XTS Video XTS-KBC-100 User manual

Multi-Protocol controller
keyboard
XTS-KBC-100
USER‘S MANUAL

Warning
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION
GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.
FCC COMPLIANCE STATEMENT
FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE
DESIGHEND TO PROVIDE REASONABLE PROTECTION AGAINST HAMRFUL INTERFERENCE WHEN THE
EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES,
AND CAN RADIATE RADIO FREQUENCY ENGERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE
WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE
INTERFERENCE AT HIS OWN EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE COULD VOID THE USERS‘S AUTHORITY TO OPERATE THE EQUIPMENT.
CE COMPLIANCE STATEMENT
WARNING: THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE
RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE
MEASURES.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present within
this unit.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER ( OR BACK). NO
USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
1

Contents
Warning............................................................................................... 1
Contents.............................................................................................. 2
Introduction..........................................................................................3
Installation........................................................................................... 4
Stand-Alone mode...............................................................................5
RS-485 network...................................................................................6
Working with the keyboard.................................................................. 7
Operating.............................................................................................8
PTZ-operation......................................................................................9
Cruising functions................................................................................10
Sequence setup...................................................................................11
Viewing control.................................................................................... 12
Keyboard setup menu..........................................................................13
Keyboard Setup / Auxiliary Functions..................................................14
Key- Function Overview.......................................................................15
Specification........................................................................................ 16
2

INTRODUCTION
•3-Axis controlling stick provides max. usability and performance( Pan/ Tilt / Zoom) in 1-hand-
operation.
•Variable, step-less controlling speed for PTZ, easy for manual object tracking.
•Large-sized, high-contrast LCD display with green back-light for a comfortable overview and
detailed status report.
•Easy access: Hot-keys for most frequently used PTZ function.
•Programming and call of presets, tour and pan-swing.
•Direct parameter setup for accessing additional camera / speed-dome functions ( e.g. Flip
images, switching day/night mode..etc).
•Controls up to 255 Speed-Domes or PTZ Devices from 1 keyboard.
•Master / Slave operating mode for multiple control ( 2 modes).
•Built-In configuration menu for keyboard setup.
•Double-featured keypad inputs ( by pressed longer than 3 sec.)
Features
3
The keyboard Intelligent, multiple-protocol keyboard controller is designed for operator to control
speed-domes, zoom camera and PTZ device. it‘s ergonomic concept and user-friendly 3-axis
controlling stick provide its operator max. usability and performance. With this keyboard
controller, you can also easily activate and programming presets, tours and memorized personal
references on PTZ devices. It can also be used to access addtional devices setting via short key,
such as manual / auto iris, day&night mode changing and etc.
The large-sized LCD is used to display current status, and as well as to provide a menu-system
for setting operational parameter of the keyboard. It is equipment with a green back-light for
operation under different conditions.
This keyboard contains 2 RS-485 connectors for operation in Master- or Slave-mode, which can
be used in multiple-control environment with selectable privilege.
•Multiple-Protocol support in each channel.(XTS, XTS-2, B01, Pelco D, Pelco P).

INSTALLATION
Unpacking
Please unpack the equipment and make sure all listed items and accessoriesareincluded in the box:
Keyboard controller 1
RJ-11 RS485 connection cable 1
Instruction manual 1
There are 2 RJ-11 connectors on the keyboard for RS-485 control:
RS485-1( Master port) line connector is normally used forSpeed-Dome or other PTZ-device withRS-
For further information regarding wiring, please refer tothe operation manual ofthe connected PTZ
devices.
Keyboard ID
Some PTZ devices might require the setup ofkeyboard’s ID ( sender ID), you can set theIDby
Connection
ID is 0
( default setting)
ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8
ID is 1 ID is 2 ID is 3
9 ~12V Power supply
500mA
Master port Slave port
R RS485+
Bl RS485-
CGND
Y GND
RJ11 cable
Speed dome /
PTZ devices
4
Chunk box
1
Chunk box
485 connector. Indicator for chunk box wiring: Red:RS485+, Black: RS485 -,Green & Yellow: Ground.
changing the DIP-switch of no.1 and 2 on the back pane l of the keyboard.The default settingis“0”

STAND-ALONE
Stand-Alone / Master-Slave operation
This keyboard support 2 operation mode for max. 255 devices connected. Depends on the
requirement, you can setup the keyboard for stand-alone or master/ Slave mode:
1. Stand-Alone mode:
Only 1 controller keyboard is used for all connected devices. In this operation mode, both
connectors ( RS-485-1 and RS-485-2) can be used. Depends on the wiring type, you might need to
active the termination of the keyboard for the RS-485 chain. The connection
Setup the Stand-Alone mode:
ON 1 2 3 4 5 6 7 8
2. Depends on the wiring, you might need to activate the on-board
termination of the keyboard for RS-485 connection chain. Use DIP-
switch no. 7 (port RS-485-1) and no. 8 (port RS-485-2) for enable or
disable the on-board termination.
1. On the back panel, set the DIP-Switch no. 3 and no. 4 to state „OFF“
SettingSteps:
ON
3 4
ON
7 8
RS-485 Chain no.1 RS-485 Chain no.2
Up to
32 devices ....
...
Termination
5

