Xview XVHWC User manual

XVHWC
USER MANUAL
xviewdrive.com.au
For more information
on the Xview range go
to our website
VIEW

2
6
7
1. PRODUCT DESCRIPTION
1) Vehicle Exclusive
Power Box
2) USB Connection Port
3) Male Bullet Connector
4) Ground Wire
5) Female Bullet Connector
1
2
4
38
9
6) Fuse (3 included)
7) Blade FuseTAP Connector
8) Mini Blade Fuse TAP Connector
9) Micro Blade Fuse TAP Connector
5

2. INSTALLATION
1.Find fuse box in car (fuse
the position differs among
different vehicle brands).
Consult vehicle user manual
for placement.
2. Open fuse box cover plate,
measure the placement for
wiring from fusebox to powered
product.
3. Plug in USB power device
3

Blade
Micro Blade
Mini Blade
2. INSTALLATION CONT...
4.Locate a ground point near
the fuse box. There is usually
either an obvious labeled
ground point or a nut / bolt that
connects directly to chassis.
5.Decide whether you want
your device wired to a switched
or unswitched fuse. Switched
circuits only have power when
the vehicle is ON. Unswitched
circuits always have power.
You can verify if it’s switched or
unswitched using a simple
circuit tester. NOTE: Make sure
your vehicle is off and the key
is not in the ignition. Choose
your desired TAP fuse. Once
you select the desired TAP
fuse for your vehicle, attach to
the power cable using the
bullet connectors, then cover
with plastic sleeve.
4

2. INSTALLATION CONT...
NOTE: This hardwire kit uses
easy to put together bullet
connectors. Attach each end of
bullet connector until you feel a
click.
6. Pull the fuse, place fuse into
the TAP fuse, then re-insert
into the available fuse slot.
5

Vehicle Headliner
Information below for Dash Cam installation
(A) Pillar
A pillar B pillar C pillar
2. INSTALLATION CONT...
7.Starting at the USB powered product,
tuck power cable into the headliner. Once
you get to the (A) pillar, there may be a
sufficient gap to place power cable or it may
be necessary to remove. The A pillar is the
plastic piece that runs down the side
separating the windshield and the door.
Route the power cable along the side and
behind the rest of the interior panels down
towards the fuse box.
6

3. SPECIFICATIONS
• The hard wire kit can have uninterrupted power for 24
hours if connected to vehicle battery or fuse box.
• It can stay powered on when your vehicle is turned
off.
• With function of auto detect battery voltage and low
voltage protecting, it can cut power supply when voltage
is too low, make sure the car can start normally.
• The vehicle hard wire kit is used as transforming 12V
or 24V to 5V, with built-in precise switching power supply
module, output voltage is more stable.
• Short-circuit protection: over-current and
over-temperture protection, reverse connection
protection, auto cut power output when it’s lower than
11.6V (for 12V connection) or 23.9V (for 24V
connection).
• Conversion efficiency: Max 96%
• Static power consumption: about 15-18mA
• Operating temperature: Industrial level (-40°C ~ +85°C)
Electrical Parameters
• Input voltage: DC12V - 30V
• Output voltage: 5V / 1.5A
• Car low voltage protection: 11.6V (for 12V connection)
• Car low voltage protection: 23.9V (for 24V connection)
7

4. USER SUPPORT
If you need assistance setting up or have an issue
regarding the use of your Xview product contact Xview
Customer Support.
Australian Agent
TEL: 03 – 8587 8898 FAX: 03 – 8587 8866
Mon-Fri 9am – 5pm AEST
Please retain this user guide for future reference.
For more information, manuals, software or other products
in the Xview range please go to our website.
Xviewdrive.com.au
This manual and product is considered correct at time of
printing but is subject to change. For latest manuals and
updates refer to the website.
8