Yamaha RX-N600 User manual

SERVICE MANUAL
101007
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
■CONTENTS
TO SERVICE PERSONNEL ...................................... 2–3
FRONT PANELS ........................................................ 3–4
REAR PANELS .......................................................... 5–8
REMOTE CONTROL PANELS ...................................... 9
SPECIFICATIONS /参考仕様 ................................ 10–12
INTERNAL VIEW ......................................................... 13
DISASSEMBLY PROCEDURES /分解手順 ......... 14–20
UPDATING FIRMWARE /
ファームウェアの書き込み .................................. 21–24
SELF DIAGNOSIS FUNCTION (DIAG)/
自己診断機能（ダイアグ）...................................... 25–50
AMP ADJUSTMENT /アンプ部調整 ........................... 51
DISPLAY DATA ..................................................... 52–55
IC DATA ................................................................. 56–69
PIN CONNECTION DIAGRAMS ............................ 70–71
BLOCK DIAGRAMS .............................................. 72–75
PRINTED CIRCUIT BOARDS................................ 76–95
SCHEMATIC DIAGRAMS .................................... 97–108
REPLACEMENT PARTS LIST .......................... 109–138
REMOTE CONTROL.................................................. 139
ADVANCED SETUP .......................................... 140–141
P.O.Box 1, Hamamatsu, Japan
AV RECEIVER/AV AMPLIFIER
2006 All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
RX-N600/RX-N600D/HTR-N5060
DSP-N600
'06.06

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
2
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
WALL
OUTLET
EQUIPMENT
UNDER TEST
AC LEAKAGE
TESTER OR
EQUIVALENT
INSULATING
TABLE
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and
possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
■TO SERVICE PERSONNEL
1. Critical Components Information
Components having special characteristics are marked s
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
●Meter impedance should be equivalent to 1500 ohms
shunted by 0.15µF.
●Leakage current must not exceed 0.5mA.
●Be sure to test for leakage with the AC plug in both polarities.
“CAUTION”
“F3000, 3001: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE
8A, 125V FUSE.”
CAUTION
F3000, 3001: REPLACE WITH SAME TYPE 8A, 125V FUSE.
ATTENTION
F3000, 3001: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 8A, 125V.
本機に搭載されているすべての基板は無鉛ハンダでハンダ付けさ
れています。
無鉛ハンダにはいくつかの種類がありますが、修理時には下記の
ような無鉛ハンダの使用を推奨します。
・Sn+Ag+Cu（錫+銀+銅）
・Sn+Cu（錫+銅）
・Sn+Zn+Bi（錫+亜鉛+ビスマス）
注意：
無鉛ハンダの融点温度は通常の鉛入りハンダに比べ30〜40℃
程度高くなっていますので、それぞれのハンダに合ったハンダ
ごてをご使用ください。
All of the P.C.B.s installed in this unit are soldered using
the lead free solder.
Among some types of lead free solder currently available,
it is recommended to use one of the following types for the
repair work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
As the melting point temperature of the lead free solder is
about 30°C to 40°C (50°F to 70°F) higher than that of the lead
solder, be sure to use a soldering iron suitable to each solder.
About Lead Free Solder / 無鉛ハンダについて

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
3
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
■FRONT PANELS
RX-N600 (U, C models)
RX-N600 (R, T, K, A, G, E models)
RX-N600D (B model)

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
4
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
HTR-N5060 (U, C models)
DSP-N600 (J model)
HTR-N5060 (A, G models)

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
5
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
RX-N600 (U, C models)
■REAR PANELS
RX-N600 (R model)
RX-N600 (T model)

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
6
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
RX-N600 (K model)
RX-N600 (A model)
RX-N600 (G, E models)

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
7
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
RX-N600D (B model)
HTR-N5060 (U, C models)
HTR-N5060 (A model)

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
8
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
HTR-N5060 (G model)
DSP-N600 (J model)

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
9
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
■REMOTE CONTROL PANELS
RX-N600 (U, C models)
HTR-N5060 (U, C models)
RX-N600 (R, T, K, A, G, E models)
RX-N600D (B model)
HTR-N5060 (A, G models)
DSP-N600 (J model)

