XKGlow XK041002 User manual

!!!!!XK041002!/!XK041005!!!Single!Color!Undercar!&!Interior!Kit!!!!!!!!!!!!!!!!!!!!!!!!!!! !
!
!
1!
Warranty and Disclaimer
Within One year after the purchase date, the original buyer may return any XKGLOW products that has
one or more LEDs that fail to illuminate, due to a defect in materials or workmanship.
Installation of this product must be performed by a licensed professional. Should the failure of the product be
the result of damage occurring as a result of improper installation, alteration of the product or an act or omission
on the part of the consumer, this warranty is void. XKGLOW Lighting shall not be responsible for any
consequential damages which arise from the use and/or installation of the product. If the kit is installed in any
manner other than specified, XKGLOW Lighting reserves the right to deny any warranty claims at the discretion
of the technical support department. Any product return must include the original packaging, invoice number and
a statement of the alleged defect. Upon receipt of the returned product, the company will test the product for
defect. If the results of the testing do not support the warranty claim, do not reveal any defect or indicate
consumer negligence in the installation and handling of the product, then the product will be returned to you and
you will be charged a reshipping fee. If the product is returned from an address within the continental United
States, within the first 30 days after purchase, and is found to be defective, XKGLOW Lighting will exchange or
refund the original purchase expense. This offer does not extend to the cost for shipping charges on any
international packages.
Additional Disclaimer Terms
Please check your local and state laws for the proper use of this product.
• Improper installation of electrical products such as lighting may cause damage to any vehicle or device to
which the improperly handled or installed lighting is attached.
• Improperly installed product may cause electrical injury to persons.
• It is recommended that the kit should be installed by a licensed professional.
• XKGLOW assumes no liability for the installation of the product.
• Warranty or liability will not exceed the product purchase price, which shall be buyer’s sole and exclusive
remedy.
Return/Exchange Procedure
1. Email [[e-mail]] to notify us of the product issue as well as the item number and name of customer
on invoice.
2. We will send you the trouble-shooting guide to fix the issue, or to narrow down which of the component(s)
need to be replaced. If the issue still exists, we will ask you to send back the defective items to be replaced.
3. Please send the returned item as instructed, along with claims and a telephone number where you can be
reached.
4. After the returned item(s) have been accepted and inspected, we will issue a refund or replace the items
ASAP. For refunds, item(s) must be sent to XKGLOW within 14 days from date of purchase. Original shipping
charges are not refundable.
We always stand behind our products and are committed to our customers! For questions you may have,
please contact [email protected]. We normally respond within 24 hours. (Monday-Friday).!
Recommended Mounting Locations

!!!!!XK041002!/!XK041005!!!Single!Color!Undercar!&!Interior!Kit!!!!!!!!!!!!!!!!!!!!!!!!!!! !
!
!
2!
Mounting Instructions
1. Test all components before mounting: As shown below, plug all light units together and connect them to
the controller. Plug the controller into 12V car cigarette lighter socket. Turn on the switch and push the Mode
button to exam all the lights. If the light has any defective issue, please contact us and we will be happy to
replace them for you.
2. Plan mounting locations: Disconnect the tested lights and remove any bodywork that will have the LED
lights located behind them. Clean the mounting surface. LOOSELY mount the LED lights using Scotch or
painters tape (not included) to the desired locations. (DO NOT firmly attach the lights in this step.) Drill
mounting screw holes based on the planned spots.
3. Mount the lights: Clean the mounting surface again. Use the included double side tape pads to attach the
lights to the planned locations. Apply the included screws and mounting brackets to firmly mount all tubes to
the surface (required). Connect all Y-splitters, extension wires and the switch wiring harness.
4. Secure all wires and connectors: Neatly mount and hide any loose wires.
Use provided 3M tape to tape every connector together. Make sure the
wires and light tubes are not touching anything hot or located on moving
parts. Cover the end of each tube with provide end cap.
5. Connect to 12V DC power: Firmly connect the wire terminals to the
power socket and enjoy the light.
Visit www.XKGLOW.com to purchase extra lights and accessories.