Unplug this product from the wall outlet before cleaning.Do not use liquid cleaners or aerosol
cleaners, use a damp cloth for cleaning.
5. Do not use this product near water.
6. Do not place this product on an unstable cart,stand or tablle.The product may fall,causing serious
damage to the product.
7. Slots and openings in the cabinet and the back or bottom are provided for ventilation,to ensure
reliable operation of the product and to protect it from overheating,those openings must not be
blocked or covered.The openings should never be blocked by placing the product on a bed,sofa, rug,
or other similar surface.This product should not be placed in a built-in installation less proper
ventilation is provided.
8. This products should be operated from the type of power source indicated on the marketin label.
If you are not sure of the type of power available, consult your dealer or local power company
9. This product is equipped with a 3-wire grounding type plug,a plug having a third (grounding)
pin.This plug will only fit into a grounding-type power outlet.This is a safety feature,if you are
unable to insert the plug into the outlet,contact your electrician to replace your obsolete outlet.Do
not defeat the purpose of the grounding-type plug.
10. Do not allow anything to rest on the power cord.Do not locate this product where persons will walk
on the cord.
11. If an extension cord is used with this product,make sure that the total of the ampere ratings on the
product plugged into the extension cord to the waplugged into outlet does not exceed 15 ampere.
12. Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electric shock.Never spill liquid
of any kind on the product.
13. Do not attempt to service this product yourself,as opening or removing covers may expose you to
dangerous voltage points or other risks.Refer all servicing to service personnel.
14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions.
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally,when the operating instructions are followed.Adjust
only those controls that are covered by the operating instructions since improper adjustment of
other controls may result in damage and will often require extension work by a qualified
technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance,indicating a need for service.

4
B. SPECIFICATIONS
1. Maximum Resolution 1280 x 1024 @ 75Hz
2.Recommend Resolution 1280 x 1024 @ 60Hz
3. Synchronization Range
Horizontal
Vertical
31 –80 KHz
60– 75 Hz
4. Active Display Area 376mm (H) x 301mm (V)
5. Dot Pitch 0.294(H) x 0.294(V) mm
6. Support display colors 16.7Mcolor
7.Contrast Ratio (Typical) 600
8.Luminance of White 250cd/m²
9.Bandwidth 135MHz
10.User Control 4 Key Switch
11.OSD Function Brightness, Conrast, H-Pos, V-Pos, H. Size, Phase, Color Select,
Auto, Reset, Language, OSD Adjust, Exit
12.View Angle CR=5
Horizontal
Vertical
85 , 85 Degrees
85 , 85 Degrees
13. Power Source 100 –240 Vac 60 / 50 Hz
14. Power Consumption 60W(max.)
15. Connection Type 15 Pin D Type / DVI
16. Input Signal
Video
Sync.
Analog R.G.B. , 0.7Vp-p / 75 Ohms
TTL level,positive or negative polarity
17.Color Temperature Cool / Natural / Warm
18.Dimension (WxHxD) Packing
Set 484mm x 500mm x 150mm 420mm x 428mm x 170mm
19. Monitor Weight 7.3Kg / 6.1Kg
20.Base Operation
Tilt 0 / + 15 degree
21.Power Saving
ON
STAND BY
OFF
＜60W
＜5W
＜5W
22.Signal Connector Pin Assignment
Pin No.
1. Red 9. VDD from PC for DDC
2. Green 10. Sync. Ground
3. Blue 11. Ground
4. Ground 12. SDA (For DDC)
5. Self Test 13. Horizontal Sync.
6. Red Ground 14. Vertical Sync.
7. Green Ground 15. SCL (For DDC)
8. Blue Ground
23.Audio signal 3.5F stereo phone jack
2.5+2.5W 8O Speaker

