XPower XD-85LH User manual

Low Grain Refrigerant
Dehumidier Owner's Manual
LGR Deshumidicador
Manual de Usuario
LGR Déshumidicateur
Manuel d'Emploi
Model / Modelo / Modèle:
XD-85LH, XD-85L2
(115V 60Hz)
Lea y guarde estas instrucciones
Lisez et gadez ces instructions
Read and save these instructions
www.xpower.com | 1-(855)-855-8868 | [e-mail]
Index: NA-1-A1
Edition: 6.1.Final

English - 2
Safety Instructions
WARNING - READ AND SAVE THESE INSTRUCTIONS BEFORE USING THIS
PRODUCT.
The user of electrical products may create hazards that include, but are not limited to
injury, fire, electrical shock. Failure to follow these instructions may damage and/or
impair its operation and void the warranty.
• Before operating, remove all packaging material and check for any damage that may
have occurred during shipping or any missing items.
• Check household power supply to ensure it matches the appliance’s specification.
• DO NOT operate the appliance with a damaged cord or plug. Discard or return to an
authorized service facility for examination and/or repair.
• DO NOT use an extension cord with this appliance. Use only with GFCI protected
receptacles. Contact a qualified electrician for verification or installation of a GFCI
receptacle if necessary.
• DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or
similar coverings. DO NOT route cord under furniture or appliances. Arrange cord away
from traffic area and where it will not be tripped over.
• To reduce the risk of fire or electric shock, DO NOT use this appliance with any solid
state speed control device.
• DO NOT touch this appliance or the plug with wet hands or while standing in water.
• DO NOT operate the appliance near any pooled water.
• DO NOT use the product in areas where gasoline, paint or other flammable goods and
objects are used or stored.
• DO NOT insert or allow objects to enter any ventilation or exhaust opening as this may
damage the appliance and void the warranty.
• DO NOT cover the air inlet or outlet on the appliance.
• DO NOT direct the air flow at human faces or bodies.
• DO NOT allow children to play with this appliance.
• AUTOMATICALLY OPERATED DEVICE – To reduce the risk of injury, disconnect from
power supply before servicing.
• Remove the power cord from the electrical receptacle by grasping and pulling on the
power cord plug-end only, DO NOT pull the cord directly.
• DO NOT attempt to repair or adjust any electrical or mechanical functions of this
appliance, as this may cause danger and void the warranty.
• If the appliance is damaged or it malfunctions, DO NOT continue to use it. Unplug the
product from the electrical outlet. Refer to troubleshooting guide or contact XPOWER.
• Store in a dry area, away from exposure to sunlight, extreme temperature and humidity,
or other extreme environment, when not in use.
• DO NOT stack this appliance to more than three units.
• Always grip the trolley handle and keep the unit up when transporting from room to
room. DO NOT tilt the product on its side or upside down.
• If the dehumidifier was transported tilted on its side or upside down, you must position
it upright and wait at least 4 hours before using it again.
• An electronic instruction manual can be obtained through manufacturer’s website
www.xpower.com.
!

English - 3
LGR Dehumidier Introduction
• XPOWER LGR (Low Grain Refrigerant) Commercial Dehumidifiers are designed to
maximize water extraction while combining the highest efficiency in performance and
portability.
• Latest technology and a high efficiency extraction process ensures peak performance
in even the most challenging environments, such as extreme temperature and low
environment humidity.
• With high efficient water removal capacity, the LGR (Low Grain Refrigerant)
Dehumidifier allows an extreme dry zone in the working area and water migration to
the air from all the surfaces. It is ideal for water damage restoration and industrial
applications where maximum air drying performance is needed.
Items Included
Dehumidier Owner's Manual
Model:
XD-75L, XD-85L
(115V 60HZ)
Readand save these instructions before use
www.xpower.com| 1-(855)-855-8868 | [email protected]
Index:NA-1-A1
Edition:1.1.Alpha
Dehumidifier x 1
Drain Hose x 1
Owner’s Manual x 1

English - 4
Parts Description
Hand Carry
Handle
Secondary
Filter
Trolley
Handle
Hand Carry
Handle
Secondary Filter Case
Primary Filter
Secondary
Intake
Primary
Intake (Grille)
Drainage
Outlet
Control
Panel
Ducting
Frame
Exhaust
(Grille)
Hand Carry
Handle
Compartment*
Hand Carry
Handle
Trolley
Handle
Wheels
Hangers
FRONT
REAR
* These features do not apply to all models mentioned in this manual.

