Yamaha EV-204 User manual

SERVICE MANUAL
HAMAMATSU, JAPAN
0.944K-019 Printed in Japan 2002.05
011636
NV
CONTENTS
SPECIFICATIONS .............................................................................. 3
PANEL LAYOUT.................................................................................. 4
CIRCUIT BOARD LAYOUT................................................................. 6
BLOCK DIAGRAM .............................................................................. 7
DISASSEMBLY PROCEDURE ........................................................... 8
IC BLOCK DIAGRAM........................................................................ 12
CIRCUIT BOARDS ........................................................................... 12
INSPECTIONS.................................................................................. 13
.......................................................................................................... 14
TUNING ............................................................................................ 15
OVERALL CIRCUIT DIAGRAM
PARTS LIST
This document is printed on chlorine free (ECF) paper with soy ink.
EV-204 / EV205
EV-204: 20020420-129000
EV-205: 20020420-145000
ELECTRIC VIOLIN
EV-205CBEV-204AM

2
EV-204 / EV-205
WARNING
Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical / electronic and / or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and WelfareAgency (and possibly other
entities) to cause cancer and / or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL / ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY
REASON WHAT SO EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to
solder / flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed
that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under-
stood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in
personal injury, destruction of expensive components and failure of the product to perform as speci-
fied. For these reasons, we advise all Yamaha product owners that all service required should be
performed by an authorized Yamaha Retailer or the appointed service representative.
IMPORTANT:
This presentation or sale of this manual to any individual or firm does not constitute authorization, certifica-
tion, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any
form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research engineering,
and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevi-
table and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy
appear to exist, please contact the distributor's Service Division.
WARNING:
Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus).
IMPORTANT: Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power
to the unit.

3
EV-204 / EV-205
SPECIFICATIONS
Neck Hard Maple
Fingerboard/Nut Ebony
Bridge Single Unit with Pickup
Body Frame Maple
Sound Board Maple
Chin Rest Ebony
Tailpiece EV-204 : Ebony (4 hole type)
EV-205 : Ebony (5 hole type)
Tuning Pegs Gear Type
Strings EV-204 : YAMAHA strings (EV4S)
EV-205 : YAMAHA strings (EV5S)
Pickup Individual high power output pickup for each string
Connectors/Controls • MODE Select Switch
(CONTROLLED (Active)/DIRECT (Passive))
• MASTER VOLUME
• LINE OUT
(with the power “ON” and a cable connected)
• OUTPUT IMPEDANCE: LINE OUT 0~500kΩ
• Pickup Level Controls (Available to ‘CONTROLLED’ mode)
EV-204 : 4ch Mixer & Main Volume
EV-205 : 5ch Mixer & Main Volume
• PHONES (POWER ON when a plug is inserted.)
• PHONES VOLUME
Power Supply 6F22 (S-006P) 9V battery x1
Battery Life Used with headphones
(MODE=CONTROLLED, Continuous Use)Manganese battery: approximately 6.5 hours
Alkaline battery: approximately 15 hours
Used without headphones
Manganese battery: approximately 8 hours
Alkaline battery: approximately 18 hours
String Length 328 mm (12-15/16”)
Dimensions EV-204 : 589 (L) x 206 (W) x 126 (H) mm
23-3/16” (L) x 8-1/8” (W) x 4-15/16” (H)
EV-205 : 601 (L) x 206 (W) x 132 (H) mm
23-11/16” (L) x 8-1/8” (W) x 5-3/16” (H)
Weight (with battery) EV-204: 700g (1 lbs. 8 oz.)
EV-205: 717g (1 lbs. 9 oz.)
Color AMBER, PEARL RED, COSMIC BLUE

4
EV-204 / EV-205
PANEL LAYOUT
FRONT
Tuning peg
Nut
Neck
Fingerboard
4th string (G)
2nd string (A)
3rd string (D)
1st string (E)
Body Frame
Bridge
Master Volume
Tailpiece
Chin rest
End pin
Tailpiece Wire
5thstring (C):EV205 Oniy
Sound Board
The EV-205 is the illustration.

