Yamaha LS9-32 User manual

!
1
YAMAHA LS9-32
QUICK START GUIDE
FIRST EDITION
ENGLISH

TURNING ON THE SYSTEM
We can’t make sound until everything has power. Below are step by step instructions from
when you walk in to when you leave. It’s important to not only turn the system on correctly
but to also make sure EVERYTHING is turned offbefore you leave. Therefore please follow
these instructions carefully to ensure minimum damage to the system during power up and
down.
2

Step 1:!
You will need to go to the Main Power Switch room to turn on the circuit breaker for H38.
Use the map above to help guide you to the room. Once there, you will need to turn on the
“General Neon” and “Lights Scene” switches from 0 to I. DO NOT touch any other power
switch.
Step 2:!
Make your way back into the main room, over to the sound desk. Turn on both power
boards so they light up. Once that is done, turn on the LS9-32 with the switch on the back,
the wireless microphone receivers and antenna which are located under the desk.
3

Step 3:!
Then at the front of the stage on the left hand side, there will be another power board, turn
this on. Then under the stage turn on all the FOH (Front of House) amps. Finally turn on
the A-16D Pro.
TURNING OFF THE SYSTEM
Once you have finished the service or rehearsal it’s important to turn offthe system safely.
The process is the reverse of turning the system on, but here are detailed steps to help.
IMPORTANT: Power boards should always be turned offlast on each step.
Step 1:!
Turn offall FOH amps and the A-16D Pro. After they are all turned offyou may switch off
the power board.
Step 2:!
Turn offthe LS9 Desk and the wireless’ receivers and antenna. After they are all turned off
you may switch offthe power board.
Step 3:!
Switch offthe “General Neon” and “Lights Scene” circuit breakers."
4

LS9’S SCENE FUNCTION
Now that everything has power and is turned on, let’s set up the LS9 for use. To do this,
first we need to ‘recall’ the appropriate Scene. A Scene is a saved file for all the parameters
of the LS9, it saves everything from the I/O to fader positions. If you would like to know
more detail about Scenes and how they work, please contact Pascal Hausamman or Ryan
Jones.
To Recall (load a saved scene) a scene from the LS9 for use, select the Scene Memory button
on the Display Access section of the desk. This will open a menu on the LCD screen where
you can operate the Scene Functions. This screen will have tabs just under the top left
corner of the LCD Screen. We need the Scene List tab, to get there press the Scene Memory
button until you have arrived on the Scene List tab. You should see a scene table like the one
below.
To select your desired scene use the large Scroll Wheel over in Data Entry Section on the
right side to highlight the scene. Once selected, move the cursor down to the bottom using
the Arrow buttons just above the large Scroll Wheel to the Recall function. Use the Enter
button use the function. A dialogue box will appear asking you for your confirmation. Select
OK using the Arrow buttons and confirm with Enter.
5

The scene is now available for use. Only Admins are allowed to save Scenes, if you need
admin access please contact the admin for your team’s Master Scene:
Pascal Hausamman H38 Rept (Sunday Rehearsal) [phone]!
Ryan Jones Young Adults (YA) [phone]!
William Aronsson Youth [phone]
If there is no need to save the Scene, nothing is required once you have finished, the LS9
desk can be switched offsafely while a scene is loaded following the instructions for
Powering Down the System on page 4.
CONNECTING AN IPAD
The use of an iPad is very useful for mixing as it allows the user to move away from the LS9
desk while still having full control. A network has been set up so any iPad with the LS9
StageMix app can connect. You can find the LS9 StageMix app by searching the App Store on
the iPad, please install the app first before moving on.
Once you have installed the LS9 StageMix app you will need to connect to the network that
the LS9 is connected to. Open the wifi settings on the iPad and connect to the H38 Yamaha
LS9 network. The password required is: happysky311!
Please note this network has no internet, you can not download the app on this network.
Once wifi is connected, open the StageMix app and press on Add Mixer. Here is the
information you will need:
Once all the information is filled out, press Add Mixer. This will take you back to the main
page of the app with the mixer you just added in the list. Select the mixer and press
Connect. It may take a few seconds for the app to sync to the desk, when finished you now
have complete control over the desk.
6