English - 5
• Positioning: Before using the dehumidifier, place the unit UPRIGHT for at least 1
hour before use to allow the refrigerant to stabilize. If the unit was tilted on its side or
upside-down during transportation, set the unit UPRIGHT for at least 4 hours before
use. The dehumidifier must be positioned UPRIGHT on a level surface during use.
• Enclosed Area: For optimal efficiency, the dehumidifier must be operated in an
enclosed area. Keep all doors, windows and other outside entrances to the room
closed. Turn off the air conditioning.
• Air Circulation: It’s suggested to have a constant efficient air circulation inside the
area that you are going to work in, for example, setting up a circulation with XPOWER
Air Mover combinations.
• Environment Temperature/Humidity: The dehumidifier is designed to work in an
environment with a temperature of 33 °F to 105 °F (0.6 °C to 40.6 °C) and relative
humidity level of 20% and higher. The dehumidifier may not function normally or
efficiently if the room temperature and humidity level exceed this temperature and
humidity level range.
• Power Cord and Drain Hose: The power cord has a length of 25 feet (7.5 meters) and
the drain hose has a length of 40 feet (12 meters). Select a location where the power
cord can reach the power source and the drain hose can reach the area you want.
Please do not lift the drainage hose higher than 16 feet (5 m) above the machine.
• Inlet and Outlet Orientation: Also pay attention to the orientation of the air inlet and
air outlet. Make sure the airflow won’t influence any object nearby the dehumidifier.
• IMPORTANT: The effectiveness of the dehumidifier can be influenced by different
factors. You should keep any new moisture-laden air away from the working area and
allow sufficient enclosed air circulation in the room. You may also find that installing
multiple dehumidifiers may be required for larger enclosed areas.
Selecting a Location (Important)
Installation and Operation Guide

English - 6
Installation and Operation Guide (Continued)
Control Panel
Drain Hose
Drain Hose Installation
• Attach the drain hose
inlet to the drain outlet
of the machine.
• The machine’s outlet
can be found as the
graph on the left.
• Please have a separate
container to collect the
water coming from the
other end of the drain
hose.
Press to
Install/Release

English - 7
Installation and Operation Guide
Extension Setup (Optional)
(Continued)
①
②
③
①, ⑤
②
③
④
Intake Ducting*
① Install the intake adapter**.
② Screw on the four screws.
① Screw off the two screws.
② Take out the ducting frame.
③ Let the ducting hose go through the
ducting frame.
③ Attach the ducting hose to the intake
adapter.
④ Turn the ducting hose around the
frame to its back.
⑤ Reinstall the ducting frame and screw
on the two screws.
* For model XD-85LH only.
** The intake adapter is sold separately.
Exhaust Ducting (Lay Flat) (12 inch/30.5 cm Diameter)

English - 8
Relative Humidity Display
This will show the relative humidity level of the setting or environment. As default, it
displays the environment humidity. When adjusting humidity, it will display the setting
humidity and blink. After 5 seconds from the last adjustment, it will display the
environment humidity again. (See Page 8: Humidity Control)
CT
F/C
:
°C
%RH
TOTAL TIME
Installation and Operation Guide (Continued)
Control Panel
CT
F/C
:
°C
%RH
TOTAL TIME
Temperature DisplayPower Control
Evaporator
Coil/
Environment
Temperature
Switch
Fahrenheit/Celsius
Scale Switch
Relative Humidity
Display
Total Running Time
Humidity Control
Fan Speed Manual Drainage
Power Control
Press to switch the dehumidifier ON or
OFF.
CT
F/C
:
°C
% RH
TOTAL TIME
Fahrenheit/Celsius Scale Switch
Press to switch the display of the
temperature in Fahrenheit or Celsius
scale.
CT
F/C
:
°C
% RH
TOTAL TIME
Manual Drainage
Press to drain manually. Manual drain
will last for 45 seconds. [See Page 11:
Drainage (Important)]
CT
F/C
:
°C
% RH
TOTAL TIME
Humidity Control
Tap “+”/“-” to increase/decrease the
desired humidity level by 1% increments.
Touch and hold to increase/decrease the
setting humidity level by 5% per second.
The adjustable range is 30% to 90%.
CT
F/C
:
°C
% RH
TOTAL TIME
CT
F/C
:
°C
% RH
TOTAL TIME
Evaporator Coil/Environment
Temperature Switch
Press to switch the display of the
temperature of the evaporator coil or
environment.
CT
F/C
:
°C
% RH
TOTAL TIME
Buttons
Information