5
C.TIMING CHART
Video
Back porch Active display Front porch
Sync.
Sync-width
Total
Preset
Modes
VGA
720X400
VGA
640X480
VESA
640X480
VESA
640X480
VESA
800X600
VESA
800X600
VESA
800X600
Pixel clock
(MHz) 28.325 25.175 31.500 31.500 36.000 40.000 50.000
H-Frequency (KHz)
31.472 31.469 37.861 37.500 35.156 37.879 48.077
H-Total (µ
s)
31.774 31.778 26.413 26.667 28.444 26.400 20.800
H-Active Display
(µs)
25.419 25.422 20.317 20.317 22.222 20.000 16.000
H-Blanking
(µs) 6.355 6.356 6.095 6.349 6.222 6.400 4.800
Front Porch
(µs) 0.635 0.636 0.762 0.508 0.667 1.0001.120
H-Sync-width (µs)
3.813 3.813 1.270 2.032 2.000 3.200 2.400
H-Back Porch
(µs) 1.906 1.907 4.063 3.810 3.556 2.200 1.280
V-Frequency
(Hz) 70.1 59.94 72.81 75.0 56.25 60.3 72.2
V-Total
(ms) 14.267 16.683 13.735 13.333 17.778 16.579 13.853
V-Active Display
(ms) 12.710 15.253 12.678 12.800 17.067 15.840 12.480
V-Blanking
(ms) 1.557 1.430 1.057 0.533 0.711 0.739 1.373
V-Front Porch (ms)
0.413 0.318 0.238 0.027 0.028 0.026 0.770
V-Sync-width (ms)
0.064 0.064 0.079 0.080 0.057 0.106 0.125
V-Back Porch (ms)
1.080 1.049 0.740 0.427 0.626 0.607 0.478
H/V Sync. Polarity －＋－－－－－－＋＋＋＋＋＋
Interlace NONE NONE NONE NONE NONE NONE NONE

6
Preset
Modes
VESA
800X600
VESA
1024X768
VESA
1024X768
VESA
1024X768
VESA
1280X1024
VESA
1280X1024
Pixel clock
(MHz) 49.50065.000 75.000 78.750 108.00 135.00
H-Frequency (KHz)
46.875 48.363 56.476 60.023 63.981 79.976
H-
Total (µs)
21.333 20.677 17.707 16.660 15.630 12.540
H-Active Display (µs)
16.162 15.754 13.563 13.003 11.852 9.481
H-Blanking
(µs) 5.172 4.923 4.053 3.657 3.778 3.022
Front Porch
(µs) 0.323 0.369 0.320 0.203 0.444 0.119
H-Sync-width (µs)
1.616 2.092 1.813 1.219 1.037 1.067
H-Back Porch (µs)
3.232 2.462 1.920 2.235 2.296 1.837
V-Frequency (Hz)
75.0 60.0 70.1 75.0 60.0 75.0
V-Total (ms)
13.333 16.666 14.272 13.328 16.661 13.329
V-Active Display (ms)
12.800 15.880 13.599 12.795 16.005 12.804
V-Blanking (ms)
0.533 0.786 0.673 0.533 0.656 0.525
V-Front Porch (ms)
0.021 0.062 0.053 0.017 0.016 0.013
V-Sync-width (ms)
0.064 0.124 0.106 0.050 0.047 0.038
V-Back Porch (ms)
0.448 0.600 0.513 0.466 0.594 0.475
H/V Sync. Polarity ＋＋－－－－＋＋＋＋＋＋
Interlace NONE NONE NONE NONE NONE NONE

7
D. CONTROL LOCATION
Font control panel
1. Menu button (MENU) 4. Auto button (AUTO)
2. Select button (DOWN) 5. Power button (POWER)
3. Select button (UP) 6. Power Indicator
Rear panel
The rear panel of the monitor includes 3plug-in connectors. They are as follows:
1. One DC IN connector
2. Two VGA Signal (DVI / D-sub) IN connectors