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
10
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
■SPECIFICATIONS / 参考仕様
■Audio Section / オーディオ部
Minimum RMS Output Power /定格出力
[RX-N600/RX-N600D]
(20 Hz to 20 kHz, 0.06 % THD, 8 ohms)
FRONT L/R ................................................................. 95 W + 95 W
CENTER ................................................................................. 95 W
SURROUND L/R ........................................................ 95 W + 95 W
SURROUND BACK ................................................................ 95 W
[HTR-N5060]
(1 kHz, 0.7 % THD, 8 ohms)
FRONT L/R ............................................................ 110 W + 110 W
CENTER ............................................................................... 110 W
SURROUND L/R ................................................... 110 W + 110 W
SURROUND BACK .............................................................. 110 W
[DSP-N600]
(20 Hz to 20 kHz, 0.09 % THD, 6 ohms)
FRONT L/R ................................................................. 95 W + 95 W
CENTER ................................................................................. 95 W
SURROUND L/R ........................................................ 95 W + 95 W
SURROUND BACK ................................................................ 95 W
Maximum Useful Output Power /実用最大出力 (EIAJ)
[RX-N600] (R, T, K models)
(1 kHz, 10 % THD, 8 ohms)
FRONT L/R ........................................................................... 135 W
CENTER ............................................................................... 135 W
SURROUND L/R .................................................................. 135 W
SURROUND BACK .............................................................. 135 W
[DSP-N600] (J model)
(1 kHz, 10 % THD, 6 ohms)
FRONT L/R ........................................................................... 135 W
CENTER ............................................................................... 135 W
SURROUND L/R .................................................................. 135 W
SURROUND BACK .............................................................. 135 W
Dynamic Power Per Channel /ダイナミックパワー (IHF)
[RX-N600/RX-N600D/HTR-N5060]
FRONT L/R (8/6/4/2 ohms) ............................. 130/165/195/240 W
[DSP-N600]
FRONT L/R (-/6/4/2 ohms) ................................... -/135/165/210 W
Maximum Output Power / MAXパワー
(SP IMPEDANCE SET: 8 ohms minimum/1 kHz, 0.7 % THD, 4 ohms)
[RX-N600/RX-N600D/HTR-N5060] (B, G, E models)
FRONT L/R ............................................................ 145 W + 145 W
CENTER ............................................................................... 145 W
SURROUND L/R ................................................... 145 W + 145 W
SURROUND BACK .............................................................. 145 W
Dynamic Headroom / ダイナミックヘッドルーム (IHF)
[RX-N600/HTR-N5060] (U, C models)
FRONT L/R (8 ohms) ........................................................... 1.6 dB
IEC Output Power /IECパワー (1 kHz, 0.06 % THD, 8 ohms)
[RX-N600/RX-N600D/HTR-N5060] (B, G, E models)
FRONT L/R ............................................................ 105 W + 105 W
Damping Factor / ダンピングファクタ
FRONT L/R (20 Hz to 20 kHz, 8 ohms) ...................... 120 or more
Maximum Input Voltage /最大許容入力 (1 kHz, 0.5 % THD)
CD, etc. (Effect on) .................................................... 2.2 V or more
Frequency Response /周波数特性
CD, etc. (10 Hz to 100 kHz) ........................................... +0/-3.0 dB
V-AUX (10 Hz to 20 kHz) ............................................... +0/-3.0 dB
Total Harmonic Distortion /全高調波歪率
(20 Hz to 20 kHz, 50 W/8 ohms)
CD, etc. to FRONT L/R ............................................ 0.06 % or less
Signal to Noise Ratio /信号対雑音比 (IHF-A Network)
CD, etc. to FRONT L/R
250 mV ................................................................. 100 dB or more
Residual Noise /残留ノイズ (IHF-A Network)
SP OUT ................................................................... 150 µV or less
Input Sensitivity/Input Impedance / 入力感度/入力インピーダンス
(1 KHz, 100 W/8 ohms)
CD, etc. ........................................................... 200 mV / 47 k-ohms
MULTI CH IN
FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER
.................................................................. 200 mV / 47 k-ohms
Rated Output Voltage/Output Impedance /
定格出力電圧/出力インピーダンス
OUT (REC) .................................................... 200 mV / 1.2 k-ohms
SUBWOOFER (2ch STEREO and FRONT SP: Small)
........................................................................ 4 V / 1.2 k-ohms
[RX-N600/RX-N600D/DSP-N600]
ZONE2 OUT .................................................. 200 mV / 1.2 k-ohms
Headphone Jack Rated Output Voltage/Impedance /
ヘッドフォン出力電圧/出力インピーダンス
CD, etc. (Input 1 kHz, 50 mV, 8 ohms) ........... 150 mV / 100 ohms
Channel Separation /チャンネルセパレーション
CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz)
................................................... 60 dB or more/45 dB or more
Volume Control / 可変範囲
........................................... MUTE/-80 dB to +16 dB/1 dB step
Tone Control Characteristics / トーンコントロール特性
(FRONT L/R)
BASS
Boost/Cut ............................................ ±10 dB/2 dB step (60 Hz)
TREBLE
Boost/Cut ........................................... ±10 dB/2 dB step (20 kHz)
Filter Characteristics / フィルタ特性
FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK
Small (H.P.F.)
............ fc= 40/60/80/90/100/110/120/160/200 Hz / 12 dB/oct.
SUBWOOFER (L.P.F.)
............ fc= 40/60/80/90/100/110/120/160/200 Hz / 24 dB/oct.
■Video Section /ビデオ部
Video Format (Gray Back) / グレーバック
U, C, R, K, J models .............................................................. NTSC
T, A, B, G, E models ................................................................ PAL
Video Format (Video Conversion) /
ビデオ信号方式（ビデオコンバージョン）
............................................................................... NTSC / PAL
Composite Video Rated Input Voltage /
コンポジットビデオ信号レベル
....................................................................... 1 Vp-p / 75 ohms
S-Video Rated Input Voltage / Sビデオ信号信号レベル
Y ........................................................................... 1 Vp-p / 75 ohms
C ................................................................... 0.286 Vp-p / 75 ohms
Component Video Rated Input Voltage /
コンポーネントビデオ信号レベル
Y ........................................................................... 1 Vp-p / 75 ohms
Cb/Cr ................................................................ 0.7 Vp-p / 75 ohms
D4-Video Signal Level Rated Input Voltage /
D4ビデオ信号レベル (J model)
Y ........................................................................... 1 Vp-p / 75 ohms
Cb/Cr ................................................................ 0.7 Vp-p / 75 ohms
Maximum Input Voltage / 最大許容入力
VIDEO CONV. OFF ............................................. 1.5 Vp-p or more
Signal to Noise Ratio / S/N比 .................................... 50 dB or more
Frequency Response (Monitor Out ) / 周波数特性
(VIDEO CONV. OFF)
Component video signal level / コンポーネントビデオ信号
.................................................................. 5 Hz to 60 MHz, -3 dB
D4-video signal level / D4ビデオ信号 (J model)
.................................................................. 5 Hz to 60 MHz, -3 dB