English - 9
Temperature Display
This will show the temperature of the evaporator or environment (See Page 8:
Evaporator Coil/Environment Temperature Switch). When in Celsius scale, will
be illuminated. When in Fahrenheit scale, will turn off. If the temperature to show
is higher than 99 °F, the scale will be set to Celsius automatically (See Page 8:
Fahrenheit/Celsius Scale Switch).
CT
F/C
:
°C
%RH
TOTAL TIME
CT
F/C
:
°C
%RH
TOTAL TIME
CT
F/C
:
°C
%RH
TOTAL TIME
Installation and Operation Guide (Continued)
Control Panel (Continued)
Drainage Indicator Light
When this light blinks, it indicates the
machine is in drainage process. When
this light stays bright, it indicates the
water tank is full.
CT
F/C
:
°C
% RH
TOTAL TIME
"OFF" Light
This light indicates the machine is
connected to power source and it is now
turned off.
:
°C
%RH
TOTAL TIME
Constant Dehumidication
At the humidity level setting of 30%, if
humidity control button “-” is pressed,
will blink on the humidity display.
The machine will enter into constant
dehumidification mode and won’t
stop dehumidification as environment
humidity changes.
:
°C
%RH
TOTAL TIME
Error Codes , , ,
These are error codes. Please refer
to Troubleshooting Guide for more
information.
:
°C
%RH
TOTAL TIME
:
°C
%RH
TOTAL TIME
:
°C
%RH
TOTAL TIME
:
°C
%RH
TOTAL TIME
Fan Speed
This will show if the machine is running on low ( ) or high ( ) fan speed. The
dehumidifier will control the fan speed according to the environment temperature
and humidity.
CT
F/C
:
°C
%RH
TOTAL TIME
CT
F/C
:
°C
%RH
TOTAL TIME
CT
F/C
:
°C
%RH
TOTAL TIME
CT
F/C
:
°C
%RH
TOTAL TIME
Total Running Time
This will show the total running time from the first usage to the current moment.
Running time starts to count during the time when the machine turns on. The value
can’t be reset.
CT
F/C
:
°C
%RH
TOTAL TIME
Defrosting Light
This light indicates the evaporator coil or
environment temperature is too low. Frost
may start to appear on the evaporator
coil. The machine is now defrosting.
CT
F/C
:
°C
% RH
TOTAL TIME
Dehumidication Light
When this light blinks, it indicates
the machine is now preparing for
dehumidification. When this light stays
bright, it indicates the machine is now
dehumidifying.
CT
F/C
:
°C
% RH
TOTAL TIME
Indicators
:
°C
% RH
TOTAL TIME

English - 10
Installation and Operation Guide (Continued)
Start Your Job
Turn on the dehumidifier
Press the Power Control button to switch on the machine. You may see the
dehumidification light is flashing. Please wait for 3 minutes (180 seconds) until the
machine completes the startup.
Write down the starting time
Please remember to write down the starting time right after the machine
starts, if you want to calculate the usage time.
Set the desired humidity level
• Tap the humidity control button to adjust the setting humidity level. The default
humidity setting is 30%. The adjust range is from 30% to 90% (See Page 8: Humidity
Control). The machine will try to match the setting humidity level and maintain it.
• If you want the machine to work constantly, please adjust the humidity level down
to 30%, and then press “-” (See Page 9: Constant Dehumidification). Tap “+” to exit
constant dehumidification mode.
• If the dehumidifier loses power accidentally, when turned on again, the dehumidifier
will work on the last known configuration.
Dehumidification
• When the machine is dehumidifying, the dehumidification light goes on.
• You may see the dehumidification light is flashing. That means the dehumidification
temporally pauses or the environment humidity has reached the setting level. Please
wait until the machine completes the startup or until the humidity level rises up again.
• The dehumidifier will control the fan speed according to the environment temperature
and humidity.
Defrosting
• When the evaporator coil or the environment temperature is too low, frost may appear
on the evaporator. This will cause a lower effectiveness of the dehumidification. The
machine will start defrosting until the temperature goes back to normal.
• When the machine is defrosting, the dehumidification pauses. The dehumidification
light goes off, and the defrosting light will go on.
• Do not turn off the machine during defrosting process.
CT
F/C
:
°C
%RH
TOTAL TIME

