XPower GEN1.5 User manual

Wireless Remote-Control Instructions GEN1.5
X-Power wireless remote works lets you operate your winch from up to 75 ft without cables
or switches. Just press the remote transmitter and you're ready to operate your winch Start,
stop, in or out.
◆Remote range up to 75 ft.
◆Transmitter equipped with long life.
◆Battery and power saver circuit.
◆Transmitter & receiver.
◆Visual indicator light shows remote operation.
◆Additional transmitters available to operate receiver.
◆Installs in minutes.
◆Transmitter replacement battery readily available.
WARNING: The Wireless Remote is designed for use on front mount self-recovery winches
only. The remote is not designed for and should not be used on winches or hoists in industrial
applications (commercial car haulers/carriers, wreckers, cranes, etc.) or for any other remote
controlled applications.
Type:
RWRC①－②－③－④－⑤
①：Signed as 01, 02. ”01”: Code learning Type; “02”: Code Fixed.
②：Using Range admitted. Signed as E, C.”E” : European Using Style;
”C” Common style, this letter is always leave out;
③：Power Voltage, Signed as 12VDC or 24VDC.
④：Connector Style, using solely out of the winches control box. Signed as 03, 04. “03” :
three cores connector;
“04” : four cores of connector.
⑤: mount type, Signed as 05.
“05” :small remote can fix in the winches control box.
Part List:
1. one transmitter.
2. one receiver with three or four cores of line with connector.
Installation and operating instructions:
There are two kinds of different connect way for the reason of different kinds winches’ solenoid
female connector. You can choice a suitable type of wireless remote control as RWRC－03
or RWRC－04. showing as the following connection drawing.
RWRC－03: While you insert the receiver plug to the winches’ solenoid female connector, you
shold connect the earth line to the battery negative. Be sure of the earth line connect exactly,
then you can operate your winch by press the button on the transmitter.
RWRC－04: While you are ready to operate a winch, just connect the four cores of the recever
to the winches’ solenoid female connector. And then you can operate your winch by press the
button on the transmitter. NOTE: Make sure one of the four pole receptacle is connected to

earth.
“03”,”04”connection drawing:
Receiver
Transmitter
female connector
solenoid control box
There is a small remote can be fixed in the winches control box:
RWRC－05: While your fixing according to the drawings showing as follows:
We suggest operate your winch as follows:
1. Disengage the clutch of your winch.
2. Pull out the winch wire rope about 1.5 meters.

3. Reengage the clutch of your winch.
4. Insert the plug of remote control receiver into the winches’ solenoid control box
female connector, if your wireless remote control is －03 type, you should properly
connect the black earth line to the battery negative.
5. Put your receiver at a certain place.
6. Keep the antenna of receiver out and straight.
7. Pull out the antenna of transmitter, and move down the cover of your transmitter,
bare out the control button.
8. Press the button, you can operate your winch start, stop, in and out.
Trouble Shooting:
SYMPTOM
POSSIBLE CAUSE
SUGGESTED ACTION
Motor turns,
but Winch
does not work,
Defective winch.
Check the winch Operating instructions.
Motor does not
turn, but you
can hear “Click”
sound in the
receiver
Receiver Loose connections to
the winch.
Reinsert all the way.
False Earth line cinnection
Ensure the earth connections.
Defective winch.
Check the winch Operating instructions.
Motor runs in
one direction
Receiver Loose connections to
the winch.
Reinsert all the way.
only
Defective winch.
Check the winch Operating instructions.
No actions
Receiver and transmitter does
not matching.
“01” Type : Code learn.
“02” Type : return to the manufacture to
rematch.