11
RX-N600/RX-N600D/HTR-N5060/
DSP-N600
Dimensions /寸法 (W x H x D)
[RX-N600/RX-N600D/DSP-N600]
..................... 435 x 171 x 393.2 mm (17-1/8" x 6-3/4" x 15-1/2")
[HTR-N5060]
................... 435 x 161 x 391.2 mm (17-1/8" x 6-5/16" x 15-3/8")
Weight /質量
[RX-N600/DSP-N600]
................................................................ 11.7 kg (25 lbs. 12 oz.)
[RX-N600D]
.................................................................. 11.9 kg (26 lbs. 3 oz.)
[HTR-N5060]
................................................................ 11.2 kg (24 lbs. 11 oz.)
Finish/仕上げ
[RX-N600/RX-N600D]
Gold color .................................................................... R, T models
Black color ........................................... U, C, R, A, B, G, E models
Titanium color ................................................ C, K, B, G, E models
[HTR-N5060]
Black color ................................................................... U, C models
Silver color ......................................................... U, C, A, G models
[DSP-N600]
Gold color ........................................................................... J model
Accessories /付属品
Remote control x 1, Batteries x 2, Indoor FM antenna x 1, AM loop
antenna x 1, Indoor DAB antenna x 1 (B model)
* Specifications are subject to change without notice due to product
improvements.
※ 参考仕様および外観は予告なく変更されることがあります。
U .......... U.S.A. model C ...... Canadian model
R .......... General model T ....... Chinese model
K .......... Korean model A ...... Australian model
B .......... British model G ...... European model
E .......... South European model J ....... Japanese model
Unit: mm (inch)
単位：mm（インチ）
435 (17-1/8")
171 (6-3/4")
150 (5-15/16") 352.2 (13-7/8")
21
(13/16")
19
(3/4") 393.2 (15-1/2")
22
(7/8")
161 (6-5/16")
140 (5-1/2") 348.2 (13-11/16")
21
(13/16")
21
(13/16") 391.2 (15-3/8")
22
(7/8")
RX-N600D
RX-N600
DSP-N600
HTR-N5060
• DIMENSIONS / 寸法図
■FM Section/FM部
Tuning Range / 受信周波数
U, C models ....................................................... 87.5 to 107.9 MHz
R model ................................ 87.5 to 108.0 / 87.50 to 108.00 MHz
T, K, A, B, G, E models ................................. 87.50 to 108.00 MHz
J model ................................................................ 76.0 to 90.0 MHz
50 dB Quieting Sensitivity / 50dBSN感度(IHF)(1 kHz, 100 % Mod.)
Mono / Stereo ........................ 2.0 µV (17.3 dBf) / 25 µV (39.2 dBf)
Usable Sensitivity / 実用感度(IHF)
Mono .................................................................... 1.0 µV (11.2 dBf)
Selectivity / 選択度 (at 400 kHz) .............................................. 70 dB
Signal to Noise Ratio / S/N比(IHF)
Mono / Stereo ............................................................ 76 dB / 70 dB
Harmonic Distortion / 歪率 (1 kHz)
Mono / Stereo ............................................................ 0.2 % / 0.3 %
Stereo Separation / ステレオセパレーション
1 kHz ...................................................................................... 42 dB
Frequency Response / 周波数特性
20 Hz to 15 kHz .............................................................. +0.5/-2 dB
Antenna Input / アンテナ入力 ......................... 75 ohms unbalanced
■AM Section / AM部
Tuning Range / 受信周波数
U, C models ......................................................... 530 to 1,710 kHz
R model ....................................... 530 to 1,710 / 531 to 1,611 kHz
T, K, A, B, G, E, J models ................................... 531 to 1,611 kHz
Usable Sensitivity / 実用感度 ............................................ 300 µV/m
Antenna / アンテナ入力 .............................................. Loop antenna
■DAB Section(B model)
Tuning Range
Band III .................................................................. 174 to 240 MHz
L-band .............................................................. 1,452 to 1,492 MHz
Sensitivity
Band III .............................................................................. -99 dBm
L-band ................................................................................ -95 dBm
Selectivity (for adjacent channel)
Band III ............................................................................... 40 dBm
L-band ................................................................................. 40 dBm
Signal to Noise Ratio
............................................................................................ 97 dB
Total Harmonic Distortion
.......................................................................................... 0.01 %
Stereo Separation
1 kHz ...................................................................................... 95 dB
Frequency Response
20 Hz to 20 kHz ........................................................... +0.5/-0.5 dB
Antenna Input .................................................. 75 ohms unbalanced
■General /総合
Power Supply /電源電圧
U, C models .......................................................... A C 120 V, 60 Hz
R model .............................. AC 110/120/220/230-240 V, 50/60 Hz
T model ................................................................. AC 220 V, 50 Hz
K model................................................................. AC 220 V, 60 Hz
A model................................................................. AC 240 V, 50 Hz
B, G, E models ..................................................... AC 230 V, 50 Hz
J model ............................................................ AC 100V, 50/60 Hz
Power Consumption/ 消費電力
U, C models ........................................................... 350 W / 440 VA
R, T, K, A, B, G, E models ................................................... 360 W
J model ................................................................................. 250 W
Standby Power Consumption (reference data)/待機時消費電力（参考値）
............................................................................................ 0.1 W
Maximum Power Consumption / 最大消費電力(R model)
6ch Drive, 10 % THD ........................................................... 700 W
AC Outlets/ACアウトレット
2 Switched Outlets
U, C, T, J models................................................. 100 W max. total
R, B, G, E models ................................................. 50 W max. total
1 Switched Outlet
A model........................................................................ 100 W max.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of
Dolby Laboratories.
ドルビーラボラトリーズからの実施権により製造されています。「ドル
ビー」、「PROLOGIC」、「SurroundEX」およびダブルD記号 は、ド
ルビーラボラトリーズの商標です。
Manufactured under license from Digital Theater Systems, Inc.
“DTS”, “DTS-ES”, “NEO:6”, and “DTS 96/24” are trademarks of
Digital Theater Systems, Inc. Copyright 1996, 2003 Digital
Theater Systems, Inc. All right reserved.
DTS、DTS-ESExtendedSurround、NEO:6およびDTS96／24はデジ
タルシアターシステムズの登録商標です。
“iPod” is a trademark of Apple Computer, Inc., registered in the
U.S. and other countries.
iPodは、米国およびその他の国々で登録されたAppleComputer,Inc.
の商標または登録商標です。
This receiver supports network connections.
“SILENT CINEMA” is a trademark of YAMAHA CORPORATION.
「サイレントシネマ SILENTCINEMA」はヤマハ株式会社の登録商標
です。
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
Neural Surround™ name and related logos are trademarks
owned by Neural Audio Corporation.
This receiver supports DAB tuning.
AACロゴマーク はドルビーラボラトリーズの商標です。
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
MPEGLayer3音声圧縮技術は、FraunhoferIISおよびThomsonによっ
てライセンス供与されています。
The “DAB Digital Radio” logo and the stylised “r” mark ® and ©
Digital One Limited.