English - 11
Installation and Operation Guide
Start Your Job (Continued)
Drainage (Important)
• Press the Manual Drainage button to process drainage manually. It will last for 45
seconds and won’t stop dehumidification or defrosting process.
• If the water tank is full or not positioned horizontally, the water tank full indicator light
will go on. Any dehumidification or defrosting process will pause and the machine will
automatically process drainage for 45 seconds. Afterwards, if the water tank is still
detected full, an error code will be displayed (See Page 9: Error Codes or Page 14:
Troubleshooting Guide).
• When turned off, the machine will automatically process drainage for 60 seconds.
Please wait until this process completes.
• Please do not lift the drainage hose higher than 16 feet (5 m) above the machine.
Calculate the usage time
• Please remember to write down the ending time right before the machine
shuts down.
• Compare the starting time and the ending time to calculate the usage time.
CT
F/C
:
°C
%RH
TOTAL TIME
(Continued)
Secondary Intake (Opened)
Secondary Intake (Closed)
Secondary Filter Case
Important: Close the secondary intake when environment temperature falls
under 68 °F (20 °C) or in contaminated environment for better efciency.
To close the secondary intake, remover the filter case, rotate and re-install.
!

English - 12
Turn off the dehumidifier
Press the Power Control button to switch off the machine. When turned off, the machine
will automatically process drainage for 60 seconds. Please wait until this process
completes.
Start Your Job (Continued)
Installation and Operation Guide
Transportation
(Continued)
Hand Carry
Handle
Hand Carry
Handle Lift with Hand Carry Handles
• Lift the dehumidifier with the
two hand carry handles on the
two ends on the top.
• Be aware of the weight of the
machine.
WARNING: do not use the
hanger as hand carry handles.
Wheels
Trolley Handle
Intake
Transport with Trolley Handle
• Lift the dehumidifier on the wheels
with the trolley handle.
• Pull to transport with the trolley
handle.
Before transportation, you should always:
• Process a drainage manually. Otherwise the water may spill and enter in core parts of
the machine during transportation. This may also void the warranty.
• Disconnect the machine from the power source.
• Remove all the extension setup and uninstall the power cord and drain hose.
!

English - 13
User Maintenance Instructions
Frequent maintenance is recommended on this appliance. Failure to follow the
maintenance instructions may cause failure of the appliance and void the warranty.
Before maintenance or storage, you should always:
• Process a drainage manually.
• Disconnect the machine from the power source.
• Remove all the extension setup.
Intake
Hanger
Intake
Hanger
Compartment
For XD-85LH:
• Remove the drain hose
from the outlet of the
machine.
• Open the velcro on the
hangers.
• Hang the drain hose and
power cord on the hangers
and close the velcro.
For XD-85L2:
• Remove the drain hose
from the outlet of the
machine.
• Open the velcro on the
hangers.
• Hang the drain hose on
the hangers and close the
velcro.
• Store the power cord
or the drain hose in the
compartment.
Organize the Power Cord and Drain Hose

English - 14
User Maintenance Instructions (Continued)
Store the machine
• Store the appliance in a dry and cool indoor place, away from direct sunlight as well as
chemicals and out of reach of children.
• IMPORTANT: make sure the machine is levelly positioned.
• If you want to stack this appliance, stack them on their tops with the same orientation.
• Do not stack more than three units of this appliance.
Clean the surface
• Use a damp cloth to wipe the surface of the housing. Do not clean the unit with water
directly.
• Do not clean the fins of the evaporator and condenser by yourself.
①
②
④
①
③
Store or Replace the Filters
① Screw off the two screws.
② Take out filter grille.
③ Slide off the primary filter
from the grille.
④ Take out secondary filter
case and the secondary filter
from the slot.
• Clean and wash the filters
with water.
• Store the filter in dry and
cool area in a sealed
container.
• Replace filters if necessary.

English - 15
Troubleshooting Guide
PROBLEM POSSIBLE CAUSE SOLUTION
Dehumidifier
does not start
No electricity. Check for power supply.
The power cord is not properly
plugged in.
Remove and reconnect the
power cord.
Dehumidifier
runs but humidity
level does not
decrease
The dehumidification system is
within startup process.
Wait for 3 minutes
(180 seconds) until the
dehumidification light stops
blinking.
The humidity level setting is
too high.
Decrease the humidity level
setting.
The working area is not
enclosed.
Make sure the area is tightly
sealed.
There are other sources of
humidity in the room.
Remove these sources or wait
until they completely volatilize.
The humidity level has reached
the setting level.
Decrease the humidity level
setting, set to constant
dehumidification mode, wait
until the humidity level rises up
again.
Dehumidifier runs
but humidity level
does not decrease
The machine was tilted and
wasn’t positioned upright for
enough time before use.
Position the machine upright on
a level surface and wait for at
least 4 hours before next use.
The air filter or air inlet/outlet is
blocked.
Remove blockage.
The environment temperature
is too low/high or the humidity
level is too low.
The dehumidifier is designed
to work in an environment with
a temperature of 33 °F to 105
°F (0.6 °C to 40.6 °C) and
relative humidity level of 20%
and higher. Make sure the room
temperature/humidity does not
exceed this range.

