XOTIK XTX200 User manual

V1.0 ©2019 XOTIK
XOTIK XTX200 2.4GHz Radio Control System
Instruction Manual
IMPORTANT! Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. This manual contains instructions for safety, operation, and maintenance. It is
essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or
use, in order to operate correctly and avoid damage or serious injury.
NOTICE: All instructions, warranties, and other collateral documents are subject to change at the sole
discretion of XOTIK. For up-to-date product literature, please visit www.xotikmodel.com.
FEATURES
2.4GHz Spread Spectrum Technology
Built in failsafe function
Push button steering trim
Ergonomic drop wheel design

V1.0 ©2019 XOTIK
SPECIFICATIONS
XTX200 TRANSMITTER XRX200E RECEIVER
Channels: 2 Channels: 2
Frequencies: 2.405 –2.475GHz Frequencies: 2.405 –2.475GHz
Modulation: FHSS spread spectrum Modulation: FHSS spread spectrum
Input Power: 2.20 –3.0V DC Input Power: 2.9 –4.2V DC
Output Power: <0.1W Power On Indicator: LED
Power On Indicator: LED
SAFETY PRECAUTIONS
IMPORTANT! Always follow these instructions when operating this system.
Do not modify or alter this system.
The system is suitable for ages 14 and above.
Switch off the transmitter and take out the battery when it is not in use.
Do not operate near people or animals.
Do not allow any water or moisture to make contact with the system.
Before operating, examine all parts for damage. If any is found, do not operate until the
damage has been repaired.
Use a clean cloth to wipe the transmitter clean.
Keep the transmitter and batteries away from direct sunlight and/or heat sources.
Visit www.xotikmodel.com for repair guides and replacement parts.

V1.0 ©2019 XOTIK
FCC STATEMENT
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC Rf Radiated Exposure Statement: This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20cm between the radiator (transmitter) and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLANCE COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
FCC ID:2AS4Q-XTX200
BATTERY REQUIREMENT
The transmitter requires two 1.5V AAA size batteries (not included).
Do not power transmitter by mixing different types of batteries, or old and new batteries.
Use only batteries of the same or equivalent type as those recommended.
IMPORTANT! Do not operate with weak batteries as it could result in reduced range and/or
possible loss of control.
TRANSMITTER SETUP

V1.0 ©2019 XOTIK
Remove the safety screw and press the lever at the base of the handle to swing open the battery door.
Install the two batteries according the orientation stated inside the battery compartment. After battery
installation, close battery door and tighten safety screw.
Press in the power button on the top of the transmitter. The LED around the power button will glow
after power on. If not, power off the transmitter and re-check the installation of batteries. A flashing
LED means low batteries and needs to be replaced.
IMPORTANT! Always power on the transmitter first and the receiver second. Your transmitter will
automatically link (connect) to your receiver. If you are running two or more receivers at the same time
be sure to power on the receiver one at a time. If not you may link to the wrong transmitter.
RECEIVER SETUP
Mount the receiver as stated in the model’s instructions.
IMPORTANT! Always power on the transmitter first and the receiver second. Your transmitter will
automatically link (connect) to your receiver. If you are running two or more receivers at the same time
be sure to power on the receiver one at a time. If not you may link to the wrong transmitter.
STEERING TRIM CONTROL
The center point of the steering can be finely adjusted as needed to get the best control of the model.
Press either of the two ST TRIM button on the top control panel of the transmitter to adjust the left and
right center trim of the model.
The center position of the steering can be identified when the LED flashes briefly while the left or right
trim is being adjusted.
FAILSAFE
A failsafe function is built into the transmitter system. If the link between the transmitter and receiver is
broken, both steering and throttle will return automatically to the center position. To re-established
normal function, both transmitter and receiver will need to be power cycled (turned off, then turned
back on).

V1.0 ©2019 XOTIK
POWERING THE SYSTEM
IMPORTANT! Always power on the transmitter first, then power on the receiver. Always power off the
receiver first, then power off the transmitter. Never power off the transmitter while running the model.
CARE AND MAINTENANCE
After each run, examine all parts for damage. If any is found, do not operate until the damage
has been repaired.
Use a clean cloth to wipe the transmitter clean.
Keep the transmitter and battery away from direct sunlight and/or heat sources.
For long term storage, we recommend removing the transmitter batteries to avoid unwanted
corrosion.
REPLACEMENT AND OPTION PARTS
For a complete list of replacement and option parts, visit www.xotikmodel.com.
WARRANTY AND PRODUCT SUPPORT
Do not return your product to the place of purchase. XOTIK will repair or replace factory defects for 30
days from the date of purchase. This warranty specifically does not cover crash damage, misuse, or
abuse. To make a warranty claim, please contact our product support team at
[e-mail]. This warranty applies only if the product is operated in compliance
with the instructions and warnings provided with this model. XOTIK assumes no liability except for the
exclusive remedy or repair of parts as specified above. XOTIK shall not be liable for consequential or
incidental damages.
If you have any questions, please contact: [e-mail]
XOTIK
Guangzhou Youli Plastic Manufacture Co., Ltd
No.7 The Keer Road, Dongchong Town, Nansha, Guangzhou 511475, Guangdong, China
Tel: [phone]
Fax: [phone]
Made In Guangzhou, Guangdong, China

FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 10mm must be maintained between
the user’s body and the handset, including the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any metallic
components. Body-worn accessories that do not meet these requirements may not comply
with RF exposure requirements and should be avoided. Use only the supplied or an approved
antenna.