5
EV-204 / EV-205
CONTROL PANEL side
qMode Select Switch [CONTROLLED / DIRECT]
wPickup Level Control 1-5 (located inside)
ePickup Level Control MAIN (located inside)
rPHONES VOLUME
tPHONES jack: Stereo mini type
yLINE OUT jack: Standard phone type
uBattery: 6F22(S-006P) 9V
iBattery Case Cover: 6F22(S-006P) 9V
oMASTER VOLUME
u
CONTROLLED DIRECT
VOLUME PHONES LINE OUT
MAIN
5
4321
OPEN
ty
q
we
i
o
r

6
EV-204 / EV-205
CIRCUIT BOARD LAYOUT
AMP
Bridge Assembly

7
EV-204 / EV-205
BLOCK DIAGRAM
MASTER
VOLUME
J1-6P
J3-3P J2-2P Battery:C
JK2: PHONE
JK1: LINE OUT
SW1
SW2
1
2
3
4
5
6
1
2
3
21
3
54
6
11 12
10
87
9
21
3
87
9
56
4
12
10
11
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc Vcc Vcc
R1
R2
R3
R4
R11
U1A
U1B
U2A
U2B
VR
U3A
U3B
U4A
R26
U4B U5B
D1
U5A
R25
38
4
1
2
56
7
8
4
38
4
1
2
56
7
8
4
38
4
1
2
38
4
1
2
57
8
4
6
57
8
4
8
4
6
38
4
16
5
4
3
2
7
8
9
1
6
5
4
3
2
7
8
9
1
2
Vcc
57
6
AMP
PICKUP
ASSEMBLY
CONTROLLED /
DIRECT
Vcc
Vcc/2 Vcc/2
Vcc/2
Vcc/2
Vcc/2
Vcc/2
Vcc/2
Vcc/2
Vcc/2
Vcc/2
Vcc/2
Vcc/2
BUFFER x 5
LPF
2
3
4
5
MAIN
VOLUME
1

8
EV-204 / EV-205
DISASSEMBLY PROCEDURE
PREPARATION
Before disassembling the unit, confirm the following
items.
• Remove the chin rest.
• Remove the battery from the battery box. (Fig.1)
• Loosen all the strings and remove them. (Fig.2)
[130]
[140]
AMP
Bridge Assembly
Bridge Connector
Master Volume Connector
1. Amplifier Unit (Time required: about 1 min)
1-1 Open the battery cover, and remove the screw
marked [140]. (Fig.3)
1-2 Remove the three (3) screws marked [130].
The amplifier unit can then be removed. (Fig.3)
1-3 Remove the bridge connector and the master
volume connector from the AMP circuit board.
(Fig.3)
(Fig. 1) (Fig. 2)
(Fig. 3)
[130]: Oval Head Screw 3.0X25 MFZN2BL (V8829900)
[140]: Oval Head Screw 3.0X16 MFZN2BL (V8830000)

9
EV-204 / EV-205
[60]
[30]
[110]
AMP
Shield sheet
(Aluminium evaporated side)
GND tape
Fold back and apply to ground pattern on the
component side of the AMP circuit board.
2. AMP Circuit Board (Time required: about 3 min)
2-1 Remove the amplifier unit. (See procedure 1)
2-2 Remove the four (4) screws marked [60]. (Fig.4)
2-3 Remove the hexagonal nut marked [110]. (Fig.4)
2-4 Remove the VR knob marked [30].
The AMP circuit board can then be removed.
(Fig.4)
Note: • When reinstall the AMP circuit board, bundle
the shield sheet (GND tape attached) by the
same screw as shown in the illustration.
(Fig.4)
• When reinstall the slide button marked [C20]
and the slider marked [C100], set the two
slide switches on the AMP circuit board to
the same direction. (Fig.5)
[C20]
[C100]
AMP
Slide SW knob
Slide SW knob
Slide SW knob
(Fig. 4)
(Fig. 5)
[30]: Knob ABS (VP224600)
[60]: PWHP Tapping Screw 3.0X8-8 MFZN2Y (VA122000)
[110]: Hexagonal Nut 12.0 MFZN2BL (VB508600)
Apply the GND tape to alu-
minium evaporated side of the
shield sheet, and fold it back to
apply to ground pattern on the
component side of the AMP
circuit board

