Yamaha DVD-S1800 User manual
_YAMAHA
DVD AUDIONIDEO SA-CD PLAYER
LECTEUR DVD AUDIONIDEO SA-CD
DVD-S1800
OWNER'S MANUAL
MODE
D'EMPLOI
III I
IMPORTANT SAFETY INSTRUCTIONS
12
Grounding or Polarization -This product may be equipped with
apolarized alternating current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only
one way. This
is
asafety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should
still fail to tit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose
of
the polarized plug.
13
Power-Cord Protection -Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit
from the product.
14
Lightning -For added protection for this product during a
lightning storm,
or
when it is left unattended and unused for long
periods
of
time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product
due to lightning and power-line surges.
15
Power Lines -An outside antenna system should not be located
in
the vicinity
of
overhead power lines or other electric light
or
power circuits, or where it can fall into such power lines
or
circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
16
Overloading -Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in
arisk
of
fire
or electric shock.
17
Object and Liquid Entry -Never push objects
of
any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in afire or
electric shock. Never spill liquid
of
any kind on the product.
18
Servicing -
Do
not attempt to service this product yourselfas
opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
19
Damage Requiring Service -Unplug this product from the wall
outlet and refer servicing to qualified service personnel underthe
following conditions:
a)
When
the
power-supply
cord
or
plug
is
damaged,
b)
If
liquid has been spilled,
or
objects
have
fallen into the
product,
c)
If
the product has been
exposed
to rain
or
water,
d)
If
the
product
does not operate normally by following the
operating instructions.
Adjust
only
those controls
that
are
covered
by
the
operating
instructions as
an
improper
adjustment
of
other
controls
may
result in
damage
and
will often require extensive
work
by aqualified
technician to restore
the
product to its normal operation,
e)
If
the product has
been
dropped
or
damaged
in any way,
and
f)
When
the
product
exhibits adistinct
change
in
performance -this indicates a
need
for service.
20
Replacement Parts -When replacement parts are required, be
sure the service technician has used replacement parts specified
by
the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock,
or
other hazards.
21 Safety Check -Upon completion
of
any service
or
repairs to
this product, ask the service technician to perform safety checks
to determine that the product
is
in proper operating condition.
22
Wall
or
Ceiling Mounting -The unit should be mounted to a
wall
or
ceiling only as recommended by the manufacturer.
23
Heat -The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
RISK
OF
ELECTRIC
SHOCK
00
NOT
OPEN
CAUTION:
TO
REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
9
Read Instructions -All the safety and operating instructions
should be read before the product is operated.
Retain Instructions -The safety and operating instructions
should be retained for future reference.
Heed Warnings -
All
warnings on the product and
in
the
operating instructions should be adhered to.
Follow Instructions -All operating and use instructions should
be followed.
Cleaning -Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners
or
aerosol cleaners. Use a
damp cloth for cleaning.
Attachments -Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
Water and Moisture -Do not use this product near water -for
example, near abath tub, wash bowl, kitchen sink,
or
laundry
tub;
in
awet basement;
or
near aswimming pool; and the like.
Accessories -
Do
not place this product on an unstable cart,
stand, tripod, bracket,
or
table. The product may fall, causing
serious injury to achild or adult, and serious damage to the
product. Use only with acart, stand, tripod, bracket,
or
table
recommended by the manufacturer, or sold with the product.
Any mounting
of
the product should follow the manufacturer's
instructions, and should use amounting accessory recommended
by the manufacturer.
Aproduct and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart
combination to overturn.
10
Ventilation -Slots and openings
in
the
cabinet are
provided for ventilation and to ensure reliable operation
of
the
product and
to
protect it from overheating, and these openings must
not
be
blocked or covered. The openings should never
be
blocked
by
placing the product on abed. sofa. rug, or other similar surface.
This product should not
be
placed
in
abuilt-in installation such
as
a
bookcase or rack unless proper ventilation
is
provided or the
manufacturer's instructions have been adhered
to.
11 Power Sources -This product should be operated only from the
type
of
power source indicated on the marking label. If you are
not sure
of
the type
of
power supply to your home, consult your
product dealer
or
local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
8
7
6
4
5
2
3
1
•Explanation
of
Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended
to
alert you to the
presence
of
uninsulated "dangerous voltage" within the
product's enclosure that may
be
of
sufficient magnitude
to
constitute arisk
of
electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence
of
important
operating and maintenance (servicing) instructions
in
the literature accompanying the appliance.
iEn
FCC INFORMATION (for US customers)
I. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained
in
this manual, meets FCC requirements. Modifications
not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/
ssupplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your
FCC authorization to use this product
in
the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed
in
FCC Regulations, Part
15
for Class
"B"
digital devices.