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
12
Frequency Channel label
1452.960 MHz LA
1454.672 MHz LB
1456.384 MHz LC
1458.096 MHz LD
1459.808 MHz LE
1461.520 MHz LF
1463.232 MHz LG
1464.944 MHz LH
1466.656 MHz LI
1468.368 MHz LJ
1470.080 MHz LK
1471.792 MHz LL
1473.504 MHz LM
1475.216 MHz LN
1476.928 MHz LO
1478.640 MHz LP
1480.352 MHz LQ
1482.064 MHz LR
1483.776 MHz LS
1485.488 MHz LT
1487.200 MHz LU
1488.912 MHz LV
1490.624 MHz LW
Frequency Channel label
174.928 MHz 5A
176.640 MHz 5B
178.352 MHz 5C
180.064 MHz 5D
181.936 MHz 6A
183.648 MHz 6B
185.360 MHz 6C
187.072 MHz 6D
188.928 MHz 7A
190.640 MHz 7B
192.352 MHz 7C
194.064 MHz 7D
195.936 MHz 8A
197.648 MHz 8B
199.360 MHz 8C
201.072 MHz 8D
202.928 MHz 9A
204.640 MHz 9B
206.352 MHz 9C
208.064 MHz 9D
209.936 MHz 10A
211.648 MHz 10B
213.360 MHz 10C
215.072 MHz 10D
CATEGORY MAIN MENU SELECT MENU VALUE [INITIAL] CATEGORY MAIN MENU SUB MENU SELECT MENU VALUE [INITIAL]
ROOM : S >M L
SUBWOOFER : YES
SPEAKER : 6spk
SETUP : OK
CHECK OK? : YES
FR ·····||·····
C ·····||·····
SL ·····||·····
SB ·····||·····
SR ·····||·····
SWFR ·····||·····
FRONT : LARGE
CENTER : SML
SURROUND L/R : SML
SURROUND BACK : SML
BASS OUT : BOTH
CROSS OVER : 80Hz
SUBWOOFER PHASE : NORMAL
FL ·····||·····
FR ·····||·····
C ·····||·····
SL ·····||·····
SR ·····||·····
SB ·····||·····
SWFR ·····||·····
UNIT : meters
FRONT L : 10.0ft/3.00m
FRONT R : 10.0ft/3.00m
CENTER : 10.0ft/3.00m
SURR. L : 10.0ft/3.00m
SURR. R : 10.0ft/3.00m
SURR. B : 7.0ft/2.10m
SWFR : 10.0ft/3.00m
TEST : >OFF ON
100Hz ·····||····· 0dB
300Hz ·····||····· 0dB
1kHz ·····||····· 0dB
3kHz ·····||····· 0dB
10kHz ·····||····· 0dB
SPEAKER LFE : 0dB
HEADPHONE LFE : 0dB
SPEAKER : MAX
HEADPHONE : MAX
MUTING TYPE : FULL
AUDIO DELAY : 0ms
TONE BYPASS : AUTO
DUAL MONO : MAIN ( J model )
CMPNT-V INPUT [A]
CMPNT-V INPUT [B]
CMPNT-V INPUT [C]
OPTICAL OUT (1)
OPTICAL IN (2)
OPTICAL IN (3)
OPTICAL IN (4)
COAXIAL IN (5)
S / [M] / L
[YES] / NONE
2spk / 3spk / 4 spk / 5spk / [6spk]
[OK] / CANCEL
[YES] / NO
±10.0dB step
SMALL / [LARGE]
NONE / [SML] / LRG
SWFR / FRONT / [BOTH]
40 / 60 / [80] / 90 / 100 / 110 / 120 / 160 / 200 Hz
[NORMAL] / REVERSE
-10dB to +10dB [CENTER 0dB], 0.5dB step
feet / [meters]
feet: 1.0 to 80.0ft [10.0ft], 0.5ft step
meters: 0.30 to 24.00m [3.00m], 0.10m step
[OFF] / ON
-6dB to +6dB [0dB], 1dB step
-20dB to 0dB [0dB], 1dB step
MIN / STD / [MAX]
-20 dB / [FULL]
0ms to 160ms, 1ms step
OFF / [AUTO]
[MAIN] / SUB / ALL
[DVD] / DTV/CBL / V-AUX / DVR
DVD / [DTV/CBL] / V-AUX / DVR
DVD / DTV/CBL / V-AUX / [DVR]
CD / [MD/CD-R] / DVD / DTV/CBL / V-AUX / DVR
CD / [MD/CD-R] / DVD / DTV/CBL / V-AUX / DVR
CD / MD/CD-R / [DVD] / DTV/CBL / V-AUX / DVR
CD / MD/CD-R / DVD / [DTV/CBL] / V-AUX / DVR
[CD] / MD/CD-R / DVD / DTV/CBL / V-AUX / DVR
[AUTO] / LAST
CD / MD/CD-R / DVD / DTV/CBL / V-AUX / DVR
• SET MENU TABLE / セットメニュー
3DAB
MENU
(B model)
3 NET /
USB
MENU
(U, C, R,
T, K, A,
G, E, J
models)
4 NET /
USB
MENU
(B model)
4 OPTION
MENU
(U, C, R,
T, K, A,
G, E, J
models)
5 OPTION
MENU
(B model)
D) VOLUME TRIM
A) INIT SCAN
B) TUNE AID
C) DRC MENU
D) PRUNE LIST
E) PRESET DELETE
A) NETWORK
B) PLAY STYLE
C) INFORMATION
A) DISPLAY SET
B) MEMORY GUARD
C) PARAM. INI
D) MULTI ZONE SET
E) XM RADIO SET
(U, C models)
SCAN : FULL
5A LEVEL : XX
DRC MODE : AUTO
OK : [ENTER]
DELETE : XX
DHCP : ON
IP xxx. xxx. xxx. xxx
SUBNET 255. 255. 255. 000
GATEWAY xxx. xxx. xxx. xxx
DNS (P) xxx. xxx. xxx. xxx
DNS (S) xxx. xxx. xxx. xxx
SET / CANCEL
REPEAT : OFF
SHUFFLE : OFF
MAC ADDRESS xx. xx. xx. xx. xx. xx
STATUS :
DIMMER : 0
VIDEO CONV. : ON
OSD SHIFT : 0
GRAY BACK : AUTO
ON SCREEN : 10S
FL SCROLL : CONT
MEMORY GUARD : OFF
SP B : FRONT
XM DISPLAY : 10S
XM ANTENNA : NONE
SCROLL : CONT
-6.0dB to +6.0dB [0dB] 0.5dB step
CD / MD/CD-R / DVD / DTV/CBL / V-AUX / DVR
[FULL] / UK_BAND3 / NO
[5A] / LW (DAB channel label)
[AUTO] / OFF
YES / NO
XX (Preset number)
[ON] / OFF
0 to 255
[OFF] / SINGLE / ALL
[OFF] / ON
-4 to 0 [0], 1 step
OFF / [ON]
-5 to +5, 1step
OFF / [AUTO]
ON / [10S] / 30S
[CONT] / ONCE
[OFF] / ON
STEREO / MUSIC / ENTERTAINMENT / MOVIE THEATER / STANDARD
[FRONT] / ZONE B
[10S] / 30S / OFF
0% to 100% / [NONE]
[CONT] / ONCE
• DAB FREQUENCY TABLE
Frequency Channel label
216.928 MHz 11A
218.640 MHz 11B
220.352 MHz 11C
222.064 MHz 11D
223.936 MHz 12A
225.648 MHz 12B
227.360 MHz 12C
229.072 MHz 12D
230.784 MHz 13A
232.496 MHz 13B
234.208 MHz 13C
235.776 MHz 13D
237.488 MHz 13E
239.200 MHz 13F
Band 3 L-Band
SUB MENU
A) SPEAKER SET
B) SPEAKER LEVEL
C) SP DISTANCE
D) CENTER GEQ
E) LFE LEVEL
F) DYNAMIC RANGE
G) AUDIO SET
A) I/O ASSIGNMENT
B) INPUT MODE
C) INPUT RENAME
BASIC
SETUP
MANUAL
SETUP
1 SOUND
MENU
2 INPUT
MENU