8
E. CONDUCTION VIEW
MAIN BOARD (Component Side)

9
MAIN BOARD (Component Side)

11
F. ADJUSTMENT PROCEDURE
ITEM
Program Menu.
﹟Test Meter
﹡Test Point
﹫Pattern Operation
Check
Value
A
B+
Check
﹟Digital Voltmeter
﹡CN7
﹫Crosshatch Pattern
(31.5KHz,640x480)
1. Plug power cable into the adapter, check adapter
power indicator light up green.
2. Make sure the voltage of the power plug (CN7)
on the main PCB to the value shown at right.
12.0V
±0.2V
B
Power Saving
Check
﹟Wattmeter
﹟PC or Pattern
generator
﹫Crosshatch Pattern
(31.5KHz,640x480)
1. Unplug the signal cable into the monitor.
2. Turn the power switch of the monitor ON.
3. Check monitor power indicator light up orange.
4. Make sure the wattmeter value shown at right.
5. OSD will be display “NO SIGNAL” Picture.
<2.5W
C
Into Factory
mode
﹟PC or Pattern
generator
﹫Crosshatch Pattern
(31.5KHz,640x480)
1. Hold ‹key,then turn the power switch of the
monitor OFF.
2. Hold ›key,then turn the power switch of the
monitor ON.
3. You can into factory adjustment mode.
D
Auto mode
Check
﹟PC or Pattern
generator
﹫Crosshatch Pattern
(1024x768/60Hz)
1. Press and relese the MENU knob to activate the
OSD menu.
2. Move the OSD to the AUTO function,press MENU
key auto adjuat display mode to its utmost
performance according to VGA setting.
3. In the event of the display image needs further
adjustment
E
White
Balance
Adjust
﹟PC or Pattern
generator
﹫White Pattern
(1024x768/60Hz)
1. Move the OSD to the COLOR mode (AUTO COLOR).
2. set color is 9300°Kusing the OSD,Check the value
shown at right.
Y= 220±0.1FL x= 0.283±0.01 y= 0.297±0.01
3. set color is 7500°Kusing the OSD,Check the value
shown at right.
Y= 220±0.1FL x= 0.299±0.01 y= 0.315±0.01
4. set color is 6500°Kusing the OSD,Check the value
shown at right.
Y= 220±0.1FL x= 0.313±0.01 y= 0.329±0.01
F
OSD
Language
Setting
﹟PC or Pattern
generator
1. Move the OSD to the LANGUAGE mode.
2. You can choose one of the eight language you need.

12
G. TROUBLE SHOOTING HINTS
NO NO
YES YES
YES YES
NO NO
High Voltage !
NO
YES
YES
NO NO
YES
No Display
( Black )
LED ON ?
Push the power
ON/OFF switch
LED Color
change ?
Check main board
Scaler IC
Hi / Lo under
push power sw?
Back light
ON? To Step 2
Make sure the
connection of
Inverter is fine
+12V ?
Check
the Inverter
Check
Fuse of inverter
B
Display ?
OK !
A
To Step 2
Power
adapter ? Change
adapter

13
NO
YES
YES
NO
YES
NO
B
Hi / Lo under
push power sw?
Change the
Inverter
Display ? OK !
To Step 2
A
Check the
connection of
control board
Display ?
OK !
Change the
main board
Change the
main board

14
NO
YES
NO
YES
YES
YES
YES
NO
NO
YES
Step 2
Check the main
board 12V ?
+5.0 V ? Repair
5V Circuit
H/V input
Signal ?
Check the main
board DPMS
Circuit ?
Change
Scaler IC
Check
H/V Signal
Display ?
OK !
Change
Signal Cable
Check
Fuse, Adapter
Repair
DPMS Circuit

15
NO
YES
NO
YES
NO
YES
YES
NO
NO
YES
No display
(White)
Check the main
board 5V ?
+3.3V ?
H/V Input
Signal ?
Check the main
board 3.3V
Regulator
?
Change
Scaler IC
Check
H/V Signal
Display ?
OK !
Change
Signal Cable
Repair
5V Circuit
Check
3.3V
Regulator
Repair
3.3V Circuit