Compliance with these requirements provides areasonable level
of
assurance that your use
of
this product
in
aresidential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful
to the operation
of
other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur
in all installations. If this product
is
found to be the source
of
interference, which can be determined by turning the product
"OFF" and "ON", please try to eliminate the problem
by
using one
of
the following measures:
Relocate either this product or the device that
is
being affected
by
the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits
or
install AC line filter/s.
In
the case
of
radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type
of
product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe Ave.
Buena Park, CA90622.
The above statements apply ONLY to those products distributed
by
Yamaha Corporation
of
America or its subsidiaries.
We Want
You
Listening For ALifetime
Yamaha and the Electronic Industries Association's Consumer Electronics Group want
you
to
get the most out ofyour equipment
by
playing
it
at
asafe level. One that lets the sound come through loud and clear without annoying blaring or distortion -
and,
most importantly, without affecting your sensitive hearing.
Since hearing damage
from
loud sounds
is
often undetectable until
it
is
too late, Yamaha and the Electronic Industries
Association's Consumer Electronics Group recommend
you
to
avoid prolonged exposure
from
excessive volume levels.
CLASS 1LASER PRODUCT
LASER KLASSE 1PROOUKT
lUOKAN
1
lASERlAITE
KLASS 1
lASER
APPARAT
PRODUIT
LASER
DE
CLASSE 1
For Customer Use:
Read carefully the information located at the rear panel
of
this
unit and enter below the Serial No. Retain this information for
future reference.
Model No.
Serial No. _
CAUTION
Use
of
controls or adjustments
or
performance
of
procedures
other than those specified herein may result
in
hazardous
radiation exposure.
CAUTION-VISIBLE
AND
INVISIBLE
LASER
RADIATION
WHEN
OPEN.
DO
NOT
STARE
INTO
BEAM
OR
VIEW
DIRECTLY
WITH
OPTICAL
INSTRUMENTS.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam.
When this unit is plugged into awall outlet, do not place your
eyes close to the opening
of
the disc tray and other openings or
look inside.
ii
En
CAUTION:
READ
THIS
BEFORE
OPERATING
THIS
UNIT.
WARNING
TO REDUCE
THE
RISK
OF
FIRE OR ELECTRIC
SHOCK, DO
Nar
EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
LASER SAFETY
This unit employs alaser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt
to service this device.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade
of
plug to
wide slot and fully insert.
This Class Bdigital apparatus complies with Canadian
ICES-003.
The unit is not disconnected from the
AC
power source as
long
as
it
is
connected to the wall outlet, even if this unit
itself
is
turned off. This state is called the standby mode.
In
this state, this unit
is
designed to consume avery
smal1
quantity
of
power.
Semiconductor laser GaAIAs
650 nm (DVD)
790 nm (VCD/CD)
1.45
mW
(DVD)
1.13 mW (VCD/CD)
60 degreesBeam divergence
Output Power
LASER
Type
Wave length
15
Be sure to read the "TROUBLESHOOTING" section on
common operating errors before concluding that this unit
is
faulty.
16
Before moving this unit, press STANDBY/ON to set the
unit
in
standby mode, then disconnect the
AC
power plug
from the wall outlet.
17 Install this unit near the
AC
outlet and where the
AC
power plug can be reached easily.
18
The batteries
shal1
not be exposed to excessive heat such
as sunshine, fire or the like.
1
To
assure the finest performance, please read this manual
carefully. Keep it
in
asafe place for future reference.
2Install this unit
in
awell ventilated, cool, dry, clean place
-away from direct sunlight, heat sources, vibration,
dust, moisture, or cold.
In
acabinet, allow about 2.5 cm
(I inch)
of
free space all around this unit for adequate
ventilation.
3Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., aroom with ahumidifier) to
prevent condensation inside this unit, which may cause
an
electrical shock, fire, damage to this unit, and/or personal
injury.
5Avoid installing this unit
in
alocation where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top
of
this
unit, do not place:
-Other components, as they may cause damage and/
or discoloration on the surface
of
this unit.
-Burning objects (i.e., candles), as they may cause
fire, damage to this unit, and/or personal injury.
-Containers with liquid
in
them,
as
they may fall,
spilling the liquid and causing an electrical shock to
the user and/or damage to this unit.
6Do not cover this unit with anewspaper, tablecloth,
curtain, etc.
in
order not to obstruct heat radiation.
If
the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7Do not plug in this unit to awall outlet until all
connections are complete.
8Do not operate this unit upside-down.
It
may overheat,
possibly causing damage.
9Do not use excessive force on switches, knobs and/or
cords.
10 When disconnecting the power cord from the
wal1
outlet,
grasp the plug; do not
pul1
the cord.
11
Do not clean this unit with chemical solvents; this might
damage the finish. Use aclean, dry cloth.
12 Use only the voltage specified on this unit. Using this unit
with ahigher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage
resulting from use
of
this unit with avoltage other than as
specified.
13
Do not attempt to modify or
fix
this unit. Contact
qualified Yamaha service personnel when any service
is
needed. The cabinet should never be opened for any
reason.