10
EV-204 / EV-205
3.
Tailpiece Assembly (Time required: about 4 min)
3-1 Remove the amplifier unit. (See procedure 1)
3-2 Remove the connector assembly from the AMP
circuit board.
The tailpiece assembly can then be removed.
(Fig.6)
4. Volume Assembly (Time required: about 5 min)
4-1 Remove the tailpiece assembly. (See procedure 3)
4-2 Remove the screw marked [50]. (Fig.6)
4-3 Remove the VR knob marked [30].
The volume assembly can then be removed. (Fig.6)
[30]
[50]
Tailpiece Assembly
Damper
Bridge Assembly
Body
[80]
PushPush PickupPickup
5. Bridge Assembly (Time required: about 4 min)
5-1 Remove the amplifier unit. (See procedure 1)
(Remove the connector assembly from the AMP
circuit board.)
5-2 Remove the bushing marked [80].
The bridge assembly can then be removed. (Fig.7)
(Fig. 6)
(Fig. 7)
[30]: Knob ABS (VP224600)
[50]: Bind Head Tapping Screw 2.6X5 MFZN2BL (EP620150)

11
EV-204 / EV-205
[60]
[70]
[20]
6. Sound Plate Assembly
(Time required: about 5 min)
6-1 Remove the tailpiece assembly. (See procedure 3)
6-2 Remove the bridge assembly. (See procedure 5)
6-3 Remove the screw marked [60] and the screw
marked [70].
The sound plate assembly can then be removed.
(Fig.8)
Note: When remove the sound plate assembly, take
care not to lose the two spacers. (Fig.8)
(Fig. 8)
[20]: Speacer (V8768400)
[60]: Bind Head Screw 4.0X30 MFZN2BL (VT229100)
[70]: Bind Head Screw 4.0X20 MFZN2BL (VB403600)

12
EV-204 / EV-205
Note: See parts list for details of circuit board component parts.
AMP: V877000
CIRCUIT BOARDS
•AMP Circuit Board
Component Side
IC BLOCK DIAGRAM
AMP: U1, U2, U3, U4
NJM4556V (X2473A00)
Dual Operational Amplifier
1
2
3
4
8
7
6
5
Output A
Non-Inverting
Input A
-DC Voltage
Supply
(GND)
+DC Voltage
Supply
Output B
Inverting
Input B
Non-Inverting
Input B
Inverting
Input A
+-
+-
A
B
NJM4580AV (X2474A00)
Dual Operational Amplifier
1
2
3
4
8
7
6
5
Output A
Non-Inverting
Input A
-DC Voltage
Supply
(GND)
+DC Voltage
Supply
Output B
Inverting
Input B
Non-Inverting
Input B
Inverting
Input A
+-
+-
A
B
VOLUME PHONES LINE OUT
to MASTER VOLUME
to Pickup Assembly
Pattern Side
AMP: U5

13
EV-204 / EV-205
INSPECTION
1. Preparation
To check the unit, following jigs are required.
• Headphones
• Guitar Amplifier
• Battery (6F22Y or 6LR61)
Set each control as follows.
• Master Volume: Maximum
• [VOLUME] knob: Center
• MODE select switch: DIRECT
• Pickup Level Controls: See P.5 CONTROL PANEL Side , .
2. Inspection Procedure
2-1 Connect a guitar amplifier to {LINE OUT] jack.
2-2 Touch strings with a finger, and confirm that the hum noise decreases.
2-3 Play strings with a finger, and confirm the following items.
• Each string sounds normally.
• The fluttering noise is not produced.
• Each string has almost the same sound volume.
2-4 Confirm that the sound becomes larger according as turning the MASTER VOLUME knob to right, and that the
sound becomes smaller according as turning to left.
After finishing this test, set the MASTER VOLUME knob to maximum.
2-5 Set the MODE select switch to 'CONTROLLED'.
2-6 Play strings with a finger, and confirm that each string has almost the same sound volume.
2-7 Connect headphones to [PHONES] jack.
2-8 Play strings with a finger, and confirm that the sound level from headphones is large enough.
2-9 Play strings with a bow, listen to sound from the guitar amplifier, and confirm the following items.
• The sound has a normal volume and tone.
• The fluttering noise or mechanical noise are not produced.
To finish the inspection, set each control as follows.
• MASTER VOLUME: Maximum
• [VOLUME] knob: Minimum
• MODE select switch: DIRECT
POINTS TO CHECK WHEN NOISE HAS OCCURED
When a flattering noise or mechanical noise is produced, adjust the
tailpiece wire as follows.
Pull the tailpiece wire with a screw driver which is 7mm in
diameter so that the length of the tailpiece wire measures up to
about 38mm as shown in the illustration. (Fig.1)
Then confirm that the volume assembly is settled in the hole of the
sound plate and it dose not touch the sound plate.
If the above conditions are not met, fine adjust the length of
tailpiece wire.
About 38mm
(Fig. 1)
7mm Driver