English - 16
Troubleshooting Guide (Continued)
PROBLEM POSSIBLE CAUSE SOLUTION
Water on the floor The drain hose is loose. Tighten the connection of the
drain hose.
Sudden noise The machine starts drainage
process.
The water pump can create
sounds during operation. This is
a normal sound.
Error Code: E2 Failure of the temperature
sensor.
The dehumidification can
function but you won’t be able
to see the temperature/humidity
on the screen. Contact XPOWER
for more assistance.
Error Code: E3 Failure of the humidity sensor.
Error Code: E4 Failure of the water pump Contact XPOWER for more
assistance.
The machine is not positioned
levelly.
Position the machine on a level
surface.
The drain hose is blocked. Remove blockage.
Error Code: E5 Failure of the defrost sensor. The dehumidification can
function but will defrost for 5
minutes every half an hour.
Contact XPOWER for more
assistance.
If troubleshooting does not resolve your problem, please contact XPOWER or other
parties authorized by XPOWER for further instructions.

English - 17
Technical Specication
MODEL NUMBER XD-85LH XD-85L2
Voltage / Frequency 115 V~60 Hz
Amperage 6.7 A
Operation Temperature/
Relative Humidity
Requirement
33 °F - 105 °F (0.6 °C to 40.6 °C) /
20% RH or higher
Rated Airflow 180 CFM
Speed Control Automatic
Water Removal Efficiency
105 °F (40.6 °C) / 20% RH 22 Pints (10.4 L)/day
Water Removal Efficiency
80 °F (26.7 °C) / 60% RH 85 Pints (40 L)/day
Water Removal Efficiency
90 °F (32.2 °C) / 90% RH 150 Pints (71 L)/day
Compartment Feature No Yes
Time Meter Up to 9999 hours 50 minutes
Filter Type Stainless Steel Filter
Cord Length 25 ft. / 7.5 m
Drain Hose Length 40 ft. / 12.0 m
Unit Dimension (L) x (W) x (H) 13.1 x 31.5 x 22.6 in. /
33.3 x 80.1 x 57.5 cm 13.1 x 32.3 x 22.5 in. / 33.2 x 82.1 x 57.1 cm
Unit Weight 71.0 lbs. / 32.2 kg 70.5 lbs. / 32.0 kg
Safety Certification ETL/C-ETL
If your product(s) is not listed above, please visit www.xpower.com for more information.

English - 18
1 YEAR LIMITED WARRANTY
XPOWER-branded products purchased in the U.S. from authorized distributors include
a 1-year limited warranty. Contact XPOWER to confirm warranty information about your
product(s).
This limited warranty covers defects in materials and workmanship in your XPOWER-
branded products, purchased in the U.S. ONLY. Local warranty policy (if any) in your
country will cover products purchased outside the U.S.
XPOWER Limited Warranty (USA)
Items mentioned but not limited to below are not covered by warranty:
(1) Power cord, filters or any other components considered as a “consumable parts” by
XPOWER.
(2) Normal wear and tear.
(3) Problems that result, directly or indirectly, at XPOWER’s sole discretion, from:
(3.1) External causes such as accident, abuse, misuse or problems with electrical power
supply.
(3.2) Disassembling, servicing or modification not authorized by XPOWER.
(3.3) Usage that is not accordant with product instructions stated in Owner’s Manual.
(3.4) Failure to follow the product instructions or lack of necessary maintenance stated
in Owner’s Manual.
Before contacting XPOWER, please try one or more of the following:
(1) Consult this Owner’s Manual and follow the instructions of troubleshooting guide.
(2) Access www.xpower.com for more advice and information that could be helpful to
address your problems.
If you need additional assistance from XPOWER, please:
(1) Email [e-mail].
(2) Call XPOWER U.S. Customer Service Department at 855-855-8868 or other numbers
provided on www.xpower.com.
(3) Visit XPOWER U.S. Head Office at 668 S. 6th Ave., City of Industry, CA 91746 or the
most current address provided on www.xpower.com.
Please also have your original proof of purchase and the serial number(s) of your
product(s) ready when you contact XPOWER.
IMPORTANT:
(1) Please finish the online warranty registration before usage. Visit www.xpower.com/
service-support/warranty-registration.
(2) This Limited Warranty applies with its own timeliness. Contact XPOWER or visit
www.xpower.com for more information.
!