14
When not planning to use this unit for long periods
of
time (i.e., vacation), disconnect the
AC
power plug from
the wall outlet.
iii
En
CONTENTS
INTRODUCTION 3
Playable
disc
formats 3
DVD region codes 3
Patent information 4
Cleaning
discs
4
Supplied accessories 4
FUNCTIONAL OVERVIEW 5
Front panel 5
Front panel
display
6
Rear panel 7
Remote control 8
CONNECTIONS 10
General notes
on
connections 10
Audio
connections 10
Connecting astereo amplifier
10
Connecting an AV receiver with 6chl
multi-channel input
10
Video connections
11
HDMI connection 12
Connecting the power cable 14
GETTING STARTED 15
Step 1: Inserting batteries
into
the remote control................................... 15
Using the remote control
15
Step 2: Turning on the power 15
Step 3: Setting aTV
type
16
Step 4: Setting alanguage preference 17
Setting the OSD (On-Screen Display)
language
17
Setting the audio, subtitle and
disc menu languages .
17
DISC OPERATION 18
Basic operation
18
Pausing playback
18
Selecting atrack/chapter
18
Searching backward/forward
19
Repeat playback 19
Repeating playback
19
Repeating asection
(except DVD-Audio/MP3/WMA/JPEG) ......
19
Random playback
(except DVD/SA-CD) 19
Program playback (CD)
20
Disc menu operation
(DVDNCD/SVCD)
20
Using the DVD menu 20
Using the Video CD playback control (PBC)
menu (VCD/SVCD)
21
On-screen display(OSD) menu
(DVDNCD/SVCD/SA-CD)
21
Using the OSD menu
(DVDIVCD/SVCD/CD)
21
Displaying text information (SA-CD) 22
Picture Setting menu
(DVDNCD/SVCD)
22
Adjusting picture settings 22
Zooming pictures
(DVD-VldeoNCD/SVCD/DivX®/JPEG)
23
Viewing angles (DVD-Video)
23
Audio
and Subtitle languages
(DVD-VldeoNCD)
24
Selecting an audio language 24
Selecting asubtitle language
(DVD-Video) 24
DivX® external subtitle files
24
Changing pages (DVD-Audlo) 24
Group/File selection (DVD-Audio/DlvX®/
MP3IWMAIKodak picture CD)
25
Selecting agroup (DVD-Audio) 25
Selecting afile
in
afolder
(DivX®/MP3/WMA/Kodak picture CD) ...... 25
Bonus
group
playback
(DVD-Audio)
25
Changing the playback area
and layer(SA-CD)
25
Multimedia file playback
(MP3IWMAlDivX®/JPEG)
26
Displaying the thumbnail screen (JPEG) 26
Rotating pictures (JPEG) 26
Continued
1En
CONTENTS
,SETUP MENU 27
Menu overview............................................ 27
Setup menu operation 28
General setup menu 29
Selecting DVD-Audio mode 29
Selecting SA-CD mode 29
Setting the OSD language 29
Restricting playback with parental control 29
Changing the parental password 29
Setting the screen saver 30
Setting the auto power function 30
Setting the sleep timer 30
Resetting the system 30
Displaying the DivX® VOD
registration code 30
Audio setup menu
31
Setting the analog output
31
Setting the digital output
31
Setting the LPCM output 3I
Setting the night listening mode
31
Speaker setup menu 32
Setting speaker sizes 32
Setting speaker distances 32
Setting speaker levels 33
Setting the SA-CD configuration 33
Video setup menu 34
Setting the TV display 34
Setting the TV type 34
Selecting the wide screen format 34
Selecting the black level
(U.S.A. and Canada models only)
35
Selecting the closed caption
(U.S.A. and Canada models only)
35
Setting the still mode 35
Selecting the scan function 35
Switching the SCART video out
(U.K., Europe, and Russia models only) 36
HDMI setup menu 36
Setting the HOMIvideo 36
Selecting the DVI output range 37
Setting the HDMI audio
37
DISC setup menu 37
Selecting the default audio/subtitle/
DVD menu language 37
Selecting an angle mark display 37
Selecting the PBC (playback control)
function 38
Setting the duration for aslide show 38
2
En
LANGUAGE CODE LIST
39
TROUBLESHOOTING
40
GLOSSARY
42
I
SPECIFICATIONS 44
INTRODUCTION
Thank you for purchasing this unit. This Owner's Manual
explains the basic operation
of
this unit.
•Illustrations
in
this manual are based on the U.K.,
Europe, and Russia models unless otherwise specified.
•Notes contain important information about safety and
operating instructions.
•
:'4<~
indicates atip for your operation.
•This manual is printed prior to production. Design and
specifications are subject to change in part as aresult
of
improvements, etc. In case
of
differences between the
manual and the product, the product has priority.
