Yale Aeron Remote User manual

Aeron® Remote
User Guide

2
Individual window pairing
• A maximum of 30
individual windows and
can be controlled via the
remote
OPERATING WINDOWS
For windows to be controlled via a remote the remote must
be paired with the Yale Connect Plus Hub 2. Windows can
be paired to operate as a group or individually.
Remote is used for the following functions
• Window control
• Pairing Aeron window actuators
• Pairing Connect Plus Hub 2
• Creating window Groups
• Deleting windows or Groups
Group pairing
• A maximum of 4 Groups can be
controlled via the remote. Note:
no more than 30 actuators can be
assigned across all 4 groups.
• Group 1 by default are all the actuators.
This group cannot be editted. Only
groups 24 can be editted.

3
Remote overview
Default state:
Box content
• Remote x 1
• Cradle x 1
• AA Batteries x 2
• Screws x 2 and actuator plugs x 2
• Quick starter guide x 1
Note: Remote is held into the actuatorll
cradle with magnets.
LED Light
Open/Stop
Previous Next
Close/Stop
LCD Screen
Control Buttons
Default state
after pairing
No window connected
Click: switch control mode
Long Press: enter add/del mode

4
LCD SCREEN
All Icons Device Control Group Control Add Delete No Actuators
in Group

5
GROUP CONTROL
Note: the remote has maximum four groups. User cannot customise # of groups.
Switch to group control Open a group of windows
Close a group of windows
Select window group
1. At device control state 1. At device control state
1. At device control state
2. Click CONFIRM 2. Click OPEN
2. Click CLOSE
3. Final State 3. Window opening
(LED light up; left & right
arrow disappear)
3. Window closing
(LED light up; left & right
arrow disappear)
4. Click OPEN again,
to stop opening
4. Click CLOSE again,
to stop opening
NEXT Group
PREVIOUS Group

6
DEVICE CONTROL SINGLE WINDOW
Switch to device control Open a window
Close a window
Select window group
1. At device control state 1. At device control state
1. At device control state
2. Click CONFIRM 2. Click OPEN
2. Click CLOSE
3. Final State 3. Window opening
(LED light up; left & right
arrow disappear)
3. Window closing
(LED light up; left & right
arrow disappear)
4. Click OPEN again,
to stop opening
4. Click CLOSE again,
to stop opening
NEXT Group
PREVIOUS Group

7
ADDING MODE
Add a window actuator to a group
Enter adding mode
Exiting adding mode
Find the Actuator to add
Add to group (group 1)
CONFIRM
1. At group
control state
1. Click OPEN
or CLOSE
1. At group
control state
1. Click
CONFIRM
2. Press
CONFIRM for 3
seconds
2. Final state 2. Press CONFIRM
for 3 seconds
3. LED flashes red
2. Final state3. Enter adding mode, indicator, switch to
Actuator, Actuator flashes
(showing all window actuators)
Use Left or Right control buttons to find the
window actuator required to be added

8
DELETING MODE
Delete a window actuator from a group
Enter deleting mode
Quit deleting mode
Find the Actuator to add
Add to group (group 1)
CONFIRM
1. At device
control state
1. Click OPEN
or CLOSE
1. At device
control state
1. Click
CONFIRM
2. Press CONFIRM
for 3 seconds
2. Final state 2. Press CONFIRM
for 3 seconds
3. LED flashes red in delete
mode. Press central control
button to confirm selection
2. Final state3. Enter deleting mode, Actuator flashes
(showing all window actuators)
Find actuator you actuatornt to delete using
Right or Left buttons

9
PAIRING MODE
How to pair Aeron actuators when in pairing mode
Enter pairing mode Pairing request to Actuators
1. Press CONFIRM
& OPEN for 5s-10s
Note: It is only necessary to go through the above pairing steps if
the unit has been powered on longer than 5 minutes
1. Press CONFIRM
& CLOSE for 5s-10s
2. Pairing (green
light blinking)
2. Signal sent
successfully (green
light turns on for 1s)
3. Success
(solid green)
3. Failed sending
signal, red light
flashes twice
4. Fail (red light
flash twice)

10
FACTORY RESET
Single Actuator reset Group Actuators reset
1. Press CONFIRM
& NEXT for 5s-10s
1. Press CONFIRM
& NEXT for 5s-10s
2. Signal sent
successfully (green
light turns on for 1s)
2. Signal sent
successfully (green
light turns on for 1s)
3. Failed sending
signal, red light
flashes twice
3. Failed sending
signal, red light
flashes twice
If required, a single actuator can be factory reset when it is
not performing correctly. Ensure the actuator that is to be
reset is selected then follow the steps below.
If required actuators in a Group can be factory reset when the
actuators are not performing correctly. Ensure the actuator that
is to be reset is selected then follow the steps below.
Note: Single actuator reset can also be performed via
the setting in the app.