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
13
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
■INTERNAL VIEW
• RX-N600/RX-N600D/DSP-N600
• HTR-N5060
OPERATION (4) P.C.B.
NET P.C.B.
FUNCTION (2) P.C.B.
DSP P.C.B.
MAIN (5) P.C.B.
MAIN (4) P.C.B.
VIDEO P.C.B.
Tuner
FUNCTION (1) P.C.B.
MAIN (1) P.C.B.
FUNCTION (4) P.C.B.
OPERATION (7) P.C.B.
OPERATION (6) P.C.B.
MAIN (2) P.C.B.
OPERATION (1) P.C.B.
Power Transformer
OPERATION (3) P.C.B.
EBCDG F
0
9
A
132 4 5 6 7 8
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
G
OPERATION (4) P.C.B.
FUNCTION (2) P.C.B.
NET P.C.B.
DAB P.C.B. (B model)
FUNCTION (3) P.C.B. (R model)
DSP P.C.B.
MAIN (5) P.C.B.
MAIN (4) P.C.B.
VIDEO P.C.B.
Tuner
FUNCTION (1) P.C.B.
MAIN (1) P.C.B.
FUNCTION (4) P.C.B.
MAIN (2) P.C.B.
Power Transformer
OPERATION (7) P.C.B.
OPERATION (1) P.C.B.
OPERATION (6) P.C.B.
OPERATION (3) P.C.B.
OPERATION (2) P.C.B.
DE
H FGJ I
B
A
C
12453 6 7 8 9 0
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
G
H
I
J

