Xpresskit DBALL User manual

Index
Installation Guide
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
SmartStart Compatible
SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Range
Extender Ready (RXT) mode without the use of a remote starter. See the Module Programming section for more
information.
© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Vehicle Application Guide................................................................................................................................................
Installation
Installation (Wiring Diagram & Vehicle Wiring Reference Chart).....................................................................................
SmartStart/XL202 Installation Notes...............................................................................................................................
Programming
Module Programming......................................................................................................................................................
Module Reset & Hard Reset............................................................................................................................................
Feature & Option List.......................................................................................................................................................
Feature Programming......................................................................................................................................................
LED Diagnostics & Troubleshooting................................................................................................................................
Limited One-Year Consumer Warranty............................................................................................................................
Quick Reference Guide...................................................................................................................................................
02
03
05
06
07
08
08
09
12
13
® Ford and Lincoln are registered trademarks and property of their respective companies.
This guide supports the installation of a DBALL in Range Extender Ready (RXT) mode. This solution
offers two (2) configuration options to control your system: Optional RF Kits or SmartStart (both sold
separately).
Important!
This product is ONLY compatible with vehicles equipped with a factory-installed remote starter.
Range Extender Ready (RXT) is used to dramatically increase the factory remote start activation range
compared to the factory transmitter. Refer to the Quick Reference Guide for more information.

© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Vehicle Application Guide
This installation type can be used in Push-to-Start (PTS) vehicles .ONLY
Page 2
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for
more information on installation wiring, programming and troubleshooting for these vehicles.
Vehicles
2016 2015 2014 2013 2012 2011 DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Trunk / Hatch Release PK-Push To Start Ignition Compatible RS-OEM Remote Start Activation using XL-202 or RF kit RS-SmartStart
Ford
Edge (Smart Key) • • • • • • • • • • • •
Expedition (Smart Key) • • • • • • • • • •
Explorer (Smart Key) • • • • • • • • • • • • •
Flex (Smart Key) • • • • • • • • • • •
Taurus (Smart Key) • • • • • • • • • • •
Lincoln
MKS (Smart Key) • • • • • • • • •
MKT (Smart Key) • • • • • • • • • • •
MKX (Smart Key) • • • • • • • • • • • • •
Navigator (Smart Key) • • • • • • • • • •
Legend
DL: OE Door Lock & Alarm Controls
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls

© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Page 3
Wiring Diagram
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
OBDII
Diagnostic Connector
1 8
169
10
DBALL/
DBALL2
RF
Prog.Button
LED
4
14 12 2
MS CAN High: Tan/Black: 3
MS CAN Low: Tan: 4
(-) Push-to-Start Output: Green/Black: 2
(-) Ground: Black: 14
(+) 12V: Red: 13
MS CAN High:
Gray/Orange,
pin 3 (-) Ground: pin 4
MS CAN Low:
Violet/Orange,
pin 11
(+) 12V:
Red/Violet,
pin 16
Start/Stop Switch
C2195 Connector
1
54
2
6
3
(-) PTS: Yellow or
Yellow/Orange, pin 6 6: White/Black: (-) Hood
Hood Pin
Remote Start Safety
Override Switch
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
Refer to the Wiring
Reference Chart
below for wire color
and pin number.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Page 4
Function Color Pin Polarity Location Color Pins
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/Gray 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/White 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/Blue 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/White 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/Blue 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/Blue 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/White 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/Gray 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
MS CAN High Gray/Orange 3 Data OBDII diagnostic connector. Black 16
MS CAN Low Violet/Orange 11 Data OBDII diagnostic connector. Black 16
12V Red/Violet 16 (+) OBDII diagnostic connector. Black 16
Ground Black/White 4 (-) OBDII diagnostic connector. Black 16
PTS Yellow or Yellow/Orange 18 (-) C2195 Connector start/stop switch. Black 6
Lincoln Navigator (Smart Key) 2015-2016
Ford Expedition (Smart Key) 2015-2016
Lincoln MKS (Smart Key) 2013-2014
Lincoln MKT (Smart Key) 2013-2015
Lincoln MKX (Smart Key) 2011-2015
Ford Taurus (Smart Key) 2013-2015
Wire Information Connector Information
Ford Edge (Smart Key) 2011-2014
Ford Explorer (Smart Key) 2011-2015
Ford Flex (Smart Key) 2014-2016
Vehicle Wiring Reference Chart

Page 5
© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
SmartStart/XL202 Installation Notes
The DBALL Range Extender Ready (RXT) solution offers two (2) configuration options to control your system: RF Kit or
SmartStart (both sold separately). This section provides specific installation information for SmartStart and XL202.
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
Antenna
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins,
not used
CABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.
2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
DBALL/
DBALL2
DBALL/
DBALL2
DBALL/
DBALL2
LED
Prog.
Button
D2D (4 pins, white)
4 pins
2 pins,
not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)
Cut Brown or Blue Loop
LED
THIS SIDE UP
LED

© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Flashes
Press 5 times on the programming button.
The LED flashes orange. &
Press x5
Module Programming Page 6
2Make sure the key is inside the vehicle.
Key Inside
the Vehicle
4
&Press x2
ENGINE
START
STOP
Do NOT
press the
brake pedal
Press the Push-to-Start (PTS) button twice to turn the ignition ON.
Important: Do NOT depress the brake pedal.
3
Go to the next page to complete the module programming.
Refer to the LED Diagnostics section on page 9 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit
available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware
that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Config for RXT, and follow the instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.
6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”
You can now proceed with the programming instructions below.
1
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
&
Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to
DBALL, then wait until the LED turns ON solid red.
10-pin
D2D
XL202
10-pin
D2D
SmartStart
OR
The DBALL module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL.
a. To ensure that the D2D communication between SmartStart and DBALL works properly, the
Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue
loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
SmartStart Installation
Connect XL202 to DBALL using the D2D port.
XL202 Installation

© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Page 7
Module Reset
1If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
2
Solid
&
Release
3 Release the programming button. The LED turns ON solid red.
Hard Reset
2& &
1
Wait 3 seconds until the LED turns ON solid orange then release the
programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
Solid Release Solid
Solid Flashes
&
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds
until the LED starts to flash orange and red.
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
Press the PTS button once more, to turn the
ignition OFF.
Press x1
ENGINE
START
STOP
5
The LED will flash green, then turn on solid orange
for 3 seconds and turns OFF once the module has
been successfully programmed. &&
Solid
x3 secs
Flashes Off
&

© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Page 8
Feature and Option List
To enter feature programming routine
-Turn the ignition ON, then OFF.
-Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.
-The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat
until a new command is entered.
Changing feature options
-Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
-The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly
the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature
-Press and release the programming button a number of times to advance from the current feature to the next desired feature.
-The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed
-Other features can be programmed.
-The feature programming can be exited.
Exiting feature programming
-No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.
OR
-Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the
end of the programming sequence.
Feature Programming Programming
Button
* Default option
Feature
Operation Flashes / Option Description
1. Disabled* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Disabled
The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm
command will be executed at the beginning or end of the sequence; it must be controlled by
the Remote Starter.
2. Safelock Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It
will unlock at the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and
rearm the vehicle in the remote start sequence, only when required. The reason for this is,
factory alarm control must often be done by lock or unlock operation. This could create
unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart
OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or
rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote
starter actions so that the factory alarm control is not done twice. A remote starter, for which
the Safelock feature is active, will work perfectly with this option and will make it invisible to
the user.
2 Smart OEM Alarm Control
1 RF Output Type
It is recommended to configure all the features and options listed below using the configuration tool found on the module
flashing page on www.directechs.com. The web offers more options such as RXT; however, manual configuration of the
features is possible using the information on this page.

LED Diagnostics & Troubleshooting
© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
Page 9
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence. Ensure the correct programming procedure is being
followed.
Initialization failed. Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated. Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions. Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected. Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes red
x 1
Flashes red
x 1
Flashes red
x 2
Flashes red
x 3
Flashes red
x 4
Flashes red
x 5
Flashes red
x 6
Flashes red
x 7
Solid green
x 3 secs
Flashes
green
Solid orange
Flashes red
& green
Off
Flashes
orange
Flashes
orange
slowly
Solid orange
x 3 secs

© 2016 Directed. All rights reserved.
Rev.: 20160810
Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation
LED Description Troubleshooting
OBDII feature is not supported. The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received. The module has received the Ignition ON command and is
processing the remote start sequence.
Start ON command received. The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error. The PTS output from the module was not activated due to
safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to “Installation
(wiring diagrams & vehicle wiring reference charts)” to check
the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled. No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected. The brakes were not detected, which prevents the system
from shutting down the vehicle.
Smart key was not detected. The smart key was not detected, which prevents the system
from shutting down the vehicle.
Speed was detected. The vehicle was detected as moving, which prevents the
system from shutting it down.
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,
red then
orange) x 10
Flashes red
& orange
Flashes red
x 21
Flashes red
x 2
Flashes red
x 4
Flashes red
x 10
Flashes red
x 1
Flashes red
x 3
Flashes
green
Flashes
green
quickly
Flashes
green x 1
Flashes
orange x 1
Flashes
orange x 2
Flashes
orange x 3
Flashes
orange x 5
Flashes
orange x 4
Flashes
orange x 6
Page 10