Yamaha Crd-hd1300 User manual

There are two types of CDR-HD1300; one equipped with a

hard disc drive and the other without it depending on

market areas.

CDR-HD1300E is equipped with a hard disc drive.

CDR-HD1300/CDR-HD1300E

CDR-HD1300には販売地域によりハードディスクドライブ

が搭載されているものと、搭載されていないものがありま

す。

CDR-HD1300Eにはハードディスクドライブが搭載されて

います。

100813

P.O.Box 1, Hamamatsu, Japan

■CONTENTS

TO SERVICE PERSONNEL ...................................... 2~3

PREVENTION OF ELECTRO STATIC DISCHARGE ... 4

FRONT PANELS ............................................................ 5

REAR PANELS .......................................................... 5~6

REMOTE CONTROL PANELS ...................................... 7

SPECIFICATIONS.......................................................... 7

INTERNAL VIEW ........................................................... 8

DISASSEMBLY PROCEDURE / 分解手順 .............. 9~15

SERVICE CHECK PROCEDURES /

サービスチェック手順 ............................................ 16~19

INSPECTIONS/検査 ............................................. 20~25

FIRMWARE UPDATE / ファームウエアの更新 .. 26~27

FORMATTING THE HDD / HDDのフォーマット ........ 27

Entering ID to main P.C.B. /

メインPCBへのID書き込み .................................... 28~29

DISPLAY DATA ..................................................... 30~31

IC DATA ................................................................. 32~39

BLOCK DIAGRAM ....................................................... 40

PRINTED CIRCUIT BOARD .................................. 41~44

SCHEMATIC DIAGRAM ........................................ 45~49

PARTS LIST ........................................................... 50~67

REMOTE CONTROL.................................................... 68

Parts List for Carbon Resistors ................................ 69

SERVICE MANUAL

HDD/CD RECORDER

CDR-HD1300/CDR-HD1300E

IMPORTANT NOTICE

This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.

It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already

known and understood by the users, and have therefore not been restated.

WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal

injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,

we advise all YAMAHA product owners that any service required should be performed by an authorized

YAMAHA Retailer or the appointed service representative.

IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or

recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and

service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable

and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please

contact the distributor's Service Division.

WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).

IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

WALL

OUTLET EQUIPMENT

UNDER TEST

AC LEAKAGE

TESTER OR

EQUIVALENT

INSULATING

TABLE

■TO SERVICE PERSONNEL

1. Critical Components Information

Components having special characteristics are marked s

and must be replaced with parts having specifications equal

to those originally installed.

2. Leakage Current Measurement (For 120V Models Only)

When service has been completed, it is imperative to verify

that all exposed conductive surfaces are properly insulated

from supply circuits.

●Meter impedance should be equivalent to 1500 ohm shunted

by 0.15µF.

●Leakage current must not exceed 0.5mA.

●Be sure to test for leakage with the AC plug in both polarities.

THE COMPACT DISC RECORDER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED

SERVICE PERSONNEL.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plastic

(where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency

(and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-

SON WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose

eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before

handling food.

WARNING: Laser Safety

This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may

cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during

servicing of the unit.

1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from

the laser pick-up unit at all times. Do not stare at the laser beam at any time.

2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.

3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in

hazardous radiation exposure.

Laser Emitting conditions:

1. This device is a Class IIIb laser device.

Class IIIb means

With the protective case removed, exposure to the light output from the laser, either directly or reflected by a mirror, can

cause harm to the eyes, but there is no danger to the eyes from exposure to dispersed reflected laser light. (Generally 0.5

W or less)

2. Always wear eyeglasses designed for protection against laser light.

3. Always wear gloves.

4. Have no reflective objects anywhere near this device.

5. Figure A shows from where in this device the laser is emitted.

6. When switching on the power to the device for the first time, always measure the laser power with a laser power meter

and check that the power is no greater than the number of Watts in the specifications.

7. Never look directly at the laser light while the laser is emitting light.

8. Do not allow the laser light to shine directly on your skin while the laser is emitting light.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPART

PRODUIT LASER DE CLASSE 1

LINE IN — LINE OUT IN OUT

DIGITAL

REC COAXIAL OPTICAL COAXIAL OPTICAL

RS–232C

VIDEO

OUT

S VIDEO

ANALOG

PLAY

4 3

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPART

PRODUIT LASER DE CLASSE 1

U model

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPART

PRODUIT LASER DE CLASSE 1

LINE IN —LINE OUT IN OUT

DIGITAL

REC COAXIAL OPTICAL COAXIAL OPTICAL

RS–232C

VIDEO

OUT

S VIDEO

ANALOG

PLAY

4 3

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPART

PRODUIT LASER DE CLASSE 1

B, G models

VARO!: AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASER-

SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING!: OSYNLIG LASERSTRÅLNING NÄR

DENNA DEL ÄR ÖPPNAD OCH SPÄRREN

ÄR URKOPPLAD. BETRAKTA EJ

STRÅLEN.

Laser Radiation Point

Fig. A

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs a laser. Therefore, be sure to carefully

follow the instructions below when servicing.

1. Laser Diode Properties

•Material : GaAlAs

•Wavelength : 780-787 nm

•Emission Duration : Pulse

•Laser Output : Read mode 0.7mW (Continuous) ✻

Write mode max. 38mW ✻

(for 166ns, Min. Cycle 86.6ns)

✻This output is the value measured at the lens of the Laser Pickup

Unit.