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
14
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
■DISASSEMBLY PROCEDURES / 分解手順
Fig. 1
(Remove parts in the order as numbered.)
Disconnect the power cable from the AC outlet.
1. Removal of Top Cover
a. Remove 4 screws (1), 5 screws (2) and 1 screw (3).
(Fig. 1)
b. Slide the Top Cover rearward to remove it. (Fig. 1)
2. Removal of Front Panel Unit
a. Remove 2 Knobs. (Fig. 1)
b. Remove 1 screw (4) and then remove the Support Top.
(Fig. 1)
c. Remove 6 screws (5). (Fig. 1)
d. Remove the Front Panel Unit. (Fig. 1)
3. Removal of Plate Side
a. Remove 2 push rivets (6). (Fig. 1)
b. Remove the Plate Side L/R. (Fig. 1)
4. Removal of Sub Chassis Unit
a. Remove 2 screws (7) and then slide the Sub Chassis
Unit forward. (Fig. 1)
b. Remove 1 push rivet (8). (Fig. 1)
c. Remove the Barrier/FFC. (Fig. 1)
d. Remove CB5, CB203, CB205, CB312 and CB603.
(Fig. 1)
e. Remove the Sub Chassis Unit. (Fig. 1)
RX-N600/RX-N600D/DSP-N600
（番号順に部品を取り外してください。）
AC電源コンセントから、電源コードを抜いてください。
1. トップカバーの外し方
a. 1のネジ4本、2のネジ5本、3のネジ1本を外します。
（Fig.1）
b. トップカバーを後方へスライドさせ、取り外します。（Fig.1）
2. フロントパネルユニットの外し方
a. ノブを2個取り外します。（Fig.1）
b. 4のネジ1本を外し、サポートトップを取り外します。
（Fig.1）
c. 5のネジ6本を外します。（Fig.1）
d. フロントパネルユニットを取り外します。（Fig.1）
3. プレートサイドL/Rの外し方
a. 6のプッシュリベット2本を外します。（Fig.1）
b. プレートサイドL/Rを取り外します。（Fig.1）
4. サブシャーシユニットの外し方
a. 7のネジ2本を外し、サブシャーシユニットを前方に引き出し
ます。（Fig.1）
b. 8のプッシュリベット1本を外します。(Fig.1）
c. バリアー/FFCを取り外します。(Fig.1）
d. CB5、CB203、CB205、CB312、CB603を外します。
(Fig.1）
e. サブシャーシーユニットを取り外します。(Fig.1）
1
1
2
3
2
CB205
CB603
CB203
CB5
Top Cover
トップカバー
Front Panel Unit
フロントパネルユニット
Knob
ノブ
Support Top
サポートトップ CB312
Sub Chassis Unit
サブシャーシユニット
Plate Side L
プレートサイドL
BARRIER / FFC
バリアーFFC
Plate Side R
プレートサイドR
4
5
5
6
6
8
7
7

