YAGUD ZF-0301 User manual


Table of contents
instructions for Safe use
Packing list
Product description
Remote control key description and pairing
Operation instructions
Plate lubrication
Running belt elastic adjustment
Exercise advice
Failure and maintenance
Warranty description

Thank you for choosing our products. The correct use of the walking machine is your
guarantee of safety and convenience. Please read the following carefully before using the
walking machine:
1. Power on only after confirming that the electric walking machine has been installed in
accordance with the installation instructions. Be careful not to make it block the plug on the
wall when placed, and leave 0.8m space in front for easy insertion.
2. Reserve 0.8m safety space on both sides of the walking machine, and 2 m (length) *1 m
(width) safety space behind the walking machine.
3. Insert the power cord into the power socket with safe grounding. The power supply of the
electric walking machine is dedicated. If the power cord is damaged, please consult the
after-sales staff of the platform, or contact the company directly, and send it to you by mail.
Plug in the corresponding place.
4, walking machine is indoor equipment, do not use outside. The place is clean and smooth,
pay attention to moisture-proof, and pay attention not to put the walking machine on the
thick carpet, so as not to affect the flow of air under the walking machine. Electric walking
machine is a special instrument, please do not modify it.
5, exercise can not wear too big, too loose clothes, can not wear slippers type shoes, in order
to prevent hanging on the electric walking machine to cause safety accidents. Running
shoes or exercise shoes with rubber soles are recommended.
6. Please do not remove the protective cover. If it needs to be opened for maintenance,
please remove the power cord first.
7, electric walking machine in use, do not let children, pets close to prevent danger.
8. If you use the electric walking machine for the first time, the speed can not be too fast.
Adjust the speed of the electric walking machine according to your own physical ability.
9. If the electric walking machine suddenly accelerates or the speed of the walking machine
automatically increases due to the problem of the electronic watch system, please press the
stop button of the remote control immediately, and the electric walking machine will stop
immediately.
10. If the electronic system fails and cannot be stopped, please jump away from the walking
area quickly and turn off the power in time.
11, electric walking machine when not in use, should unplug the power cord.
12. Minors should be accompanied by adults when using electric walking machines.
Instructions for Safe Use
1

Packing list
1. Packing list
2. Attached Table (List of parts Package)
3. Technical parameter
No. Name Quantity Remarks
1Complete machine (running
platform) 1
2 Accessory bag 1
1
See
attached
table
3Specification
No. Name Quantity Remarks
1 6MM hex wrench 1
2 Remote control 1
3 Dual-purpose screwdriver 1
1
4
5
Silicone oil 2 30ml
Model
Operating
voltage 110V 50/60Hz
Maximum
load
Overall
dimension
Effective
running area
Machine
weight
Peak motor
power 0.75-2.0HP
speed 0.6-3.8mph
function walk
2
198 lbs
51.8 lbs
49.8×20.3×4.7 inch
40.1×15.3 inch
ZF-0301
Button battery

M
START
STOP
Speed increase
mode key
Speed reduction
Start key
cease
Product description
Time countdown mode velocity Distance Countdown Mode
Calorie Countdown Mode
3
2.Electronic display
1.Walk treadmill
Power switch
ON
OFF

Remote Control Description
Key function description
Speed increase
In the running state, the running speed value can be increased to 0.2mph each time
deceleration
In the running state, the speed value can be reduced to 0.2mph per run
Usage pattern The machine has four operating modes:
Mode 1: Speed mode
Mode 2: Time countdown mode
Mode 3: Distance reverse meter mode
Mode 4: Calorie count mode
Press a button to switch
Start key Start the walking machine Stop key Press the motor to stop running
4
M
START
STOP
Attention:
Open the battery rear cover
1
2
1、First place one hand in this groove
and apply force in thisdirection
2、At the same time, place the other
handon the raised patternand apply
force in this direction
Attention:
The plastic sheet must
be removed before use
Note:
The remote control has been paired with the treadmill before delivery and can be used
directly
If you need to pair again, the matching method is as follows: before the treadmill is
powered on, hold down the start button of the remote control (within 10cm of the treadmill
display screen); then, when the treadmill is powered on, the buzzer will ring five times
quickly and the treadmill will enter the standby state, indicating successful pairing. At this
time, you can release the button; If the buzzer does not ring five times quickly after the
treadmill enters the standby state, the pairing fails.