•This unit is designed for use with the following discs:
DVD-Video, DVD-Audio, DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD+R DL, Video CD,
Super Video CD, Super Audio CD (SA-CD), Audio CD,
CD-R and CD-RW.
t£
WJO§~
t£
WJO§~
VIDEO
CD
IDtGlTAl
VIlEOI
5!8 [SUPER
VIDEO)
~
WJe
WJDm
WJm
'Y7
SUPERAUDIO CD DIGITAL
lWDIO
1;1;«·",$1$1
IRewdta61el
•This unit can play:
-MP3, WMA (except copyright-protected WMA) and
picture (Kodak, lPEG) files recorded on CD-R(W)/
DVD-R(W)/DVD+R(W)
-lPEGIISO 9660 format
-Maximum
14
character display
-DivX® disc on CD-R(W)/DVD-R(W)/DVD+R(W)
-Official DivX® Certified product
-Plays all versions
of
DivX® video (including
DivX® 6) with standard playback
of
DivX® media
files
Not~
•CD-R(W), DVD-R(W) and DVD+R(W) cannot be played
unless finalized.
•Copyright-protected WMA files cannot be played with this
unit.
•This unit supports
lPEG
files
of
2848 x2136 pixels
in
size.
•Some discs cannot be played depending on the recording
conditions, such as the PC environment and application
software. The characteristics and condition
of
some discs;
materials, scratches, curvature, etc., may result
in
playback
failure.
•Be sure
to
use only CD-R(W), DVD-R(W) and DVD+R(W)
discs made
by
reliable manufacturers.
•Do not use any non-standard shaped discs (heart-shaped, etc.).
•Do not use discs with tape, seals, or paste on their surface.
Doing so may damage this unit.
•Do not use discs affixed with labels printed
by
acommercially
available label printer.
DVD region codes
This unit is designed to support the region management
system. Check the regional code number on the DVD disc
package. Ifthe number does not match the region code
of
this unit (see the table below or the back
of
this unit), this
unit may be unable to play the disc.
Destination Region code' Playable discs
of
this
unit
U.S.A.
~
(IJ (IJ
Canada
U.K.
~
~
~
Europe
Asia
~~
(IJ
Korea
Russia
~
~
(I)
3
En
INTRODUCTION
[](lIDOLBVI
DIGITAL
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks
of
Dolby Laboratories.
_db
Digital
Surround
"DTS" and "DTS Digital Surround" are registered
trademarks
of
DTS, Inc.
CI~
CERTIFIED
.'"
DivX, DivX Certified, and associated logos are
trademarks
of
DivX, Inc. and are used under license.
•When a disc becomes dirty, clean it with acleaning
cloth. Wipe the disc from the center out. Do not wipe in
acircular motion.
•Do not use solvents such as benzine, thinner,
commercially available cleaners,
or
antistatic spray
intended for analog records.
Check your package to make sure it contains the following
items:
IDCDrl
byFAROUDJA
"DCDi" is atrademark
of
Faroudja, adivision
of
Genesis
Microchip, Inc.
Hom.
"HDM!", the "HDMI" logo and "High Definition
Multimedia Interface" are trademarks or registered
trademark
of
HDMI Licensing LLC.
This product incorporates copyright protection
technology that is protected by method claims
of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use
of
this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized
by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
4En
Remote
control
DODO
eYAIIAIIA
Batteries (x2)
(AAA, R03, UM-4)
Audio pin cable
Video pin cable
Power cable
FUNCTIONAL
OVERVIEW
CD
Disc tray
Load adisc
in
the disc tray.
®STANDBY/ON
Turns on this unit
or
sets it to the standby mode.
®HDMI indicator
Lights up green when an HDMI component is
recognized by this unit and the HDMI mode is set to
on.
Lights up orange when no HDMI component is
recognized by this unit while the HDMI mode is set to
on.
®AUDIO DIRECT indicator
Lights up when you select the AUDIO DIRECT mode
by pressing AUDIO DIRECT on the remote control.
®Front panel display
Displays playback information
or
settings.
@L::J..
Opens or closes the disc tray.
(J)
1<J<]/<K1
Searches backward.*
Moves to the previous chapter
or
track.
®
[>(>Jt>[>I
Searches forward.*
Moves to the next chapter
or
track.
®
[>I1l0
Starts
or
pauses playback.
@D
Stops playback.
*Press and hold the button for about two seconds.
5En
FUNCTIONAL
OVERVIEW
CD
P.SCAN indicator
Lights up when the progressive scan function is
activated.
®Playback mode indicators
Display the icon for the selected playback mode.
®Decoder indicators
Display the icon for the selected internal decoder.
®MULTI indicator
Lights up when playing the multi-channel audio
source.
6En
®D.MIX indicator (DVD-Audio only)
Lights up when playing the disc that allows down
mixing
of
the multi-channel audio source.
®Disc indicators
Display the icon for the disc type.
(j) Information display
Displays various information such as atitle/chapter/
track number or elapsed playing time.