English - 19
XPOWER Limited Warranty (USA)
If you are instructed to return the unit for service or replacement, please:
(1) Request a RMA (Return-Merchandise-Authorization) number.
(2) Use the original or an equivalent packaging, prepay shipping charges at your own
expense to the address provided by XPOWER, with the RMA number on the shipping
label or the packaging.
(3) Include all the original parts and components.
XPOWER will inspect, assess and advise the repairs needed and applicable cost, if any.
For products under warranty, we will pay to ship the repaired or replaced product(s) to
you if you use an address within the Contiguous United States. Otherwise, we will ship
the product(s) to you at your own expense.
(Continued)

Español - 2
Instrucciones de seguridad
ADVERTENCIA: LEA Y GUARDE ESTE MANUAL ANTES DE USAR ESTE PRODUCTO.
El usuario de productos eléctricos puede crear peligros que incluyen, pero no se limitan a,
lesiones, incendios, descargas eléctricas. El incumplimiento de estas instrucciones puede dañar
y/o perjudicar su funcionamiento y anular la garantía.
• Antes de operar, retire todo el material de embalaje y compruebe si hay algún daño que pudiera
haber ocurrido durante el envío o cualquier artículo faltante.
• Revise la fuente de alimentación de su hogar para asegurarse de que coincide con las
especificaciones del aparato.
• NO utilice el aparato con un cable o enchufe dañado. Deseche el aparato o devuélvalo a un
centro de servicio autorizado para su examen y/o reparación.
• NO use un cable de extensión con este aparato. Utilícelo únicamente en los tomacorrientes
protegidos con interruptor de circuito de falla a tierra (GFCI). Póngase en contacto con un
electricista calificado para la verificación y / o la instalación de un receptáculo GFCI si es
necesario.
• NO coloque el cable debajo de la alfombra. NO cubra el cable con alfombras, corredores o
revestimientos similares. NO en rute el cable debajo de muebles o aparatos. Coloque el cable
alejado del área de tránsito o de paso y donde no se vaya a tropezar.
• Para reducir el riesgo de incendio o descarga eléctrica, NO utilice este aparato con ningún
aparato de control de velocidad de estado sólido.
• NO toque este aparato ni el enchufe con las manos mojadas o mientras esté parado en agua.
• NO utilice el aparato en agua estancada.
• NO utilice el producto en áreas donde se utilice o almacene gasolina, pintura u otros bienes y
objetos inflamables.
• NO inserte ni permita que objetos entren en ninguna abertura de ventilación o escape, ya que
podría dañar el aparato y anular la garantía.
• NO cubra la entrada o salida de aire del aparato.
• NO dirija el flujo de aire al rostro o cuerpo de personas.
• NO permita que los niños jueguen con este aparato.
• APARATO DE FUNCIONAMIENTO AUTOMÁTICO – Para reducir el riesgo de lesiones,
desconecte la fuente de alimentación antes de realizar el mantenimiento.
• Retire el cable de alimentación del tomacorriente eléctrico agarrando y tirando solamente del
extremo del enchufe del cable de alimentación, NO tire del cable directamente.
• NO intente reparar o ajustar cualquier función eléctrica o mecánica de este aparato, ya que esto
puede resultar peligroso y anular la garantía.
• Si el aparato está dañado o funciona mal, NO continúe su uso. Desconecte el producto de la
toma eléctrica. Consulte la guía de solución de problemas o póngase en contacto con XPOWER.
• Cuando el aparato no se encuentre en uso, almacénelo en un área seca, lejos de la exposición a
la luz solar, temperatura extrema y humedad, así como de otros ambientes extremos.
• NO apile más de tres unidades de este aparato.
• Sujetar siempre la manija del carro y mantener la unidad elevada cuando la transporte de una
habitación a otra. NO ponga el producto de costado o boca abajo.
• Si el deshumidificador se transportó puesto de lado o boca abajo, debe ponerlo en posición
vertical y esperar al menos 4 horas antes de volver a utilizarlo.
• Se puede obtener un manual de instrucciones electrónico a través del sitio web del fabricante
www.xpower.com.
!