XX.Y RUNNER 30 User manual

AX.V
SERA D> Pals O NE
WWW.XXY.@U
RUNNER 30
User guide

CD USER GUIDE
RUNNER 30 BLUETOOTH SPORTS EARPHONES
USE
1. Compatible with mobile phones and other mobile devices (including iPhone and iPad) supporting Bluetooth function.
Plays music, answers incoming calls wirelessly.
2. Compatible with PC computers supporting Bluetooth function (or Bluetooth USB adapter). Plays music or sounds from
multimedia files wirelessly.
BATTERY CHARGE
The headphones are powered by a built-in lithium-ion battery. Charge the battery to full capacity for at least 4 hours before
the first use. After the first use, the charging time is not more than 2 hours. The indicator light on the right earpiece is red
during charging. When the battery is fully charged, the indicator light turns blue. The battery run time is up to 5 hours.
To charge the battery, connect the headphones to the computer with a USB cable supplied. Using a car charger is not rec-
ommended during the first battery charge.
NOTE: The headphones may be used only after at least 40 minutes of battery charge.
KEY FUNCTIONS
S1: multifunction key Start/Pause, On/Off, Answer call/End call, Reject incoming call, Call back
S2: Previous: Play the previous track, Go into silent mode during call (mute)
S3: Next: Play the next track,
S4: Volume down
S5: Volume up
PAIRING WITH BLUETOOTH SUPPORTING DEVICES
©
Pairing is linking Bluetooth capable devices to establish permanent and secure connection allowing fast data transfer be-
tween the devices without each time entering a password.
1. Ensure the headset is turned off. Press and hold S1 button for about 10 seconds until you see red and blue lights flash-
ing alternately. Now the device is in paring mode and ready to be detected by other Bluetooth capable devices.
2. Activate Bluetooth function of the mobile phone/tablet/computer you want to pair with Runner 30. Refer to the mobile
phone/tablet/computer's manual if needed. The headphones will be detected as "Runner 30".
3. Select and confirm your Runner 30 out of those searched devices per the mobile phone/tablet/computer's manual.
4. When the headset indicator turns solid blue for 4 seconds, the pairing is complete. If the pairing process is unsuccess-
ful, please repeat steps 1 to 4.
NOTE:
The duration of the pairing process described in item 1 is 3 minutes. If the headset is not paired within this time,
it switches off automatically.

SWITCH ON AND OFF
SWITCH ON
Press and hold S1 button for 5 seconds until you see red and blue light flash at the same time. The device and a previously
paired mobile/tablet/computer (with activated Bluetooth function) will connect automatically. A flashing blue light indi-
cates that the connection is successfully established. If the connection is not established, the headset will switch off auto-
matically after 3 minutes.
SWITCH OFF
Press and hold S1 button for 3 seconds. Blue and red light will flash at the same time and turn off. The headphones are
switched off.
LIGHT INDICATORS
Slow flashing blue light The headset is connected to another device and ready for use
Slow flashing red light The headset is not connected to any device
Blue and red light flash alternately The headset is in pairing mode - ready to be detected
by another Bluetooth capable device
No light The headphones are switched off
BATTERY STATUS
Red light + audible signal in the headphones The remaining battery capacity is less than 10%
Red light Battery is charging
Blue light The battery is fully charged
USE
After the headphones and a mobile phone/tablet/computer are paired, you can answer calls and talk (mobile only) and
listen to music and sounds from the multimedia wirelessly.
DIALING FROM YOUR MOBILE
a) Select the number or contact you want to call on your mobile. Once the connection is established you will hear the call
in the paired Runner 30 headphones. During the call red light will flash two times a second. To end call, press S1 key
shortly.
b) Double press S1 key to redial the number you last called. To end call, press S1 key shortly.
ANSWERING INCOMING CALLS
The incoming call is indicated by an audible signal in the headphones and a solid red light.
WHEN YOUR MOBILE RINGS, YOU CAN
Answer the call: press S1 key shortly. Press the key shortly again to end your call.
Reject the call: double press S1 key.
DURING THE CALL
Volume adjustment: Increase or decrease the sound level by pressing S4 or S5 key respectively. Press and hold the keys
for smooth volume adjustment.
Ending your call: press S1 key shortly to end call.
MUTE MODE DURING CALL
If during a call you want to mute the loudspeaker and the microphone, press S2 key shortly. After an audible signal the
call will be muted in both directions. To exit the mute mode, press S2 key again.
MUTE MODE DURING CALL
Go to the previous track: press S2 key shortly
Go to the next track: press S3 key shortly
Pause/ Restart: press S1 key shortly
MAXIMUM VOLUME LEVEL
For safety reasons RUNNER 30 headphones have a sound level limiter to prevent
blocking out external noises during workout.