.:-'''-:.
You
can adjust the brightness
of
the front panel display using
DIMMER on the remote control.
(U.K., Europe, and Russia models)
FUNCTIONAL
OVERVIEW
CD
AUDIO OUT (6ch discrete) jacks
Connect to the 6ch input jacks
of
your
AV
receiver.
®DIGITAL (COAXIAL) jack
Connect to the coaxial inputjack
of
your
AV
receiver.
@REMOTE CONTROL (IN/OUT) connectors
Use in custom installations to transmit remote control
signals via cable connections.
®REMOTE CONTROL (RS-232C) terminal
(U.S.A., Canada, U.K., Europe, and Russia
models only)
Use as an expansion terminal for commercial use.
Consult your dealer for details.
®
AV
terminal
(U.K., Europe, and Russia models only)
Connect to SCART input terminal
of
your
TV.
®VIDEO OUT (VIDEO) jack
Connect to the composite video inputjack
of
your
AV
receiver.
rJ)
MAINS
Connect the supplied power cable.
®AUDIO OUT (MIXED 2CH) jacks
Connect to the audio inputjacks
of
your
AV
receiver or
stereo system.
®DIGITAL (OPTICAL) jack
Connect to the optical inputjack
of
your
AV
receiver.
@)
HDMI jack
Connect to the HDMI input jack
of
your HDMI
component.
@VIDEO OUT (S VIDEO) jack
Connect to the S-video inputjack
of
your
AV
receiver.
@VIDEO OUT (COMPONENT) jacks
Connect to the component input jacks
of
your
AV
receiver.
•Remote control connectors and RS-232C terminal
The REMOTE CONTROL (IN/OUT) connectors and the REMOTE CONTROL (RS-232C) terminal are used
in
custom installation. Keep the RS-232C switch set to OFF and do not connect any cables to these connectors during
normal use.
Caution: Do not touch the inner pins of the jacks on the rear panel of this unit. Electrostatic discharge
may cause permanent damage to this unit.
7En
FUNCTIONAL OVERVIEW
8En
CD
DIMMER
Selects from three different levels
of
brightness for the
front panel display: bright, dim and auto.
For auto setting, brightness
is
automatically set to low
only during playback.
®HDMI
Switches between the HOMI resolution settings or
turns off the HOMI mode (see page 36).
•
You
can select the HOMI resolution by pressing HOMI on
the remote control repeatedly
or
by
using the HOMI Video
setup menu.
•If you press HOMIon the remote control once, the
currently selected resolution setting
is
displayed in the top
left corner
of
the display and
in
the front panel display.
®GROUP
Selects the OVO-Audio group (see page 25).
@PAGE
(+/-)
Selects the OVO-Audio still picture (see page 24).
®Numeric buttons (0-9)
Select numbered items
in
the currently displayed
menu.
®CLEAR
Clear the mode or setting (see page 20).
(J)
SETUP
Accesses or exits from the setup menu
of
this unit
(see page 28).
®
STOP(_)
Stops playback (see page
18).
®PAUSE (
..
)
Pauses playback temporarily (see page
18).
Frame-by-frame playback (see page
18).
@)
SKIP
(~~
/~~I)
Moves to the previous/next chapter or track.
Qj)
TOP MENU
Displays the top-level disc menu.
The title menu
is
displayed for discs with the title menu.
@
Cursors(~/~/~/")
Selects an item
in
the currently displayed menu.
ENTER
Confirms the menu selection.
@MENU
Accesses the menu
of
adisc (see page 20).
®SUBTITLE
Selects the subtitle language (see page 24).
@AUDIO
Selects the audio language or format (see page 24).
@POWER
(I)
Turns on this unit (see page 15).
@STANDBY(<!»
Sets this unit to the standby mode (see page 15).
®AUDIO DIRECT
Turns off the video output during audio disc playback
in orderto improve audioquality. Press again to tum on
the video output. This function is not available when an
HDMI component is recognized by this unit.
In the AUDIO DIRECT mode, the front panel display
goes out. Once this unit is turned off, the AUDIO
DIRECT mode is cleared (only when an SA-CDdisc is
played back, the mode is cleared
if
the disc tray is
opened/closed).
@MULTI/2CH
Selects asound mode: Stereo
or
Multi-channel.
Changes the SA-CD playback area (see page 25).
@PROG
Accesses the program setup menu to program disc
tracks
or
exit from its menu (see page 20).
@RANDOM
Plays tracks in random order (see page
19).
@REPEAT
Repeats the chapter, track, title, group
or
disc
(see page 19).
FUNCTIONAL
OVERVIEW
@A-B
Repeats aspecific segment (see page
19).
@ENTER
Confirms the menu selection.
@)
SLOW/SEARCH
(~~
/~~)
Searches backward
or
forward (see page
19).
@PLAY
(~)
Starts playback (see page 18).