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
15
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
5. Removal of FUNCTION (1) P.C.B.
a. Remove 2 screws (9). (Fig. 2)
b. Remove 8 screws (0). (Fig. 4)
c. Remove CB200-202, CB204, CB206, CB207 and
CB751. (Fig. 2)
d. Remove the FUNCTION (1) P.C.B.. (Fig. 2)
6. Removal of DSP P.C.B.
a. Remove 2 screws (A). (Fig. 2)
b. Remove 6 screws (U, C models) / 6 screws (R, T, K, A,
B, G, E models) (B). (Fig. 4)
c. Remove CB2-4, CB6, CB9, and CB57. (Fig. 2)
d. Remove CB8 and CB53. (B model) (Fig. 2)
e. Remove the DSP P.C.B.. (Fig. 2)
7. Removal of NET P.C.B.
a. Remove 1 screw (C). (Fig. 2)
b. Remove 2 screws (D). (Fig. 4)
c. Remove CB605. (Fig. 2)
d. Remove the NET P.C.B.. (Fig. 2)
8. Removal of VIDEO P.C.B.
a. Remove 1 push rivet (E). (Fig. 3)
b. Remove 6 screws (F). (Fig. 4)
c. Remove CB401 and CB402. (Fig. 3)
d. Remove the VIDEO P.C.B.. (Fig. 3)
Fig. 3
5. FUNCTION（1）P.C.B.の外し方
a. 9のネジ2本を外します。(Fig.2）
b. 0のネジ8本を外します。(Fig.4）
c. CB200〜202、CB204、CB206、CB207、CB751を
外します。（Fig.2）
d. FUNCTION（1）P.C.B.を取り外します。（Fig.2）
6. DSPP.C.B.の外し方
a. Aのネジ2本を外します。(Fig.2）
b. Bのネジ6本を外します。（Fig.4）
c. CB2〜4、CB6、CB57を外します。（Fig.2）
d. DSPP.C.B.を取り外します。（Fig.2）
7. NETP.C.B.の外し方
a. Cのネジ1本を外します。(Fig.2）
b. Dのネジ2本を外します。（Fig.4）
c. CB605のネジを外します。（Fig.2）
d. NETP.C.B.を取り外します。（Fig.2）
8. VIDEOP.C.B.の外し方
a. Eのプッシュリベット1本を外します。（Fig.3）
b. Fのネジ6本を外します。(Fig.4）
c. CB401、CB402を外します。（Fig.3)
d. VIDEOP.C.B.を取り外します。（Fig.3）
CB202
CB204
CB206
CB200
CB207
CB201
CB2CB3
CB9
CB4
CB57
CB6
CB751
CB605
FUNCTION (1) P.C.B.
DSP P.C.B.
NET P.C.B.
9AA
C
CB53
(
B model )
CB8
( B model )
CB402CB103
CB401
FUNCTION (2) P.C.B. VIDEO P.C.B.
E
G
CB105
(
U, C, B models )
CB104
CB395
CB331
Fig. 2

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
16
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
9. Removal of FUNCTION (2) P.C.B.
a. Remove 1 push rivet (G). (Fig. 3)
b. Remove 5 screws (H). (Fig. 4)
c. Remove the FUNCTION (2) P.C.B.. (Fig. 3)
10.Removal of TUNER
a. Remove 3 screws (I). (Fig. 4)
b. Remove the TUNER. (Fig. 5)
11.Removal of DAB P.C.B. (B model)
a. Remove 2 screws (J). (Fig. 4)
b. Remove the DAB P.C.B.. (Fig. 5)
12.Removal of MAIN (1), (2), (4) and (5) P.C.B.s
a. Remove the Artbase/P.C.B.. (Fig. 5)
b. Remove 2 screws (K), 1 screw (L), 2 screws (M) and
1 screw (N). (Fig. 5)
c. Remove 5 screws (O). (Fig. 4)
d. Remove CB103, CB104, CB105 (U, C, B models),
CB331 and CB395. (Fig. 3)
e. Remove MAIN (1), (2), (4) and (5) P.C.B.s together with
the Heat Sink. (Fig. 5)
Fig. 4
Fig. 5
9. FUNCTION（2）P.C.B.の外し方
a. Gのプッシュリベット1本を外します。（Fig.3）
b. Hのネジ9本を外します。(Fig.4）
c. FUNCTION（2）P.C.B.を取り外します。（Fig.3)
10.TUNERの外し方
a. Iのネジ3本を外します。（Fig.4）
b. TUNERを取り外します。（Fig.5）
11. MAIN（1）、（2）、（4）、（5）P.C.B.の外し方
a. アートベース/PCBを取り外します。（Fig.5）
b. Kのネジ2本、Lのネジ1本、Mのネジ2本、Nのネジ1本を
外します。（Fig.5）
c. Oのネジ5本を外します。（Fig.4）
d. CB103、CB104、CB331、CB395を外します。（Fig.3）
e. MAIN（1）、（2）、（4）、（5）P.C.B.をヒートシンクと一緒に取
り外します。（Fig.5）
0
I HO
F B D
J model
U, C models
J
(B model)
N
L
K
K
M
MAIN (1) P.C.B.
MAIN (2) P.C.B.
MAIN (4) P.C.B.
MAIN (5) P.C.B.
DAB P.C.B.
(B model)
TUNER
チューナー
Heat Sink
ヒートシンク
Artbase / P.C.B.
アートベース/P.C.B.

