Xtralis IntrusionTrace User manual

Xtralis
IntrusionTrace™
Quick Start Guide
September, 2012
Doc. 21808_01

Doc. 21808_01 i
IntrusionTrace Quick Start Guide
Disclaimer
The contents of this document is provided on an "as is" basis. No representation or warranty (either express or implied) is made as to the
completeness, accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or
specifications without obligation and without further notice. Except as otherwise provided, all warranties, express or implied, including
without limitation any implied warranties of merchantability and fitness for a particular purpose are expressly excluded.
Intellectual Property and Copyright
This document includes registered and unregistered trademarks. All trademarks displayed are the trademarks of their respective owners.
Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/or label. This
document is subject to copyright owned by Xtralis AG ("Xtralis"). You agree not to copy, communicate to the public, adapt, distribute,
transfer, sell, modify or publish any contents of this document without the express prior written consent of Xtralis.
General Warning
This product must only be installed, configured and used strictly in accordance with the General Terms and Conditions, User Manual and
product documents available from Xtralis. All proper health and safety precautions must be taken during the installation, commissioning
and maintenance of the product. The system should not be connected to a power source until all the components have been installed.
Proper safety precautions must be taken during tests and maintenance of the products when these are still connected to the power
source. Failure to do so or tampering with the electronics inside the products can result in an electric shock causing injury or death and
may cause equipment damage. Xtralis is not responsible and cannot be held accountable for any liability that may arise due to improper
use of the equipment and/or failure to take proper precautions. Only persons trained through an Xtralis accredited training course can
install, test and maintain the system.
Liability
You agree to install, configure and use the products strictly in accordance with the User Manual and product documents available from
Xtralis.
Xtralis is not liable to you or any other person for incidental, indirect, or consequential loss, expense or damages of any kind including
without limitation, loss of business, loss of profits or loss of data arising out of your use of the products. Without limiting this general
disclaimer the following specific warnings and disclaimers also apply:
Fitness for Purpose
You agree that you have been provided with a reasonable opportunity to appraise the products and have made your own independent
assessment of the fitness or suitability of the products for your purpose. You acknowledge that you have not relied on any oral or written
information, representation or advice given by or on behalf of Xtralis or its representatives.
Total Liability
To the fullest extent permitted by law that any limitation or exclusion cannot apply, the total liability of Xtralis in relation to the products is
limited to:
(i) in the case of services, the cost of having the services supplied again; or
(ii) in the case of goods, the lowest cost of replacing the goods, acquiring equivalent goods or having the goods repaired.
Indemnification
You agree to fully indemnify and hold Xtralis harmless for any claim, cost, demand or damage (including legal costs on a full indemnity
basis) incurred or which may be incurred arising from your use of the products.
Miscellaneous
If any provision outlined above is found to be invalid or unenforceable by a court of law, such invalidity or unenforceability will not affect
the remainder which will continue in full force and effect. All rights not expressly granted are reserved.
Document Conventions
The following typographic conventions are used in this document.
Convention Description
Bold Used to denote: emphasis
Used for names of menus, menu options, toolbar buttons
Italics Used to denote: references to other parts of this document or other documents. Used for the result of an
action
The following icons conventions are used in this document.
Convention Description
Caution: This icon is used to indicate that there is a danger to equipment. The danger could be loss of data,
physical damage, or permanent corruption of configuration details.
Warning: This icon is used to indicate that there is a danger of electric shock. This may lead to death or
permanent injury.
Warning: This icon is used to indicate that there is a danger of inhaling dangerous substances. This may
lead to death or permanent injury.

ii Doc. 21808_01
Quick Start Guide IntrusionTrace
Tradename statement
ADPRO is a registered trademark of Xtralis AG Pty Ltd.
Contact Us
The Americas [phone] Asia [phone] Australia and New Zealand [phone]
UK and Europe [phone] Middle East [phone]
www.xtralis.com

Doc. 21808_01
IntrusionTrace Quick Start Guide
Contents
1Introduction................................................................................................................................1
2Scope..........................................................................................................................................1
3Prerequisites..............................................................................................................................1
4Install IntrusionTrace ................................................................................................................2
4.1Redeem Credit Token......................................................................................................2
4.2Create License File..........................................................................................................3
4.3Install License on FastTrace 2 Unit................................................................................4
4.4Activate License on Video Channel ...............................................................................6

Doc. 21808_01 1
IntrusionTrace Quick Start Guide
1 Introduction
The ADPRO®FastTrace 2/2IntrusionTrace™ application is designed to provide full
outdoor perimeter detection analytics. It provides reliable and predictable detection of
intrusion into secure outdoor areas. The system analyses images from strategically-placed
cameras to detect “human-like‟movement, and if the movement fulfills a number of criteria,
alarms are generated. These alarms are handled by the FastTrace 2/2video system and
can be transmitted to a remote central monitoring station assessed and managed by
experienced security personnel.
A well designed, installed and maintained IntrusionTrace application can remove the need
for onsite guards or patrols, or provide assistance to local monitoring, thus, improving the
effectiveness of the overall site security.
2 Scope
This quick setup guide describes in direct steps how to install the IntrusionTrace Video
Perimeter Detection solution on an existing FastTrace 2 or 2system.
This guide is intended for users who are familiar with the key concepts of FastTrace 2/2
and the Xtralis application license portal. For detailed information on FastTrace 2/2, please
refer to the “Technical Installation Manual”. For more information on the concept of Xtralis
application license web portal and how to use it, please refer to “Xtralis Application License
guide” document.
Both of these documents can be found and downloaded through www.xtralissecurity.com.
Please note that the installation steps can be done locally on site or remotely. Make sure that
the appropriate connection to the internet and FastTrace 2/2unit are available.
3 Prerequisites
In order to install IntrusionTrace, the following prerequisites must be met:
A FastTrace 2 or 2device to install IntrusionTrace on. Note that FastTrace 2 supports
a maximum of 4 analytics channels and FastTrace 2X supports up to 16 analytics
channels. The FastTrace 2/2device needs to have at least a firmware version v2.6 or
higher.
Account on the Xtralis Application License Portal: license.xtralissecurity.com
If you do not have an account, please register through the login page. Your account
request will be validated by Xtralis and you will receive an email as soon as your
account has been approved.
IntrusionTrace Application licenses that have not been used yet and can be installed on
a FastTrace 2/2X device. You need to add a new IntrusionTrace Credit Token to your
account in case all of your licenses are already assigned to FastTrace 2/2unit(s).
Xtralis License Tool. This tool is used to install the license files downloaded from the
license portal on the FastTrace 2/2device(s). This tool can be downloaded from the
License Portal web page, it is also found on the CD that comes with your FastTrace
2/2unit.
Microsoft .NET 4 Framework needs to be installed on your PC. Note that it might already
be installed on your PC. If the installation of the Xtralis License Tool displays an error
message on start, then please download and execute/ install the file through:
http://www.microsoft.com/en-us/download/details.aspx?id=17718

