XtendLan XL-FLS1315 User manual

XL-FLS1315
USER'S GUIDE
Optical Laser Source

¨
WARNING
You are cautioned that changes or modifications not espressly approved in this document
could void yout authority to operate this equipment.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
NOTE
As the laser is harmful to the eyes, do not attempt to disassemble the cabinet.
Precautions forUse
Use batteries
At the same time, can not use different style or different capacitance batteries. And only charge the rechargeable batteries.
Avoiding condensation problems
As much as possible, avoid sudden temperature changes. Do not attempt to use the drive immediately after moving it from a cold to a
warm location, to raising the room temperature suddenly, as condensation may form with in the drive. If the temperature changes
suddenly while using the drive, stop using it and take out batteries for at least an hour.
Storage
When long time no use, must take out the batteries to avoid destroying the device!
VISIBLE LASER RADIATION
AVOD EYE OR SKIN EXPOSURE
TO DIRECT OR SCATTERED RADIATION
SEMICONDUCTOR LASER
Wavelength:635-650nm
INVISIBLE LASER RADIATION
AVOD EYE OR SKIN EXPOSURE
TO DIRECT OR SCATTERED RADIATION
SEMICONDUCTOR LASER
Wavelength:800-1700nm
CLASS II LASER PRODUCT

Check the accessories
Standard Edition
Soft Bag

Description
1Laser Source Connector
2AC/DC Socket
3LCD
4Power Button
5Wavelength ID
6Output wavelength switch button
7 Load modulation

Installing the battery
1. Pull the battery cover 2.Installing the battery 3.Push the battery cover 4.Complete

On/Off and Permanent On
Press button to turn on the meter .
Press button again for two seconds or more to
turn off the meter.
This meter has power-saving function, if ten
minutes without any operation, the device will automatically shut down.
If you need to disable this function, only need to press the button
for 2 seconds when you turn on the meter till it displays 'PERM'.

Backlight Function
When the meter is power on , short press the
button, you can control the backlight
function on or off. The backlight function is used when you
want to use the meter at night or darker occasions.

Select Wavelength
Atter pressinq button, you can select
the required outp ut wavelengths. Details refer to
the parameters table.
The power meter or other measuring equipments
should select correspond wavelength of laser source.

Modulation output
After pressing button, you can load a
modulation current output laser.
This instrument has three modulation for selection:
270Hz, 1 kHz, 2 kHz.

Wavelength identification
Press Button. the laser source will output with
wavelength ID an d LCD will display ’Id'. and if works
with the paired power meter with WAVE ID function.
the optical power meter will change to the same
wavelength automatically.

Power Indicator
Four levels indicatio n of power detection
Represents the rema ining 8 0%---
J 00% electricity
Represents the rema ining 40%---80% electricity
Represents the rema ining 20%---40% electricity
Represents the rema ining electricity less tlnan 20%

Charge
The instrument has a charging function. When use
rechargeable batteries and a low battery indication
shows on the instrument, you should promptly shut
down it and recharge. Long time under voltage
will shorten the lifetime of the rechargeable battery.
Connect the AC adapter to the device correctly, it can
charge automatically. Besides, computer USB port can
also be used for charging. The battery remaining indicator
keeps flashing during charging. It will stop when the
charging is finished. The battery has finished the fast
recharge and can be used directly. If you do not stop
recharging at this time, the instrument will continue the
trickle charge state, using small current to supply natural
discharge. But this process is not more than 48 hours.
The instrument can still be used while charging. But do
not plug in the AC adapter when it isn’t rechargeable
battery inside, or it will cause a high temperature and
combustion, even explosion.

Detail parameters
Output length }nm]
1310 / 1550
Output power
> -6dBm
Laser type
Fabry-Perot Laser Diode
Optical adapter
FC/PC
Modulation wave
270Hz / 1kHz / 2kHz
Auto off
Yes
Battery type
2x AA
Battery lifetime
> 40 hours
Waterproof
Can prevent small splash
Size (h, w, d)mm
140 x 62 32
Weight
174g