Operation instructions
5
Flip the switch to turn on the treadmill
The function indicator jumps automatically after 00 , 8 seconds on the initial screen
Mode 1: speed mode
Stand on the treadmill
Press the Start button, countdown 5 seconds to start running
The initial treadmill speed is 0.6MPH. Press +/- to adjust the speed
Time, speed, distance, calorie four interface jump in turn
Time timing,The machine will stop automatically if the time exceeds 99:59
Press stop to exit the mode and return to the initial screen
Mode 2: Time countdown mode
Stand on the treadmill
Press M to switch to H - 1
Wait until the screen blinks at 30:00 and press the +/- key. The adjustable range is from 8:00 to
99:00
Press the Start button, countdown 5 seconds to start running
The initial treadmill speed is 0.6MPH. Press +/- to adjust the speed
Time, speed, distance, calorie four interface jump in turn
Distance and calorie count
Press stop to exit the mode and return to the initial screen
Mode 3: Distance reverse meter mode
Stand on the treadmill
Press M to switch to H - 2
Wait until the screen blinks 1.00 and press +/- to adjust. Adjustable range :1.00-99.00
Press the Start button, countdown 5 seconds to start running
The initial treadmill speed is 0.6MPH. Press +/- to adjust the speed
Time, speed, distance, calorie four interface jump in turn
Time and calories count
Press stop to exit the mode and return to the initial screen
Mode 4: Calorie count mode
Stand on the treadmill
Press M to switch to H - 3
Wait until the screen flashes 50.00 and press +/- to adjust the value. Adjustable range :20-990
Press the Start button and countdown 5 seconds to enter
Press the +/- key to adjust the speed
Time, speed, distance, calorie four interface jump in turn
Time and distance count positively
Press stop to exit the mode and return to the initial screen

1. No stop function: After starting the treadmill, if no one runs for more than five seconds, the
treadmill will automatically stop
2. Hibernation function: When the treadmill stops running, if there is no operation for more
than 10 minutes, it will enter hibernation state. The electronic watch will automatically close
the display and press any key to wake up
Note
1, we mentioned above should be timely to the running plate lubrication, but not
excessive lubrication, lubricant is not the more the better. Remember: reasonable
lubrication is an important factor to improve the service life of the walking machine.
2, check whether you need to put on the lubricant, as long as you grab the running
belt, touch your hand as far as possible to the center of the back of the running belt, if
your hands are stained with silicone oil (a little wet feeling), that is, you do not need to
put on the lubricant, if the running board is dry and hands did not stick to the silicone
oil, you need to add lubricating silicone oil.
3, the running board coated with lubricating silicone oil steps:
a. Set the walking machine to a low speed running 0.6mph;
b. Open the cover on the right side of the front end of the ru nning platform under the
refueling mark; Insert the spout into the nozzle of the filling tube and gently squeeze
the oil can to spray the silicone oil onto the running belt. Run the treadmill at 0.6 MPH
/h to evenly apply the silicone oil. Gently step on the running belt from left to right for
8 to 10 minutes until the silicone oil is completely absorbed into the running belt.
All walking machines should be adjusted before leaving the factory and after installa-
tion, but there may be slack phenomenon after a period of use. For example: when the
user runs, there is a pause and skid. When this phenomenon occurs, in the clockwise
direction of half a circle as a unit, the left and right synchronous adjustment belt
adjustment bolt. (If you want to loose running belt, on the contrary, in the counter-
clockwise direction of operation) run belt loose, foot in the running belt, running belt
and drum will produce skid phenomenon, but too tight is not good, easy to increase
the load of the motor, damage the motor, running belt and drum.
The running belt is centered
Plate lubrication
Running belt elastic adjustment
6

If the belt deviates to the left,
adjust the left screw clockwise
or adjust the right screw
counterclockwise
If the belt deviates to the right,
adjust the right screw clockwise
or adjust the left screw
counterclockwise
Exercise advice
1. Put the electric walking machine on the flat ground.
2. Run an electric walker at about 2.0mph.
3. If the running belt is tilted to the left, rotate the left adjusting bolt 1/2 turn clockwise
and the right adjusting bolt 1/2 turn counterclockwise
4. If the running belt is biased to the right, rotate the right adjusting bolt in a clockwise
direction for 1/2 turn, and then rotate the left adjusting bolt in a counterclockwise
direction for 1/2 turn
Consult a professional before exercising. He can help you recommend the frequency,
intensity and duration of exercise appropriate for your age and physical condition. If
you feel chest tightness or pain, irregular heartbeat, shortness of breath, dizziness or
other discomfort while exercising, please stop immediately! Consult a professional
before continuing to exercise.
prepare
Before exercise, it is necessary for you to understand your own health status, in order
to make their own exercise plan, it is recommended to consult a doctor or professional,
maybe you can get twice the result with half the effort.
efore using the electric walking machine for the first time, please stand next to it and
familiarize yourself with how to control it: start, stop and speed adjustment, etc.,
before you can use it. Then stand on the plastic anti-skateboard on both sides of the
walking machine, grab the handrail with both hands, open the machine to a low speed
Running belt elastic adjustment
7