14
EV-204 / EV-205

15
EV-204 / EV-205
TUNING
First, set up the bridge and then proceed with tuning.
•The lower side of the bridge supports the 1st string (E), the higher side supports the 4th
string (G) [EV205: the 5th string (C)]. Make sure the bridge is placed properly. (Make
sure the flat side of the bridge is facing the tailpiece, and rounded side is facing the
finger board.)
Looking from the tailpiece
Correct
Bad
Bridge is placed vertically
Tailpiece
Tuning
•The strings are tuned to the following pitches. The 1st string is tuned to E, the 2nd string
to A, the 3rd string to D, the 4th string to G and the 5th string to C (EV-205).
Use a piano, tuning fork, tuner, etc. and adjust the pitch of each string using the pegs.
•After tuning is complete, make sure that the tailpiece side of the bridge is still properly
aligned. If the bridge is leaning in either direction, slightly loosen the strings and care-
fully re-align the bridge using both hands.
Bad
Right angle
Body
E
A
D
G
[EV-204]
E
A
D
G
[EV-205]
C
[EV-204] [EV-205]
1st string (E)
2nd string (A)
4th string (G)
3rd string (D)
5th string (C)
4th string (G)
3rd string (D)
1st string (E)
2nd string (A)
4th string 1st string
5th string 1st string
Slit
Slit
Rounded side
Flat side
•Ensure that the tailpiece side of the bridge stands vertically. If it leans to one side, use
both hands to adjust. Make sure that each string passes over the corresponding slits in
the bridge.
* Playing the violin with a leaning bridge may result in damage to the bridge
or a deterioration in sound quality.

EV-204 / EV205
EV204 / EV205
EV204 / EV205
ABCDEFGH
1
2
3
4
5
EV204 / EV205 OVERALL CIRCUIT DIAGRAM (AMP)
Note: See parts list for details of circuit board component parts.
<P.1>
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP
AMP
to Pickup Assembly
KEC-54278
8
3
21
84
13
2
5
67
84
3
21
84
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13 FG
14
FG
5
67
84
13
2
1 3
2
13
2
13
2
13
2
3
21
4
1
2
3
4
5
6
7
8
9
10
11
12
13 FG
14
FG
3
21
84
GND
1
L
2B1
4
T1
5
M1
6
R
3
B2
7
T2
8
M2
9
5
67
84
1
1
2
2
33
3
21
84
1
2
1 3
2
5
67
84
GND
1
R
3
B1
4
T1
5
M1
6
L
2
B2
7
T2
8
M2
9
5
67
84
9Vdc
+
-
V1
C14
10/16
+
C15
0.022u
U1A
NJM4580
+
-
R25
RK09L1140(5kA)
U1B
NJM4580
+
-
U2A
NJM4580
+
-
R22
1.2k
J1
CON6
SW2
SSSF040800
R15
100
U2B
NJM4580
+
-
R2
RK08H1130(500kA)
R3
RK08H1130(500kA)
C1
10/16
+
R14
1M
R21
1M
R4
RK08H1130(500kA)
R11
RK08H1130(500kA)
R1
RK08H1130(500kA)
U3A
NJM4580
+
-
R24
100k
R18
1M
C20
10/16
+
C23
47/16
+
R23
10k
C2
1/50
+
C12
1/50
+
C3
1/50
+
C27
1/50
+
R31
22k
SW1
SSSF040800
C17
2200p
C6
2200p
R29
10k
U5A
NJM4556A
+
-
JK1
YKB21-5008
R32
33
C11
0.1u
C7
2200p
U4B
NJM4580
+
-
C8
2200p
C21
1/50
+
C9
2200p
J3
CON3
R16
1M
U4A
NJM4580
+
-
D1
RB160L-40TE25
C16
2200p
C10
10/16
+
J2
CON2
R19
2.2k
C24
10/16
+
R26
RK08H1130(10kB)
C4
1/50
+
R33
100k
C19
100p
U5B
NJM4556A
+
-
R5
2.2k
R13
1M
C25
2200p
R6
2.2k
R17
1M
R30
1k
R7
2.2k
R9
10k
C22
1/50
+
C18
1/50
+
R8
2.2k
R10
10k
JK2
LGS6507-0800
R28
4.3k
R27
100k
R20
1M
U3B
NJM4580
+
-
C5
1/50
+
C13
10/16
+
VCC
VCC
VCC
VCC
VCC
VCCVCC VCC
VCC
VCC
VCC
VCC
VCC/2
Master Volume
Battery
500kA
LINE OUT
PHONES