@ON SCREEN
Accesses
or
exit from the on-screen display (OSD)
menu
of
this unit (see page 21).
Press twice during playback to access the Picture
Setting menu (see page 22).
@RETURN
Returns to the previous setup menu.
@l
ZOOM
Enlarges the video image (see page 23).
@ANGLE
Selects the DVD camera angle (see page 23).
:<i<:.
Two ENTER buttons (@ and @) act
in
the same way.
9En
CONNECTIONS
Connecting an
AV
receiver with 6chl
multi-channel input
•
Analog
connections
If
you want to reproduce multi-channel Super Audio CD
(SA-CD) and DVD-Audio, connect AUDIO OUT (6ch
discrete)jacks
of
this unit to the corresponding input
jacks
of
your
AV
receiver using commercial1y available
audio pin cables.
~
cJ»-cJ»-cJ»-~
~
FRONT
CENTER
SUIWDOFER
SINIRDUND
<Ill
(!;l
<Ill
(!;l
Subwoofer
Stereo
amplifier
This unit has digital coaxial, digital optical, analog 6ch
discrete, and analog mixed 2ch outputjacks. Connection
depends on the availability
of
audio jacks on your
component.
This unit (U.K., Europe, and Russia models)
Connecting astereo amplifier
Connect AUDIO OUT (MIXED 2CH)jacks
of
this unit to
the corresponding input jacks
of
your audio component
(such as astereo amplifier) using the supplied audio pin
cable.
You
can connect asubwoofer to the
SUBWOOFER jack.
Be sure to
tum
offthis unit and unplug the power supply
cable, before you make
or
change connections.
•Depending on the component you want to connect, there
are various ways to make connections. Possible
connections are described below.
•Refer to the manuals supplied with your other
components as necessary to make the best connections.
•Do not connect this unit via your VCR. The video
quality could
be
distorted by the copy protection system.
•Do not connect the audio outjack
of
this unit to the
phono in
jack
of
your audio system.
Left
speaker Right
speaker
10
En
CONNECTIONS
AV
receiver <0>
AV
receiver
VIDEO
S
VIDEO
COMPONENT
OUT
OUT
VIDEO
OUT
This unit (U.K., Europe, and Russia models)
This unit has SCART, composite video, S-video, and
component video output jacks.
If
your
AV
receiver has
video outputjacks, connect your receiver and then your
TV so that you can use one TV for several different video
sources (LD, VCR, etc.)
by
simply switching the input
source selector on your receiver.
Use the one that corresponds to the inputjacks on the
component to be connected.
II
IT!TI
<A>
~
<B>
[1,~
-~
IN
IN
•Digital connections
If
you want to use the Dolby Digital, DTS,
or
MPEG
function on your
AV
receiver, connect DIGITAL
(OPTICAL) <A>
or
DIGITAL (COAXIAL) <B>
jack
of
this unit to the corresponding input jacks
of
your
AV
receiver using acommercially available digital optical
or
digital coaxial cable.
1/1iliii
•
If
you make aconnection with <A>
or
<8>,
set [Digital Out]
to [All] (see "Setting the digital output" on page 31).
•If the audio format
of
the digital output does not match the
capabilities
of
your receiver, the receiver produces adistorted
sound or no sound at all. Make sure to select the appropriate
audio format from the menu screen on the disc.
Pressing AUDIO on the remote control once
or
more may
change not only the audio languages but also the audio format.
•SA-CD audio signals are not output from DIGITAL
(COAXIAL/OPTICAL) jacks.
•If you want to enjoy Dolby Digital, DTS, and MPEG formats,
you must connect this unit to an
AV
receiver that supports
these formats.
TV
VIDEO
IN
S
VlOEO
COMPONENT
IN
VIDEO
IN
11
En
CONNECTIONS
•Composite video jack <A>
Connect VIDEO OUT (VIDEO)
jack
of
this unit to the
video input
jack
of
your
AV
receiver, and then to that
of
your
TV
using the supplied video pin cable.
•S-video jack <B>
S-video connections achieve aclearer picture than
composite video connections by transmitting video signals
on separate wires for luminance (Y) and chrominance (C).
Connect VIDEO OUT
($
VIDEO)
jack
of
this unit to
S-video input
jack
of
your
AV
receiver, and then to that
of
your
TV
using acommercially available S-video cable.
HDMI (High-Definition Multimedia Interface) provides
high quality digital audio and video on asingle
connection.
Connect the HDMI
jack
of
this unit to an HDMI inputjack
of
your
AV
receiver, and then to that
of
your TV using a
commercially available HDMI cable.
If
your receiver does not have an HDMI inputjack, you
can achieve abetter video image by connecting the HDMI
jack
of
this unit directly to the HDMI input
jack
of
your
TV.
~
I:~I
r
==:::7
AV
receiver
Speakers
TV
This
unit
(U.K., Europe, and
Russia models)
HOMIOUT
HOMIIN
iiliir'il
•.
