XtremepowerUS 75136 Original instruction manual

A-FRAME ABOVE GROUND POOL LADDER
ITEM# 75136
'
)
OWNER'S MANUAL AND SAFETY INSTRUCTIONS
 
 
  

 

1

1. Remove the A-Frame ladder and its accessories from the box and check whether all
the accessories are complete.
2. First place the boom tread on a flat surface with the grooved side facing up; then
snap the two holders into the groove. Note: The two holders need to be snapped into
the groove in the same direction.
Tighten with screws for both
right and lift sides
Holder
SSecure with a screw
3. Install four treads to the holder, see the picture as below. Affix the top tread
to the holder by #10x1-1/4 screws.
2

6. Put another bottom tread on a flat surface with the grooved side facing up. Then
snap the two holders into the groove. Note: The two holders need to be snapped into
the groove in the same direction.
bolt
Gasket
Nut
Fix the treads to the left and
right fixing strips with screws.
Left fixing strip
Tighten with two screws for both sides
Holder
Right fixing strip
5. Use the 10x1-1/4 screws to affix the other three treads. Then put aside for later.
4. AAffix the left and right fixing strips with bolt & gasket ( M6), and nut M6*85,
donot over tighten (the accessories are in screw kit 5862050002 )
3

7. Affix the treads to the holders with screws with #10x1-1 / 4 .
8. Place the Lower Base on a level surface. Snap the front barrier into the
groove on the lower base facing round edge. Snap the back barrier into the
groove on the lower base facing the straight side.
9. Slide the upper brace over the front barrier as shown. Slide the upper brace
through the groove in the Back Barrier and push down lightly to secure.
Lower base
Fix the tread to holder with
screws
Front barrier
Back barrier
Upper brace
Slide upper brace through the
groove
4

10. Fix lower base of entrapment barrier into bottom step of the Inside portion of
the Ladder with 2 pieces10 x 1-1/4# screws.
11. Fix the remaining two treads with 10x1-1/4 screws to the holder in the groove
positions
Install the treads with screws
Fix the barrier on to these two
posions
10. Affix the lower base of the entrapment barrier into bottom step of the Inside
portion of the Ladder with 2 pieces10 x 1-1/4# screws.
11. Affix the remaining two treads with 10 x 1-1/4 screws to the holder in
the groove positions
Install the treads with screws
5
Affix the barrier onto
these two positions.

52"Cut line
48"Cut line
48"cut line for holder
12. The ladder is designed to fit multiple pool heights. If your pool height is 52", locate
the first line on the handrail of the ladder. Using a hacksaw, cut the handrail evenly
through both sides.
If the pool height is 48", locate the second line on the handrail. Using a hacksaw, cut the
handrail evenly through both sides. Locate the line on the holder and cut the
redundancies evenly through both sides.
If your pool height is 54" there is no need to cut it.
6

13. Using a funnel, fill both holders with sand. Use approximately 20 Lbs. of sand in
each holder. The barrier in step 11 have the front and back barrier.
15. Attach handrails by pushing them down over the holders.
Fill holder with sand using a funnel
Cover Cap Deck Plate form
Handrail
14. Assemble the handrails to the platform. Center the cover cap opening on
the side of the handrail when the platform was just attached. Using a rubber
mallet/hammer, tap on the cap until the cap is flush with the handrail.
7

16. Secure all handrails to the legs with #10 1-1/4# screws
Place the ladder inside the pool where you want to enter and exit. The entrapment
barrier should be inside of the pool. Once the ladder is placed in the pool, tip the
ladder forwards and backwards and side to side to release any air that may be
trapped inside.
Pushing them
down over the
holders
Step 15 Step 16
Screw
The swing up outer tread is at
the outside of pool
Place weighted sandbags and/or
sand-filled containers on the base of
the steps to secure it in place. Sold
separately.
8

The A-Frame ladder must be fixed on the edge of the pool. First, align the two holes
on the surface of the deck platform with the edge of the pool, mark the hole
positions at the edge of the pool with a fine marker pen, then drill through the edge
of the swimming pool with a 5 / 16 "drill bit, and finally use bolts, nuts and washers to
fix the ladder on the edge of the swimming pool.
Routine Maintenance
When the swimming pool is not in use, it is recommended to flip the outer ladder
upwards, then push it down and fix it.
Deck Platform
Pool Edge
Bolt
9
If your pool height is 48", use the 2.5 bolt 5862050000 screw kit.
If your pool height is 52", use the 5 bolt 58620500001 screw kit.
If your pool height is 54", use the 5 bolt 5862050001 screw kit.
2. When removing the ladder, it is recommended to wash the ladder with soapy
water to remove and debris.
1. In cold weather and/or wintertime, remove the ladder and store it in a clean, dry
place.