EV204 / EV205
1
PARTS LIST
WARNING
Components having special characteristics are marked and must be replaced with parts having
specifications equal to those originally installed.
CONTENTS
OVERALLASSEMBLY...................................................................................................... 2
ELECTRICAL PARTS ....................................................................................................... 5
• The numbers in “ QTY ” show quantities for each unit.
• The parts with “ - - ” in “ PART NO. ” are not available as spare parts.
• The mark “ } ” in the remarks column indicates that these parts are interchangeable.
• The second letter of the shaded ( ) part number is O, not zero.
• The second letter of the shaded ( ) part number is I, not one.
Note) DESTINATION ABBREVIATIONS
A: Australian model M: South African model
B: British model O: Chinese model
C: Canadian model Q: South-east Asia model
D: German model T: Taiwan model
E: European model U: U.S.A. model
F: French model V: General export model (110V)
H: North European model W: General export model (220V)
I: Indonesian model N,X: General export model
J: Japanese model Y: Export model
EV-204 / EV205
ELECTRIC VIOLIN

EV204 / EV205
2
OVERALL ASSEMBLY
A10
A100
A60
A50
A50
A30
A30
A20
A90
A20
D10a
D10b
D10c
10
EV204
90
190
80
150
160
100 110 130
140
180
170
120
3040506070
20
C10
C40
C70
C90
C30
C20
C100
C120
C110
C60
C80
C50
A70
A40
A80
EV204
EV204
D60
D10
D50
D30
D60a
D60b
D10d