Do it again at the end of your workout.
of 1.6~3.2 km/h, stand up straight, look forward, use one foot in the running belt
"climb" a few times, as relaxed as possible: then stand on the running belt with its
movement. After feeling comfortable, slowly increase the speed to 3-5 km/h. Keep
going at this speed for about 10 minutes, then slowly bring the machine to a stop. Do
not run at high speed for the first time to avoid falling.
1. Stretch down
Bend your knees slightly and slowly bend forward, letting your back and shoulders
relax and touching your toes with your hands. Hold for 10-15 seconds. Then relax.
Repeat 3 times on each leg
2. Stretching of hamstrings
Sit on a clean cushion and stretch one leg straight. Pull the other leg in so that it fits
snugly against the inside of the extended leg. Try to touch your toes with your hands.
Hold for 10-15 seconds, then relax. Repeat 3 times on each leg.
3. Stretch the little foot and heel tendon
Stand with two hands against a wall or tree, one foot behind. Keep your hind legs
upright and your heels on the ground, leaning toward a wall or tree. Hold for 10-15
seconds, then relax. Repeat 3 times on each leg
4. Quadriceps stretch
Balance on a wall or table with your left hand, then reach back with your right hand,
grab your right ankle and slowly pull toward your hip until you feel tension in the front
of your thigh. Hold for 10-15 seconds, then relax. Repeat 3 times on each leg.
5. Sartorius (inner thigh muscles) stretch
Sit with your feet facing each other and your knees facing out. Grab your feet with
both hands and pull toward your groin. Hold for 10-15 seconds, then relax. Repeat 3
times.
8

9
E01:
Common Problem
Solving Methods
E02:
Common Problem
Solving Methods
E03:
Common Problem
Solving Methods
E04:
Common Problem
Solving Methods
E05:
Common Problem
Solving Methods
The communication line of the
electronic watch is not properly
connected, broken, and has poor
contact
Please reconnect the
communication cable
Replace the electronic watch and
wait for repair
Replace the lower control and
wait for repair
Electronic watch has no
signal output
No signal output from
lower control
The motor wire is not properly
connected
Check if the motor wires are
connected correctly
Replace the lower control and
wait for repair
Replacing the motor
Poor motor
No voltage output or abnormal
voltage output from the lower
control to the motor
The treadmill has a large load
exceeding the rated working
voltage of the motor
It is recommended to use it within
the rated working voltage range of
the motor
Replacing the motor
Replace the lower control and
wait for repair
Failure of the motor overvoltage
measuring circuit on the lower
control board
Abnormal treadmill motor
The treadmill load exceeds
the rated working current
of the motor
It is recommended to operate
within the rated current range
of the motor
Check if the structure of the
treadmill is normal
Fault in the lower control
current limiting system
Replace the lower control and
wait for repair
Problem with the assembly structure
of the treadmill and motor, causing
motor resistance or blockage
The power supply voltage
is too low
Please check if the power supply
line is normal
Replace the lower control and
wait for repair
The testing circuit of the lower
control board is invalid
Failure and maintenance

Important information:
We are not responsible for any failure caused by incorrect installation, use or replacement
of parts by customers themselves. In addition, the warranty does not apply to the person
who has not been authorized by the Company to repair, if the resulting repair costs, the
customer himself shall be responsible.
This product is for home use only. The company will not be responsible for any problems
caused by commercial use.
The warranty lasts for 1 year
Warranty description
10
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for aClass B digital
device, pursuant to part 15 ofthe FCCRules. Theselimits aredesigned to provide
reasonable protection against harmful interference in a residential installation. This
equipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalled
andused inaccordance withthe instructions,may causeharmfulinterferencetoradio
communications.However,there isno guaranteethatinterferencewill notoccur ina
particularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Thisequipment complies withFCC radiation exposure limits setforth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Table of contents