2 Doc. 21808_01
Quick Start Guide IntrusionTrace
4 Install IntrusionTrace
The following sections discuss how you can redeem your credit token and create the license
file to eventually install and activate your IntrusionTrace application on FastTrace 2/2.
4.1 Redeem Credit Token
To redeem the credit token, follow these steps:
1. Go to http://license.xtralissecurity.com and login to your account. If you are a new
user, register for an account.
2. Click the menu item Redeem Token, the following page appears:
If you already have licenses available on your account that you wish to deploy on a
FastTrace 2 unit, then please jump to section 4.2.
However, if you want to redeem your credit token continue with these steps.
3. Enter the credit identifier available with your purchased credit token, it appears as
shown below:
4. Click (Redeem Token) button.
NOTE!
If a valid credit number has been entered, the web portal activates the
Licenses menu. Otherwise, a message appears to inform you of the
error.

Doc. 21808_01 3
IntrusionTrace Quick Start Guide
4.2 Create License File
Now you can activate one or more licenses from your existing license pool to a FastTrace 2
or FastTrace 2unit.
Click the Licenses menu item, the following page appears:
This menu is activated anytime you have redeemed a valid credit. Refer to section “4.1
Redeem Credit Token”.
You can create one or multiple licenses, to do so, follow these steps:
1. Click the checkbox next to the license that has not been added to any FastTrace 2 or
2device. You can select more than one at the same time.
2. Click (Create License), the following page appears:
3. Select the device for which you want to activate the licenses. The menu displays your
device name if it is already known by the portal, if it is not, enter a new device serial
number (MAC address of the FastTrace 2 or 2unit).
NOTE!
The MAC address contains letters that must be entered in capital
letters. When you enter a new serial number, also enter a device
description (such as project name, company name, site name, etc),
this helps you in more easily identifying the unit afterwards.

4 Doc. 21808_01
Quick Start Guide IntrusionTrace
4. Click (Create License). The web portal has now marked the selected licenses as “in
use”.
The system immediately provides you with a downloadable file which is used to deploy the
application to your FastTrace 2/2unit as discussed in the coming section.
4.3 Install License on FastTrace 2 Unit
To install the license on your FastTrace 2 unit, follow these steps:
1. Start the License Tool software,
2. Add the FastTrace 2 or 2unit to the device list, then click the image that represents
it, the following page appears:
The page shows information of the selected unit. Also note that the Licenses page is
activated and can be accessed.
3. Click (Licenses), the following page appears:

Doc. 21808_01 5
IntrusionTrace Quick Start Guide
The page is divided into three sections: the Installed which shows which licenses have
already been installed on the unit, the Available which shows license files available for
installation, and Synchronization Summary.
4. Drag and drop the license file you created to the Installed section, it appears in the
Available section as shown next:
The license file is now available for installation.
5. Click (Synchronize) to apply the changes to the FastTrace 2/2unit, the page
appears as shown below:
The application has been installed on your unit.

6 Doc. 21808_01
Quick Start Guide IntrusionTrace
4.4 Activate License on Video Channel
After you have successfully installed the IntrusionTrace application license on the FastTrace
2/2unit, you can now configure your analytics channel. To do so, follow these steps:
1. Assign the application license to the video channel you choose from the “Select
IntrusionTrace License” menu found in the right section of the below image:
2. Define the detection zone,
3. Calibrate the scene.
For more information on how to configure the IntrusionTrace settings, refer to the “FastTrace
2/2Technical Manual“.

IntrusionTrace Quick Start Guide
www.xtralis.com
The Americas [phone] Asia [phone] Australia and New Zealand [phone]
UK and Europe [phone] Middle East [phone]
The contents of this document are provided on an “as is” basis. No representation or warranty (either express or implied) is
made as to the completeness, accuracy or reliability of the contents of this document. The manufacturer reserves the right to
change designs or specifications without obligation and without further notice. Except as otherwise provided, all warranties,
express or implied, including without limitation any implied warranties of merchantability and fitness for a particular purpose are
expressly excluded.
This document includes registered and unregistered trademarks. All trademarks displayed are the trademarks of their
respective owners. Your use of this document does not constitute or create a licence or any other right to use the name and/or
trademark and/or label.
This document is subject to copyright owned by Xtralis AG (“Xtralis”). You agree not to copy, communicate to the public, adapt,
distribute, transfer, sell, modif
y
or
p
ublish an
y
contents of this document without the ex
p
ress
p
rior written consent of Xtralis.
Doc. 21808_01