16
H. REPLACEMENT PARTS LIST
NO
Parts No. Description Part Location Q’ty
1988-A05-1000 GA980DL XEROX SET
Color : 877C+K2440
1
2154-500-976D-A19" 976D protection cover For bezel 1
3160-52L-980DL GA-980DL PolyfoamL 1
4160-52R-980DL GA-980DL PolyfoamR 1
5170-001-LCD5-1LCD15" PE Bag 1
6170-005-VM541 LT-541 PE BAG 夾鏈袋
300*200mm.
1
7170-500-AS776 BASE BAG 360*360mm 0.03t 1
8170-500-PS776D PS776D DC LINE BAG 200*340 1
9600-151-1500 Power cable 1.8M
1
10 600-151-15R22 D-Sub 15Pin Signal cable
1
11 846-120-E0AL-SA Adapter LSE 60W DC12V,5A 1
12 003-H01-AS576 TCO99 Label
1
13 002-001-TCO9 TCO99 Declaration
1
14 610-151-19R2A5 DVI-D Signal cable 1.5M
1
15 003-000-ALL-1Bar Code Label 110X50MM 1
16 002-002-0DOC-AFCC DOC Declaration PROVIEW 1
17 002-G50-980DL XEROX Warranty card 1
18 005-500-980DL GA980DL XEROX Carton 1
19 002-U50-980DL GA-980DL XEROX English user manual 1
20 153-500-980DL GA-980DL XEROX Back Label 1
21 999-XF0-GA980DL GA980DL XEROX ass’y Color : 877C+K2440 1
22 899-400-GA980DL GA-980DL Control Board Ass’y 1
23 200-701-GA780 Control PCB 1
24 401-270-0205 Tact SW 2P 6*3.5 TSHB-2P S1.,S2.,S3.,S4.,S5., 5
25 630-008-C001 JST 1.5mm HEADER ZR S8B-
ZR
J1, 1
26 622-10A-1001 Jumper 0.56D 10mm(PTS) JP1.,JP2.,JP3., 3
27 520-005-L317-FLED 3D2P D1., 1
28 631-001-4060 4.3D+107#18 BLK 75mm+TIN2.5 Control+Ground wire 2
29 705-590-950F 19" FUJI FLC48SXC8V-10 1
30 849-40M-0770-CPS976 Inverter 1
31 899-000-GA980DL-UGA-980DL Main Board Ass’y Fujitsu 1
32 200-100-776D-CMain Board 1

17
NO
Parts No. Description Part Location Q’ty
33 281-031-20014 SMD R 2K 1% 0603 R87., 1
34 281-031-62014 SMD R 6.2K 0603 R86., 1
35 281-035-0R04 SMD R 0 ohm 5% 0603 R154.,R155.,L1.,L2.,L3.,L4.,L5.,L6., L7.,R17.,L19.,R5.,R7.,R36.,R71.,
R75.,R88.,R55.,R13.,R23., 20
36 281-035-1014 RES 100 5% 1/10W 0603 R25.,R26.,R27.,R28., 4
37 281-035-1024 RES 1K 5% 1/10W 0603 R60.,R61., 2
38 281-035-1044 RES 100K 5% 1/10W 0603 R44., 1
39 281-035-1554 SMD R 0603 1.5 Mohm R43., 1
40 281-035-2704 SMD R 27ohm 5% 0603 R200.,R201.,R203.,R204.,
R206.,R207.,R209.,R210., 8
41 281-035-2734 SMD R 27K 0603 R96., 1
42 281-035-3014 SMD R 300 ohm 0603 R95.,R98., 2
43 281-035-3304 SMD R 33 ohm 0603 R608.,R611.,R612.,L18.,R58.,
R59.,R73.,R76.,R77., 9
44 281-035-3314 SMD R 0603 330 ohm R56.,R57., 2
45 281-035-3324
SMD R 3.3K 0603 1/10W 5%.
R35.,R39.,R40., 3
46 281-035-4704 SMD R 47 ohm 0603 R18.,R19.,R6.,R8.,R9., 5
47 281-035-4724 SMD R 4.7 K 0603 R2.,R33.,R78.,R81.,R89.,R91.,R92.,
R93.,R150.,R152.,R153.,R158., 12
48 281-035-4734 SMD R 47K 0603 R3.,R4.,R41.,R12.,R14., 5
49 281-035-5614 SMD R 560 ohm 0603 R42. 1
50 281-035-6814 SMD R 0603 680ohm R97.,R94., 2
51 281-035-7504 SMD R 75 ohm 0603 R202.,R205.,R208.,R211.,R16.,R21.,
R24., 7
52 281-035-7534 SMD R 75K 0603 R84., 1
53 282-330-2454 SMD R ARRAY 33 ohm 1206 RP1.,RP2.,RP3.,RP4.,RP5.,RP6.,RP7.,
RP8.,RP9.,RP10.,RP11.,RP12.,RP13., 13
54 330-100-16255 5mmEC 10uF 16V 105C M TP C195.,C125., 2
55 330-101-16255 5mmEC 100uF 16V 105C M TP C85.,C94.,C97.,C123.,C129., 5
56 330-220-16255 EC 22uF 16V 4*5 105C C91., 1
57 330-221-16255 EC H:5mm 220uF 16V 105C M C104.,C107.,C109.,C112.,C115.,C120.,
C128.,C197.,C198.,C101., 10
58 381-180-032554 CMD CC NPO 18pF 25V 0603 C28.,C29., 2
59 381-220-032554 SMD CC 22pF 25V NPO 0603 C12.,C13.,C18.,C19.,C80.,C81., 6
60 381-301-032554 SMD CC NPO 25V 300PF 5% 0603 C110., 1
61 381-5R0-032554 SMD NPO 5P 25V 0603 C2.,C6.,C9., 3
62 382-102-032564 SMD CC 1000pF/25V X7R 0603 C26., 1
63 382-103-032564 SMD CC 0.01uF/25V X7R 0603 C501.,C75.,C99.,C103.,C106.,C114.,
C122.,C124.,C130.,C10., 10
64 382-392-032564 X7R 3900pF 10% 25V 0603 C22., 1