M".,.,cc,W
•
You
need to make appropriate audio connections
if
the
connected component does not input audio signals (see
page 10).
•This unit
is
not compatible with HDCP-incompatible HDMI or
DVI components.
•
You
need acommercially available HDMIIDVI conversion
cable when you connect this unit to other DVI components. In
this case, you need to use another audio connection to this
connection because the HDMI jack
of
this unit does not output
any audio signals.
•Do not disconnect or turn offthe power
of
the HDMIIDVI
component connected to the HDMI jack
of
this unit while data
is
being transferred. Doing so may disrupt playback or cause
noise.
•Component video jacks
<C>
Component video connections achieve higher fidelity
color reproduction than S-video connections by
transmitting video signals on separate wires for luminance
(Y:
green) and chrominance
(Ps:
blue,
PR:
red). Connect
VIDEO OUT (COMPONENT)jacks
of
this unit to the
component inputjacks
of
your
AV
receiver, and then to
those
of
your
TV
using acommercially available
component cable. Observe the color
of
each
jack
when
you make connections.
If
your receiver does not have component outputjacks,
you can achieve abetter video image by connecting the
component output jacks
of
this unit directly to the
component input jacks
of
your
TV.
•Ensure that the "TV" indication on SCART cable is connected
to the TV set and "DVD" indication on SCART cable is
connected to this unit.
•S-video signal
is
not output at
AV
tenninal. See page 36 for
SCART video setting.
•SCART terminal
<0>
(U.K., Europe, and Russia models only)
If
your TV has only aterminal for video input, you can
connect the
TV
directly to this unit.
Connect
AV
terminal
of
this unit to SCART input terminal
of
your TV using acommercially available SCART cable.
,1,
~<iI~
When connecting an HDMI component, refer to the manual
supplied with your component.
12 En
CONNECTIONS
•HOMI video output
This unit is compatible with the following video fonnats:
480p/60 Hz,
S76p/SO
Hz,
nOp/50
Hz, 60 Hz, 1080i/SO Hz, 60 Hz, and
1080p/SO
Hz, 60 Hz.
NO,t,!$l
•
You
need to select one
of
the HDMI resolution settings by pressing HDMI on the remote control repeatedly or by using the HDMI
Video setup menu (see page 36).
•Depending on the connected DVI component, black and white
in
the image may not
be
distinct.
In
this case, adjust the picture setting
of
the connected DVI component.
•HOMI audio output
Audio format Analog output'
..
'
.'.
HDMIAudlo
setting AutO*l
PCM
Off
Multi-channel PCM multi*2
Dolby Digital Stereo Dolby Digital PCM 2ch
Multi-channel PCM multi*2
DTS DTS
DVD-Video Stereo PCM 2ch
Multi-channel PCM multi*2
MPEG MPEG
Stereo PCM 2ch
PCM 2ch*4 Multi-channeVStereo PCM 2ch PCM 2ch
Multi-channel PCM (PPCM) multi*2,3 PCM (PPCM) multi*2,3
Multi
DVD-Audio Stereo PCM (PPCM) 2ch*3 PCM (PPCM) 2ch*3
2ch*4 Multi-channeVStereo PCM (PPCM) 2ch PCM (PPCM) 2ch Ofr
CDIMP31 2ch Multi-channeVStereo PCM 2ch PCM 2ch
WMNDivX®
Multi-channel PCM multi*2
Multi
DTS-CD Stereo DTS PCM 2ch
2ch Multi-channeVStereo PCM 2ch
VCD 2ch Multi-channeVStereo PCM 2ch PCM 2ch
Multi-channel PCM multi*2
Multi
SVCD Stereo MPEG PCM 2ch
2ch Multi-channeVStereo PCM 2ch
SA-CD Multi/2ch Multi-channeVStereo - - -
*
I:
If
the connected HDMI component does not support bitstream signals (Dolby Digital, DTS, and MPEG), the audio
output is automatically changed from bitstream signals to PCM signals.
*2:
If
the HDMI component does not support multi-channel audio signals, the audio output is automatically changed
from PCM multi-channel signals to PCM stereo signals and 48 kHz!16 bits signals or less.
*3:
If
the audio source is prohibited from downmixing, the front
UR
channel audio and 48 kHz!16-bit signals
or
less are
output instead
of
downmixed stereo.
*4:
If
the connected component does not support more than 48 kHz, the audio output is automatically changed to 48 kHz!
16-bit signals
or
less.
Notejij
•
You
need to set HDMI Audio (see page 37).
•SA-CD signals cannot be output using HDMI. Make an analog connection
to
listen to SA-CD (see page 10),
13 En
CONNECTIONS
After all otherconnections are complete, plug the supplied
power cable into MAINS
of
this unit and then plug the
power cable to an AC outlet.
14
En
GETTING
STARTED
~\M-:.