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
17
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
Fig. 6
When checking the P.C.B.:
• Put a cloth over the equipment. Put the P.C.B.s
together with the heat sink upright on the cloth and
check them. (Fig. 6)
• Reconnect all cables (connectors) that have been
disconnected.
• When connecting the flat cable, use care for the
polarity.
• The P.C.B. removed from the chassis does not work
because its grounding is loose. Be sure to connect
the ground of rear panel, MAIN (1) P.C.B. (G1001)
and OPERATION (4) P.C.B. (G3001) to the chassis
with a ground lead or the like. (Fig. 6)
P.C.B.チェックする場合
・ 布を敷きます。その上にP.C.B.をヒートシンクと一緒に立
ててチェックします。（Fig.6)
・ 外したケーブル（コネクター）をすべて接続してください。
・ フラットケーブルを接続する際、極性に注意してくださ
い。
・ シャーシから外したP.C.B.はアースが浮いて動作しません
ので、MAIN（1）P.C.B.（G1001）、OPERATION（4）
P.C.B.（G3001）のアースをリード線等でシャーシまたは
GNDに接続してください。（Fig.6)
Cloth
布
Ground Lead
アース線
Ground Lead
アース線
G3001
G1001
MAIN (1) P.C.B. OPERATION (4) P.C.B.

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
18
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
1
1
2
3
2
CB205
CB203
CB5
Top Cover
Front Panel Unit
CB310
Barrier / FFC
4
4
4
5
CB603
■DISASSEMBLY PROCEDURES
(Remove parts in the order as numbered.)
Disconnect the power cable from the AC outlet.
1. Removal of Top Cover
a. Remove 4 screws (1), 5 screws (2) and 1 screw (3).
(Fig. 1)
b. Slide the Top Cover rearward to remove it. (Fig. 1)
2. Removal of Front Panel Unit
a. Remove 6 screws (4). (Fig. 1)
b. Remove 1 push rivet (5). (Fig. 1)
c. Remove the Barrier/FFC. (Fig. 1)
d. Remove CB5, CB203, CB205, CB310 and CB603.
(Fig. 1)
e. Remove the Front Panel Unit. (Fig. 1)
Fig. 1
Fig. 2
HTR-N5060
CB202
CB204
CB206
CB200
CB207
CB201
CB2CB3
CB9
CB4
CB57
CB6
CB751
CB605
FUNCTION (1) P.C.B.
DSP P.C.B.
NET P.C.B.
688
0

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
19
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
Fig. 3
3. Removal of FUNCTION (1) P.C.B.
a. Remove 2 screws (6). (Fig. 2)
b. Remove 8 screws (7). (Fig. 4)
c. Remove CB200-202, CB204, CB206, CB207 and
CB751. (Fig. 2)
d. Remove the FUNCTION (1) P.C.B.. (Fig. 2)
4. Removal of DSP P.C.B.
a. Remove 2 screws (8). (Fig. 2)
b. Remove 7 screws (9) (U, C models)/6 screws (A, G
models) (9). (Fig. 4)
c. Remove CB2-4, CB6, CB9 and CB57. (Fig. 2)
d. Remove the DSP P.C.B.. (Fig. 2)
5. Removal of NET P.C.B.
a. Remove 1 screw (0). (Fig. 2)
b. Remove 2 screws (A). (Fig. 4)
c. Remove CB605. (Fig. 2)
d. Remove the NET P.C.B.. (Fig. 2)
Fig. 4
6. Removal of VIDEO P.C.B.
a. Remove 1 push rivet (B). (Fig. 3)
b. Remove 6 screws (C). (Fig. 4)
c. Remove CB401 and CB402. (Fig. 3)
d. Remove the VIDEO P.C.B.. (Fig. 3)
7. Removal of FUNCTION (2) P.C.B.
a. Remove 1 push rivet (D). (Fig. 3)
b. Remove 5 screws (E). (Fig. 4)
c. Remove the FUNCTION (2) P.C.B.. (Fig. 3)
8. Removal of TUNER P.C.B.
a. Remove 3 screws (F). (Fig. 4)
b. Remove the TUNER. (Fig. 5)
CB402CB103
CB401
CB105
(
U, C models )
CB104
FUNCTION (2) P.C.B. VIDEO P.C.B.
B
CB331
CB395
D
7
F EK
C 9 A
U, C models

RX-N600/RX-N600D/HTR-N5060/
DSP-N600
20
RX-N600/RX-N600D/
HTR-N5060/DSP-N600
When checking the P.C.B.:
•Put a cloth over the equipment. Put the P.C.B.s together with the heat sink upright on the cloth and check them. (Fig. 6)
•Reconnect all cables (connectors) that have been disconnected.
•When connecting the flat cable, use care for the polarity.
•The P.C.B. removed from the chassis does not work because its grounding is loose. Be sure to connect the ground of rear
panel, MAIN (1) P.C.B. (G1001) and OPERATION (4) P.C.B. (G3001) to the chassis with a ground lead or the like.
Fig. 5
Fig. 6
9. Removal of MAIN (1), (2), (4) and (5) P.C.B.s
a. Remove the Artbase/P.C.B.. (Fig. 5)
b. Remove 2 screws (G), 1 screw (H), 2 screws (I) , 1 screw (J). (Fig. 5)
c. Remove 5 screws (K). (Fig. 4)
d. Remove CB103, CB104, CB105 (U, C models), CB331 and CB395. (Fig. 3)
e. Remove MAIN (1), (2), (4) and (5) P.C.B.s together with the Heat Sink. (Fig. 5)
J
H
G
G
I
TUNER
Heat Sink
Artbase / P.C.B.
MAIN (1) P.C.B.
MAIN (2) P.C.B.
MAIN (4) P.C.B. MAIN (5) P.C.B.
Cloth
Ground Lead
Ground Lead
G3001
G1001
MAIN (1) P.C.B. OPERATION (4) P.C.B.