18
NO
Parts No. Description Part Location Q’ty
65 382-392-032564 SMD CC 0.039uF 25V X7R 0603 C22., 1
66 382-393-032564 SMD CC 0.047uF 25V X7R 0603 C23., 1
67 382-473-032564 SMD CC 0.047uF 25V X7R 0603 C24.,C25.,C27., 3
68 385-104-032584 SMD CC 0.1uF 25V Y5V 0603
C5.,C193.,C194.,C1.,C4.,C8.,C11.,C14.,
C15.,C16.,C20.,C21.,C30.,C31.,C32.,
C33.,C34.,C35.,C36.,C37.,C38.,C39.,
C40.,C41.,C42.,C43.,C44.,C45.,C46.,C47.,
C48.,C49.,C50.,C51.,C52.,C53.,C54.,
C55.,C56.,C57.,C58.,C59.,C60.,C62.,
C63.,C64.,C65.,C66.,C67.,C68.,C69.,
C70.,C71.,C72.,C73.,C74.,C76.,C77.,
C78.,C79.,C86.,C92.,C93.,C95.,C96.,
C98.,C100.,C102.,C105.,C108.,C111.,
C113.,C116.,C117.,C118.,C119.,C121.,
C126.,C127.,C131.,C199.,C200.,C201.,
83
69 409-003-0110 DC Jack 3.5D SCD510 CN3., 1
70 483-002-104S6 Connector Pin Pitch
2.54mm 1*4 Pin
J2., 1
71 485-415-S070 D-SUB 3R15 180D H6.8 Blue CN14., 1
72 485-D25-S118 DVI-D connector 11.40mm CN15., 1
73 506-0AI-C1084 SMD REG. AIC1084CM 3.3V 5A U14., 1
74 506-0CS-5828 SMD 85M LVDS CS5828+TQFP56 U9.,U10., 2
75 506-1LM-3485 LM3485/NS MSOP-8 U13., 1
76 506-524-LC21 Memory IC 24LC21 SMD U2.,U1., 2
77 506-5EN-29LV8 Flash 8M EN29LV800T-70RTC/EON U6., 1
78 506-5NM-24C16 Linear OC NM24C16M-8 (SMD) U8., 1
79 506-774-LCX14 SMD Hi Speed TTL 74LCX14 U3., 1
80 506-774-LCX541 74LCX541 TSSOP-20 FAIRCHILD U7., 1
81 506-CPW-131A-20
Scaler IC PW131A-20Q U4., 1
82 506-RLD-1117-ALD1117-ADJ-A UTC SOT223 U15.,U16., 2
83 518-02N-3904 TR. 2N3904 SMD Q1.,Q2.,Q3.,Q4.,Q5.,Q7.,Q8.,Q9., 8
84 518-02N-3906 SMD TR 2N3906 Q10., 1
85 518-1CE-9435 MOSFET CE9435A CO8 U11.,U12.,U17., 3
86 522-030-B340-TSCHOTTKY SB340 TP D14., 1
87 528-2BA-T54C SMD Diode BAT54C SOT23 D4.,D1., 2
88 529-350-05R6 SMD Zener 5.6V MMSZ5232B D15., 1
89 531-143-49US XTAL 14.318Mhz LC=16pF 49US Y1., 1
90 558-352-5000 SMD Fuse 1206 24V 5A F1., 1
91 630-006-1008 Base 6P JWT A2001
Pitch 2
CN4., 1
92 630-008-C001 JST 1.5mm HEADER ZR S8B-
ZR
CN1., 1

