Xtreme DX200 User manual

Instruction and Assembly Manual
Version 1.0 (Jan 2017)

Tools Needed (Not Included) :
Equipment required :
Radio System Speed control
Receiver Video TX Transmission antenna
Screw Driver 1.5mm Allen wrench 2mm Allen wrench
Features:
•Weight of frame is 65 gram only.
•USA made Light weight 3.5mm 3K Carbon Fiber airframe
plate.
•Compact size for 5" propellers, 200 mm motor to motor.
•Titanium M3 Screws included.
•Multiple Arms Forward Attacking Angle adjustable
(0, 5, 10, 15 degree tilt foward) to maximize forward speed.
Cam Battey
Flight control board Power distribution
board
Motor 2204~2206
(Shaft size is 5mm)
X4 X4
Thank you for purchasing the Xtreme production DX200 . It is a competition racing drone and it is
required some knowledge of FPV model building. please read this manual in detail before you
start building this drone.

Before you start, please understand the usage of
different sets of screw holes on the side carbon panel:
Yellow:
For front arms to adjust forward
attacking angle
Yellow:
For rear arms to adjust forward
attacking angle
Red:
For Main electronic
mount deck.
Green:
For the upper deck
Pink:
space for Receiver antenna
Blue:
For Camera mount White:
Holes or fixing wires.
P.1

Battery strap
Alu.brace
Main electronic mount deck
M3X6 screws
Power distribution board
or
4 IN 1 Speed Control
(Not Included)
M3X8 screws
(Plastic)
hole to hole size is 20mm to 30.5mm
20mm
30.5mm
3mm washer
(Plastic)
M3x8 Hexagonal column
(Plastic)
P.2

D
A
BC
Installationin:
A = 0 Degree
B = 5 Degree
C =10 Degree
D =15 Degree
D
A
B
C
Installationin:
A = 0 Degree
B = 5 Degree
C =10 Degree
D =15 Degree
Front Arms Mount
Rear Arms Mount
Main frame
(side carbon panel)
M3X6 screws
M3X6 screws
M3X6 screws
P.3

P.4
M3X6 screws
Motor screws
(Not Included)
Motor screws
(Not Included)
Motor (Shaft size is 5mm )
2204/2205/2206/2207
(Not Included)

P.5
Motor (Shaft size is 5mm )
2204/2205/2206/2207
(Not Included)
Motor screws
(Not Included)
Motor screws
(Not Included)
M3X6 screws

P.6
Flight control board
(Not Included)
Speed control
(Not Included)
Speed control
(Not Included)
Speed control
(Not Included)
M3 nut
(Plastic)
Double Sticker
Double Sticker

P.7
Camera
(Not Included)
12/15/16mm
cam mount
M2X12 screws
M2 nut
cam mount brace
M3X6 screws
M3X6 screws
Main frame
(side carbon panel)
M3X6 screws
hole for adjustable
camera Angle
hole for run cam
Swift 2 / Swift / Owl Plus

P.8
Rx and Vtx installation
Method 1:
Rx and Vtx installation
Method 2:
Double Sticker
Need
Conversion wire
(Not Included)
M3X6 screws
Alu.brace Alu.brace
Double Sticker
Receiver
(Not Included)
M3X6 screws
Video TX
(Not Included)
Transmission antenna
(Not Included)
upper deck
Transmission antenna
(Not Included)
Receiver
(Not Included)
Double Sticker
M3X6 screws
M3X6 screws
upper deck
Alu.brace
Video TX
(Not Included)
Video TX Mount

M3X6 screws
M3X6 screws
Rx and Vtx installation
Method 2:
M3X6 screws
M3X6 screws
P.9
Method 1 Installation is hole
Method 2 Installation is hole
Rx and Vtx installation
Method 1:

P.10
Battery strap
Battery
(Not Included)
Sponge Sticker
Sponge side
Sticker side

P.11
Make sure Motor and propeller spin direction is correct
As indicated below
propeller
Motor Nut
(Not Included)
Motor 2
(Base setting)
Motor 4
(Base setting)
Motor 3
(Base setting)
Motor 1
(Base setting)

End of Assembly