EV204 / EV205
3
REF NO.PART NO. DESCRIPTION REMARKS QTY RANK
RANK : Japan onl* : New parts
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
10
10
10
10
10
10
20
20
30
40
50
60
70
80
90
100
110
120
120
130
140
150
150
160
170
180
190
A10
A10
A10
A10
A10
A10
A20
A30
A30
A40
A50
A50
A60
A70
A80
A90
A90
A90
A100
A100
--
--
--
--
--
--
--
--
--
--
--
--
V8757700
V9045400
V8757800
V8757900
V8758000
V8758100
V8758200
V8758400
V8767300
V9460800
--
--
--
V8829900
V8830000
--
--
22764900
V9460700
V9460500
V9281600
--
--
--
--
--
--
--
V8760400
V9043700
V9043800
V9045100
V9045200
V9045300
V8768400
V8769000
V8778200
V8761200
V8832100
V8832100
VT229100
VB403600
V8830800
V8760500
V9043900
V9044000
--
--
OVERALLASSEMBLY
Overall Assembly
Overall Assembly
Overall Assembly
Overall Assembly
Overall Assembly
Overall Assembly
Body Assembly
Body Assembly
Body Assembly
Body Assembly
Body Assembly
Body Assembly
Bridge Assembly
Bridge Assembly
String, E
String, A
String, D
String, G
String, C
Bushing
Battery Cover
Chin Rest
Amplifier Unit
Tailpiece Assembly
Tailpiece Assembly
Oval Head Screw
Oval Head Screw
Name Plate
Name Plate
Adhesive Tape
Spacer
Wood Screw
Cushion
ACCESSORIES
Battery
Body Assembly
Body Assembly
Body Assembly
Body Assembly
Body Assembly
Body Assembly
Wooden Unit Assembly
Wooden Unit Assembly
Wooden Unit Assembly
Wooden Unit Assembly
Wooden Unit Assembly
Wooden Unit Assembly
Spacer
Peg Unit
Peg Unit
End Pin
Round Head Wood Screw
Round Head Wood Screw
Bind Head Screw
Bind Head Screw
Oval Head Wood Screw
Sound Plate Assembly
Sound Plate Assembly
Sound Plate Assembly
Nut
Nut
AM
CB
PR
AM
CB
PR
AM
CB
PR
AM
CB
PR
E RE
A BL
D SL
G GR
C BR
3.0X25 MFZN2BL
3.0X16 MFZN2BL
12X50m
C-309
2.7X16 MFZN2BL
30X25
6F22Y(NR)
AM
CB
PR
AM
CB
PR
AM
CB
PR
AM
CB
PR
1st L14.5
2nd L13.5
3rd, 4th R13.5
5th R14.5
1st L14.5
2ndL13.5
3rd R13.5
4th R14.5
2.1X6.3 MFNI33
2.1X6.3 MFNI33
4.0X30 MFZN2BL
4.0X20 MFZN2BL
3.5X25 MFZN2BL
AM
CB
PR
EV-204/EV-205
EV-205 AM (V876660)
EV-205 CB (V904410)
EV-205 PR (V904420)
EV-204 AM (V904450)
EV-204 CB (V904460)
EV-204 PR (V904470)
EV-205 AM (V876030)
EV-205 CB (V904340)
EV-205 PR (V904350)
EV-204 AM (V904480)
EV-204 CB (V904490)
EV-204 PR (V904500)
EV-205
EV-204
EV-205
(V876720)
EV-205 (V875830)
EV-204 (V904550)
EV-205 (V924230)
EV-204 (V924240)
(PC10008)
EV205 AM (V876030)
EV205 CB (V904340)
EV205 PR (V904350)
EV204 AM (V904480)
EV204 CB (V904490)
EV204 PR (V904500)
EV205 AM
EV205 CB
EV205 PR
EV204 AM
EV204 CB
EV204 PR
EV205
EV204
EV204
EV205
EV204 AM, EV205 AM
EV204 CB, EV205 CB
EV204 PR, EV205 PR
EV205 (V930110)
EV204 (V930120)
3
2
8
10 01
01

EV204 / EV205
4
REF NO.PART NO. DESCRIPTION REMARKS QTY RANK
RANK : Japan onl* : New parts
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
C10
C20
C30
C40
C50
C60
C70
C80
C90
C100
C110
C120
D10
D10
D10a
D10a
D10b
D10b
D10c
D10d
D30
D50
D60
D60a
D60b
--
V8767400
V8767500
VP224600
V8767600
V8758500
VA122000
V8830600
V8769200
V8770000
V8896400
VB508600
V9064000
--
--
AAX34640
AAX34650
--
--
--
--
--
V9411500
VP224600
EP620150
V8769700
--
--
Amplifier Unit
Amplifier Case
Slide Button
Knob
Balance Knob
Shield Sheet
PWH Tapping Screw-P
Precision Screw
Wiring Assembly
Circuit Board
Slider
Hexagonal Nut
GND Tape
Tailpiece Assembly
Tailpiece Assembly
Tailpiece Sub Assembly
Tailpiece Sub Assembly
Tailpiece
Tailpiece
GND Sheet
GND Sheet
Tailpiece wire
Damper
Knob
Bind Head Tapping Screw-P
Volume Assembly
Rotary Variable Resistor
Volume Holder
ABS
3.0X8-8 MFZN2Y
1.4X3 MFZN2BL
BATTERY
AMP
BL
12.0 14X2 MFZN2BL
V-30 V-60
15X15X0.5
ABS
2.6X5 MFZN2BL
(V876720)
CONTROLLED-DIRECT
VOLUME
1,2,3,4,5,MAIN
EV205 (V875830)
EV204 (V904550)
EV204
EV205
EV205 (V876010)
EV204 (V877770)
EV205 (V876770)
EV204 (V877780)
EV204 (V547270)
MASTER VOLUME
MASTER VOLUME (V877630)
(V876960)
6
4
6
2
04
01
04
01