If the settings you have made are inappropriate, you can always reset all options and your personal settings
to
the initial factory settings.
For details, see "Resetting the system" on page 30.
1Press
the.
part and slide the battery
compartment cover off.
2Insert the two supplied batteries (AAA, R03,
UM-4), following the indications
(+/-)
on
the
inside
of
the compartment.
3Slide the cover back until it snaps into place.
•Insert batteries correctly according to the polarity markings
(+/-).
The batteries inserted
in
the opposite direction may leak.
•Replace the exhausted batteries immediately with new ones to
prevent aleakage.
•Remove the batteries from the compartment ifthe remote
control
is
not used for more than amonth.
•If the batteries have leaked, dispose
of
them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
•Do not use old batteries together with new ones.
•Do not use different types
of
batteries (such
as
alkaline and
manganese batteries) together. Read the packaging carefully
as
these different types
of
batteries may have the same shape and
color.
•Dispose
of
the batteries correctly
in
accordance with your local
regulations.
Using the remote control
Use
the
remote control within 6 m (20
ft
approx.) ofthis
unit
and
point it
toward
the
remote control
sensor.
•Do not spill water or other liquids on the remote control.
•Do not drop the remote control.
•Do not leave
or
store the remote control
in
the following types
of
conditions:
-places
of
high humidity, such
as
near abath
-places
of
high temperature, such as near aheater or stove
-places
of
extremely low temperature
-dusty places
1Make sure that the power cable is connected to
an AC outlet.
2
Tum
on
your TV and
AV
receiver.
3Select the appropriate input source
of
the
AV
receiver connected to this unit. Refer to the
manual supplied with your
AV
receiver for
details.
4Press STANDBY/ON
on
the front panel
or
POWER (I ) on the remote control to
tum
on
this unit.
~
The front
panel
display lights
up.
5Set the
TV
to the correct Video IN channel (e.g.,
EXTl/2,
AV1I2, AUDIOIVIDEO, etc. Refer to
the manual supplied with your
TV
for details).
~
The default screen appears
on
the
TV.
15 En
GETTING STARTED
This unit is compatible with both NTSC and PAL video
formats. Select the color system that matches your
TV.
,I,
~<il:'
•Press RETURN to display the previous menu.
Press SETUP to exit from the setup menu.
1
Press
SETUP.
~
The setup menu appears.
2Press..Ao...l
~
repeatedly
to
select
[VIDEO],
and
then
press
ENTER.
~
[VIDEO]
menu
appears.
*1: [Black Level] and [Closed Caption] are only for U.S.A. and
Canada models.
*2: [Scart Video Out] is only for u.K., Europe, and Russia
models.
16
En
3
Press
..Ao...1
.......
repeatedly
to
highlight
[TV
Type].
4
Press
....
1
~
to
select
one
of
the
options
below.
PAL
Select this
if
the connected TV
is
aPAL system
TV.
It
will
change video signals
of
NTSC discs and output them
in
PAL format.
NTSC
Select this if the connected TV is an NTSC system
TV.
It
wil1
change video signals
of
PAL discs and output them
in
NTSC format.
MULTI
Select this
if
the connected
TV
is compatible with both
NTSC and PAL formats (such as amulti-system TV). The
output format will be in accordance with the video signals
of
the disc.
•Before changing the current TV Standard setting, ensure that
your TV supports the selected TV type system.
•Ifyou play an NTSC-formatted disc with the [PAL] setting or a
PAL-formatted disc with the [NTSC] setting, the video quality
may deteriorate.
•When [TV Type]
is
set to [MULTI], this unit may change the
HDMI resolution unwantedly. In this case, try the [NTSC] or
[PAL] setting.
Other manuals for DVD-S1800
2
Table of contents
Other Yamaha DVD Player manuals
Yamaha
Yamaha SV-S5860 User manual
Yamaha
Yamaha DVD-S659BL User manual
Yamaha
Yamaha DV-C6280 User manual
Yamaha
Yamaha DVD-S2300 User manual
Yamaha
Yamaha CinemaStation DVD-S30 User manual
Yamaha
Yamaha DVD-C940 User manual
Yamaha
Yamaha DV-S5350 User manual
Yamaha
Yamaha DVD-S1800 User manual
Yamaha
Yamaha DVD-S530 User manual
Yamaha
Yamaha CinemaStation DVD-S30 User manual
Yamaha
Yamaha DVD-S2700 User manual
Yamaha
Yamaha DV-S6165 User manual
Yamaha
Yamaha DVD-S520 User manual
Yamaha
Yamaha DVD-S657 User manual
Yamaha
Yamaha DVD-S796 User manual
Yamaha
Yamaha DVD-S557 User manual
Yamaha
Yamaha DVD-S661 User manual
Yamaha
Yamaha DVD-S663 User manual
Yamaha
Yamaha DVD-S657 User manual
Yamaha
Yamaha DVD-S659 User manual