19
NO
Parts No. Description Part Location Q’ty
93 630-030-8001 Connector 125HR(DF14) 30P1.25 SMD
CN2., 1
94 745-330-2062-333uH C4426-060128YB-UL L27., 1
95 780-103-3000 SMD BEAD SBK160808-300Y L13.,L14.,L15.,L16.,L17.,L20., 6
96 780-104-6010 SMD Bead SBK-201209T-601Y-SL199.,L21.,L29.,L30.,L31.,L32.,L35.,
L36.,L37.,L38., 10
97 780-107-121K50 Bead 120ohm 1206 5A FBM-
11
L22.,L24.,L26.,L28.,4
98 780-112-8000 Bead HCB4532K-800T60 80ohm6A L25., 1
99 781-220-0462 L 0805 22uH CL201212T-
220K
L8.,L9.,L10.,L11.,L12., 5
100
152-000-SH570 TOSHIBA DC Jack Support NYLON CN3., 1
101 281-035-2224 SMD R 2.2K 0603 R171.,R29.,R69., 3
102
281-035-1034 RES 10K 5% 1/10W 0603 R15.,R212.,R22.,R45.,R46., R47.,R48.,R49.,R50.,R51.,R52.,
R62.,R80.,R601,R605, 15
103
506-XMK-1707 展頻IC MK1707/ICS SOIC-8 U22., 1
104
902-GA0-A000 GA980DL XEROX
Color : 877C+K2440 1
105
151-A00-Q906A GA980DL Front bezel ABS HB K2440 1
106
121-500-980D GA980DL Rear Plate SECC1.0 1
107
123-001-776DT-A
Connector Cover 1
108
154-002-782S4 GA980DL Tuner Cover Color : 877C 1
109
154-001-GA580S4
GA980DL Key Top Color : 877C 1
110 154-500-980DL GA-980DL CR Bar L Color : 877C 1
111 154-501-980DL GA-980DL CR Bar R Color : 877C 1
112 154-002-GA580 GA-980DL LED Lens 1
113 928-200-980DL GA980DL Glass 2.8t
+AG XEROX
1
114 540-600-976DA Insulation For Panel back side 1
115 540-700-1976 Mylar Film AS/PS976 0.2t 1
116 540-600-976DB Insulation Rear Plate inside 1
117 154-502-980DL GA-980DL PVC film 0.3t 1
118 126-500-976D 976D Hinge 1
119 123-500-0980 AL Base 980/PS976D Color : 877C 1
120
155-001-PS576-AGA980DL Cushion 5
121 106-006-4033-1Screw I4*6 ISO 2
122
107-005-3032 Screw B3*5 ISO 6
123
107-006-3032 Screw B M3xL6 ISO 2
124
107-008-3032 Screw M3xL8 ISO 2
125
103-008-4033 Screw F3*8 NI 1
126
101-009-3013 Screw P3*L9mm TP1 2

20
NO
Parts No. Description Part Location Q’ty
127
101-010-4033-1Screw P4*10 ISO 2
128
132-300-PS576 Base Screw Ass’y 1
129
106-012-6033 Screw M6 L 12mm 1
130
132-001-PS576-ASpringe 1
131 631-030-J976 30P 1.25-1.0 130mm 1
132
631-006-7008-AWire 150mm 1
133
126-030-ALP4 AL Foil 200x30mm 2
134
126-030-ALP7 AL Foil W30*L90mm 1
135
126-030-ALP AL Foil 150x30mm 1
136
631-008-G976 8P1.5 220mm+CORE加SHIELD+GND 1
137
101-010-3012 Screw P3*L10mm TP1 10
138
105-008-3012 Screw T3*8mm TP1 3
139
831-411-00405 Sponge 11x405.2x2mm 2
140
831-411-00323 Sponge 11x323.5x2mm 2
141 123-507-976D AL Neck Color : 877C 1
142
123-502-976D NECK 1
143
151-051-980DL GA-980DL XEROX rear cover 1
144
109-950-0950 Screw For D-SUB Connector 2
145
109-948-1000 Screw For D-SUB Connector 2