Xo XOPIZZACART1 User manual

MANGIARE!
XOPIZZACART1
ASSEMBLY INSTRUCTIONS

dimensions
IMPORTANT:
THE FINAL ASSEMBLED OVEN AND CART HAVE A COMBINED WEIGHT OF 462lbs
39 3/8”
1000mm
78 7/8”
2003
5 1/8”
130mm
25 7/16”
646mm
9 5/16”
237mm
24”
610mm
35 5/8”
905mm
56 9/32”
1430mm
30 5/16”
770mm
19 3/32”
485mm
34 1/4”
870mm
10”
255mm

fasteners included
You will need help to support the cart during assembly and team lift the oven.
USE THE PACKING MATERIAL YOUR XOPIZZACART1 ARRIVED IN TO PAD AND
CUSHION THE PARTS DURING ASSEMBLY AND PREVENT SCRATCHES TO THE
FINISH!
(16) M6 x 15 Phillips Head Screws
(16) M6 x 18 Flat Washers
(16) M6 Hex Nuts
(26) M5 x 10 Phillips Head Screws
(4) M4 x 10 Phillips Head Counter Sunk Screws
(4) M4.2 x 15 Phillips Head Self Tapping Screws
You Will Need:
A Phillips Head Screwdriver
An Adjustable Wrench
(or a 10mm Wrench)
and Large, Strong Friends
who will work for pizza
to help pick the oven up...

1. ATTACH THE FOUR (4) CASTERS TO THE BASE.
Locate the base and (2) wheel supports.
Align the bolt holes on the wheel supports
with the bolt holes on the base.
Using the M6 x 15 Phillips head screws supplied,
insert (4) screws in the first corner of the base,
through a wheel support - then through one of the casters.
Place a flat washer onto each of the (4) screws and
thread one of the M6 x 15 nuts on to hold it in place.
DO NOT TIGHTEN YET.
Repeat this for the remaining casters.
Once all (4) casters are in place -
using a Phillips Head Screwdriver and 10mm or
adjustable wrench, tighten all of the (16) nuts.
Check to make certain that all are tight before
proceeding.
NOW SET THE WHEELED BASE RIGHT SIDE UP - READY FOR THE NEXT STEP
building the cart
Use two people to support the cart during assembly.
LOCKING CASTERS SWIVEL CASTERS
MUST BE ON THE LEFT MUST BE ON THE RIGHT

building the cart
Use two people to support the cart during assembly.
2. ATTACH THE LEFT SIDE PANEL. (side with the sliding shelf opening)
Locate the left side panel, it has a rectangular slot for the shelf.
Being careful not to scratch the finish, align the bottom of the left side with the wheeled base.
While one person supports it, attach the side panel to the base using (4) M5 x 10 screws.
Once all (4) screws are in place - using a Phillips Head Screwdriver and 10mm or adjustable
wrench, tighten all of the (4) nuts.
Check to make certain that
all are tight before proceeding.
3. ATTACH THE MIDDLE SHELF
Locate the cut outs halfway up on the left side panel.
Being careful not to scratch the finish, align the middle shelf with the cut outs and insert the
middle shelf.
While one person supports it, attach the side to the middle shelf using (4) M5 x 10 screws.
Once all (4) screws are in place - using a Phillips Head Screwdriver and 10mm or adjustable
wrench, tighten all of the (4) nuts.
Check to make certain that
all are tight before proceeding.

building the cart
Use two people to support the cart during assembly.
4. ATTACH THE RIGHT HAND SIDE
Locate the right hand side, while supporting the middle shelf to avoid scratches -
align the cut outs on the right side and attach to the middle shelf and base using
(8) M5 x 10 screws.
DO NOT TIGHTEN UNTIL ALL THE SCREWS ARE IN PLACE.
Make certain all the screws are tight before proceeding.
5. ATTACH THE TWO (2) TOP CROSSBARS
Locate the two top crossbars - the shelf glides are already attached.
Align one so the open end of the glide is in line with the square slot in the left side.
Bolt the crossbar in place with (4) M5 x 10 screws. Repeat with the other crossbar.
DO NOT TIGHTEN UNTIL ALL THE SCREWS ARE IN PLACE.
Make certain all the screws are tight before proceeding.

building the cart
Use two people to support the cart during assembly.
6. INSTALL THE SLIDING SHELF
Extend the telescoping shelf supports attached to the top rails through the square slot to
expose the screw holes for attachment.
Remove the protective plastic sheet from the stainless steel shelf.
Align the screw holes in the telescoping shelf supports with the holes in the side of the shelf.
Attach to the shelf to the supports using (4) M4 x 10 countersunk head screws.
DO NOT TIGHTEN UNTIL ALL THE SCREWS ARE IN PLACE.
Make certain all the screws are tight and you are ready for the oven!

setting the oven
THE OVEN IS VERY HEAVY! TEAM LIFT TO AVOID INJURY OR DAMAGE!
7.
SETTING THE OVEN
WARNING - Be aware of pinch points and make
place the oven safely.
Remove the door and place safely out of the way
before lifting.
The cart has centering tabs designed to match
precisely with the oven - pay close attention
to these tabs during the lift and placement.
8. ATTACH THE CHIMNEY
After the oven is securely in place,
fit the chimney to the outlet in the top
of the oven.
The chimney has interlocking tabs
that will hold it securely in place
while allowing it to be removed
if you wish.
Alternately - you may choose to
attach the chimney using the
(4) 4,2 x 16 self-tapping screws
supplied.

setting the oven
THE OVEN IS VERY HEAVY! TEAM LIFT TO AVOID INJURY OR DAMAGE!
9. FIT THE CHIMNEY CAP
The Chimney Cap simply slips into place - AND YOU ARE READY TO FIRE UP!

the optional tool holder
The Optional Tool Holder is supplied with the XOPIZZATOOL3 Set
JUST TWO BRACKETS TO ATTACH
The convenient tool holder is designed to screw directly to your XOPIZZACART1 and keep
your large peel, small peel and brush close at hand. It even has a built-in bottle opener.
The Top Bracket and Bottom Bracket each attach with two M5 x10 Phillips Head screws.

optional accessories
A great pizza oven needs the right tool set.
The XOPIZZATOOL3 set of tools is exactly
what you need to start cooking like a professional.
Contains:
(1) Large Pizza Peel for adding and removing
pizza from the oven
(1) Small Pizza Peel for rotating or moving pizza
and other dishes in the oven
(1) Metal Brush for clearing ash and debris from
the fire away from the cooking area.
(1) Handy Tool Holder Brackets designed to
mount directly to the XOPIZZACART1.
And to help protect your investment -
All Weather Covers for your
XOPIZZA4 Oven.
Choose the style to fit either
Counter Top (XOGCOVER40PI)
Freestanding (XOGCOVER40PF)
Your XOPIZZA4 comes with a
Stainless Steel Door but there
is an optional GLASS DOOR
(XOPIZZA4GD) which allows
you to keep an eye on the fire
and food while it cooks while
conserving heat.
...and of course,
It also allows you to enjoy the
ambiance of fire.