Xyron 900 User manual

MODEL
900
Makes
items up
to 9” wide.*
Use it
anywhere!
No heat.
No electricity.
No batteries.
* Adhesive cartridge 9” wide,
all others 8.5” wide.
2
3
1
Label Maker
Laminator
Sticker Maker
Magnet Maker
USER MANUAL

The Xyron®900 helps transform your creative ideas and memories
into reality. An improved and patented Easy Loading Cartridge offers
you all the flexibility and quality you expect from Xyron.
Without heat, electricity, or batteries, the Xyron 900 allows you to
effortlessly apply adhesive, laminate or magnet to your document
or project. Get started today making your projects look the way
they make you feel!

Machine Features
The “X-Grip” Handle is soft and
durable, giving a smooth feel
when enhancing items.
The patented Easy Loading Cartridge design
allows you to change from adhesive to lami-
nate to magnet in just seconds.
The Input Tray folds up
for easy storage and pro-
tects the machine
and cartridge from
dust and debris.

The new Removable Cutter gives you
the freedom to trim your document both
in and out of the machine. Use it for
anything you need to take the edge off!
Built-in Grip/Carry Handle
to take your Xyron 900
almost anywhere.

Step 1: Place item flat on the tray, aligned all the way to the
left side. Guide the item forward while slowly turning
the handle clockwise.
With just a few simple, easy-to-follow steps,
you’ll be protecting and enhancing your creativity:
Step 2: After the item is completely visible on the output tray,
trim the item by sliding the blade across the material.
Step 3: Gently lift up the cutter tray and slide it out. Use the
cutter to trim the rest of the item if necessary.
For adhesive, remove the clear mask and peel off
the sticky-back item.

How to replace the cut blade: Loosen and remove the screw
in the cut bar with wrench. Remove colored plastic insert and slide
the old blade off the cut bar (safely discard old blade). Carefully
slide the NEW Xyron 900 blade onto clear bar. NOTE: The sharp
edge of the blade should be facing inward. Replace the colored
plastic insert into clear bar and secure screw with wrench. Verify
smooth movement across the entire length of the clear bar.
How to replace the cutter assembly: Align the cutter sides
with the machine. Slide in the cutter with the cut bar resting on the
spring arms on the side of the machine until it snaps and locks
into place.
How to load the cartridge: Open the lid to your Xyron 900
machine. Slide the cartridge into the tracks on the sides of the
machine with the exposed rolls of material facing the open lid
cover. Close the lid securely. Advance film and trim.

• Make sure the cartridge is installed correctly prior to using the machine.
• For best results, turn the handle slowly.
• Arrange small items (without overlapping them) on the feed tray to
maximize your cartridge material use.
• Use items that are 1/10 of an inch thick or less.
• Test before using one-of-a-kind items.
• Watch for the “End-of-Roll” marker 18˝ from the end of Laminate and
Magnet cartridges. To remove marker, simply peel it off the laminate.
Adhesive:
• For best results, apply pressure with finger or dull tool around the
edge of the object prior to removing the clear plastic film.
• If there is excess adhesive around the edges of an item, simply wipe
off with your fingers. The adhesive comes right off without sticking to
your hands.
• Clean off adhesive buildup from the rollers with any adhesive
remover or rubbing alcohol.
Helpful Hints

• Acid-Free Permanent Adhesive is safe for scrapbooking. Acid-Free
Repositionable Adhesive is safe for windows, painted walls and
doors, and it does not leave any residue on most surfaces. Test on
an inconspicuous area first.
Laminate:
• It is not recommended for one-of-a-kind items since the process is
permanent (use copies of photos and other valuable items).
• Make sure there is adequate space between each item you are lami-
nating. Overlapping will cause the items to be laminated together.
• Two-Sided Lamination allows you to cut right to the edge or com-
pletely through the item you are protecting. It will not separate!
Magnet:
• To maximize the material when making a magnet frame, place a
smaller item in the middle of the frame. This way, even the magnet
material in the middle of the frame is being used. Keep other paper
supplies and photos handy for magnetizing.
Always be CREATIVE!
Additional Helpful Hints

Applications
Crafts: Scrapbooking (memory books), rubber stamping, fabrics
School: Class projects, book covers, labels, teaching aides, flash
cards, certificates, awards
Home: Recipe cards, labels, children’s projects, newspaper
articles, decorations, photos
Home Office: Presentations, signs, training tools, sales forecasts,
brochures, labels, business cards

Machine Specifications
Footprint: 7.75" W x 14.5" L x 6.75" H (19.7 cm x 37 cm x 17.1 cm)
Weight: approximately 6 lbs (2.72 kg)
Packed Weight: approximately 7 lbs (3.17 kg)
Maximum Document Thickness: 0.10" (2.54 mm)
Maximum Document Width: 9" (22.86 cm)
Maximum Document Length: Cartridge Dependent
Power Source: NONE
Cutter Assembly: Removable, with available replacement blade
Manufactured: Some parts and assembly in both USA and China
XYRON, Inc. Scottsdale, AZ, USA www.xyron.com
Replacement Cartridges
Acid-Free Permanent Adhesive (9" wide) Photos, scrapbooking, rubber stamping, vellum paper, etc.
Acid-Free Repositionable Adhesive (9" wide) Kids’ stickers, art and science projects, stenciling, games,
crafts, etc.
Permanent Adhesive (9" wide) Home décor, holiday décor, ornaments, gift making, fabric appliqués, etc.
Two-Sided Lamination (8.5" wide) Photos, bookmarks, recipes, ID and business cards, tags and labels, etc .
Laminate/Acid-Free Permanent Food jar and packaging labels, shipping labels, signs and
Adhesive Backing (8.5" wide) banners, displays, greeting cards, etc.
Laminate/Acid-Free Repositionable Door and window signs, kids’ stickers, teaching aids, graphs,
Adhesive Backing (8.5" wide) badges, etc.
Lamination/Magnet Backing (8.5" wide) Photo magnets, frames, business cards,
shopping and to do lists, etc.