MASTER/SLAVE MODE
(optional function)
2. Master / Slave mode:
For certain installations, multiple-control structure might be required. You can setup the keyboard to
Master / Slave mode in order to work with more than 1 keyboard simultanously. In this operation
mode, all keyboards have to be connected in a chain, with RS-485-1 for output and RS-485-2 as
input ports. The keyboard that is nearst to the devices has the highest priority.
How to setup Mater/Slave mode:
Keyboard 1 Keyboard 2
Other keyboard
or termination
To PTZ or speed
dome devices
Up to
32 devices ...
ON 1 2 3 4 5 6 7 8
2. Depends on the wiring, you might need to activate the on-board
termination of the keyboard for RS-485 connection chain. Use DIP-
switch no. 7 (port RS-485-1) and no. 8 (port RS-485-2) for enable or
disable the on-board termination.
1. On the back panel, set the DIP-Switch no. 3 to state „OFF and no. 4
to state „ON“
SettingSteps:
ON
3 4
ON
7 8
6

RS-485 NETWORK
Multiple connections to a single port
Depends on the installation environment, you may have different RS-485 chains connected as a
„network“. In order to let your keyboard working properly, please refer to the examples given
bellow:
You can connect max. 3 RS485-chains to each port ( in Master / Slave mode: connect only to RS-
485-1 port.) For more chains, you need to use a RS-485-Distributor to expand the connectivity
( Please contact technical personnel or sales representatives for purchasing and further
information). The total number of connected devices shall not exceed 32.
* Depends on cable-quality and environment, the wiring length might be shorter than specified.
4-way RS-485
Distributor
RS-485 chain no.1, up to 1000 m*
RS-485
Distributor
Max32 devices
Star- / Tree- Connection network
Basically, a star connection is similar to a
multiple-connection. Each RS-485 port on the
keyboard can handle up to 3 chains ( totally 6
chains in stand-alone mode, Only 3 chains in
Master/ Slave operation mode). In case more
chains are present, you might need to use RS-
485 distributors. Each chain can be expanded
with RS-485 distributor ( tree-connection). The
total number of connected PTZ devices shall
not be more than 32.
RS-485-chain no. 3
up to 1000 m*
RS-485-chain no. 4
up to 1000 m* Further RS-485-chains through
2nd RS-485 distributor,
with each chain length up to 1000 m*
RS-485
Distributor
RS-485
Distributor
RS-485 chains
7
RS-485
Distributor
OR

WORKING WITH KEYBOARD
Front panel
1
2
3
45
6
1. Status & Menu Display: LC-Display with back-light shows current keyboard setting, status and
configuration menu.
2. Extended Function keys: activate extended functions, such as extended camera settings and setup
3. Operation keys: Performing default operations such as presets, sequence, camera selection etc.
4. Digit pad: Numeric input for parameter setup.
5. Camera operation keys: Manual iris and focus control, secondary zoom-control button.
6. 3-axis PTZ-stick (KB3A only) for pan, tilt and zoom: PTZ control.
8
Note:
- the default operation keys can provide a secondary function by keep on pressing longer then 3 seconds.
Please refer to the chapters for detailed description
- Combined with the operation keys, you might need the digit pad for parameter input. Press [ENTER] for
input confirmation and [CLEAR] for cancellation.

OPERATING
Turning on the keyboard
This keyboard can control up to 255 connected devices. You can select any one by pressing
[CAM] + [ID]+ [ENTER]
9
VERSION V2.06 LCD shows the keyboard‘s firmware version
and manufacturing date
After plugging in the power, the keyboard will start the initialization and self-test. The LC-Display
will show following message: (for about 2 sec.)
Master
LCD shows the current controlling protocol
and selected device ID. „Master“ indicates
that the keyboard is currently set to „Master-
mode“
After about 2 seconds, the keyboard finishes the initialization and is ready to operate :
Select a device
CAM [ID]
[ID] can be any number between 1 –255.Please ensure that every device connected to the
keyboard has a valid and unique ID.For setting up the ID, please refer to the operating manual of
each device.
Master
To setup the keyboard in other controlling protocol, please refer to the section „Keyboard setup“ for
details.
XTS-2 CAM:001
2009 / 11 / 05
XTS-2 CAM:001
XTS-2 CAM:[ID]