2. When checking the laser diode emission, keep your eyes more than

30 cm away from the objective lens.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

■PREVENTION OF ELECTRO STATIC DISCHARGE

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor “chip”components. The following techniques should be used to help reduce the incidence of component damage caused by

electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by

touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be

removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to

prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)”can generate

electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable

conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the

chassis or circuit assembly into which the device will be installed.

CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing

together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an

ES device).

Grounding for electrostatic breakdown prevention

1. Human body grounding:

Use an anti static wrist strap to discharge the static electricity

from your body.

2. Work table grounding:

Put a grounded conductive material (sheet) or iron sheet on

the area where the optical pickup is placed.

Caution:

The static electricity of your clothes will not be grounded

through the wrist strap. So take care not to let your clothes

touch the optical pickup.

1MΩ

Conductive material

(sheet) or steel sheet

Anti-static wrist strip

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

CDR-HD1300E

■FRONT PANELS

CDR-HD1300

■REAR PANELS

CDR-HD1300 (U model)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

CDR-HD1300 (A model)

CDR-HD1300 (B, G models)

CDR-HD1300 (J model)

CDR-HD1300E (B, G models)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

■REMOTE CONTROL PANEL

435 (17-1/8")

100

(3-15/16")

15.5

(5/8")

115.5

(

4-9/16"

)

11.5

(7/16")

8.3

(5/16")

394.7 (15-1/2")

414.5

(

16-5/16"

)

Unit : mm (inch)

単位:mm（インチ）

■SPECIFICATIONS / 参考仕様

GENERAL / 一般仕様

Model / モデル ..................................................... HDD / CD recorder

Application disks / 対応ディスク ... CDs, CD-Rs for AUDIO, CD-

RWs for AUDIO

HDD capacity / HDD容量 ................ 40GB (CDR-HD1300E) and up

to 137GB by replacing

Power supply / 電源電圧

U model ................................................................ AC 120 V 60 Hz

A model ................................................................ AC 240 V 50 Hz

B, G models ......................................................... AC 230 V 50 Hz

J model ........................................................... AC 100 V 50/60 Hz

Power consumption / 消費電力

U, A, B, G models ................................................................. 37 W

J model .................................................................................. 32 W

Standby power consumption / 待機電力 .................................. 0 W

Operating temperature / 動作温度 ........................ + 5 °C to + 35 °C

Max. dimensions / 最大寸法 (W x H x D)

................ 435 x 115.5 x 414.5 mm (17-1/8" x 4-9/16" x 16-5/16")

(include legs, terminals and knobs)

Weight / 質量

CDR-HD1300 with no HDD ......................... 7.8 kg (17 lbs. 3 oz.)

CDR-HD1300E with HDD ............................ 8.4 kg (18 lbs. 8 oz.)

Panel color / パネル色

Gold Color .................................................................. G, J models

Black Color ....................................................... U, A, B, G models

AUDIO PERFORMANCE / オーディオ性能

Output level / 出力レベル (1kHz 0dB) ......................... 2 ±0.5 Vrms

Frequency characteristics / 周波数特性 (EIAJ)

5Hz to 20kHz.................................................................... ±0.5 dB

Playback signal to noise ratio / 再生SN比 (EIAJ)

...............................................................................105 dB or more

• DIMENSIONS

Playback dynamic range / 再生ダイナミックレンジ (EIAJ)

.................................................................................99 dB or more

Playback THD + noise / 再生歪率+雑音 (EIAJ)

...............................................................................0.004 % or less

Recording signal to noise ratio / 録音SN比 (EIAJ)

.................................................................................92 dB or more

Recording dynamic range / 録音ダイナミックレンジ (EIAJ)

.................................................................................92 dB or more

Recording THD + noise / 録音歪率+雑音 (EIAJ)

...............................................................................0.006 % or less

INPUT/OUTPUT / 入出力仕様

LINE OUTPUT / ライン出力

Output level ........................................................................ 2 Vrms

Output resistance ........................................................... 990 ohms

LINE INPUT / ライン入力

Input sensitivity ........................................................... 500 mVrms

Input impedance .......................... 24 k-ohms (REC LEVEL Max.)

DIGITAL OUTPUT / デジタル出力

Coaxial output level ....................................... 0.5 Vp-p (75 ohms)

Optical output level .......................................................... -20 dBm

Sampling frequency ........................................................ 44.1 kHz

DIGITAL INPUT / デジタル入力

Coaxial input level .......................................... 0.5 Vp-p (75 ohms)

Optical input level ............................................................ -20 dBm

Input gain (with Digital Volume)......................................... ±12 dB

Input gain (without Digital Volume) ..................................... ±0 dB

Sampling frequency tolerance

........................................... 32 kHz, 44.1 kHz, 48 kHz and 96 kHz

HEADPHONE OUTPUT / ヘッドホン出力 (PHONES LEVEL MAX)

Output level (-20 dB, 150 ohms load) ........................ 300 mVrms

* Specifications are subject to change without notice due to product

improvements.

※ 参考仕様および外観は予告なく変更されることがあります。

U .......... U.S.A. model A ...... Australian model

B .......... British model G ...... European model

J ........... Japanese model

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

■INTERNAL VIEW

1OSD (2) P.C.B. (U, J models only)

2OPERATION (6) P.C.B.

3OPERATION (7) P.C.B.

4OSD (1) P.C.B.

5MAIN P.C.B.

6HDD UNIT

7OPERATION (1) P.C.B.

8OPERATION (2) P.C.B.

9CDR MECHANICAL UNIT

0OPERATION (3) P.C.B.

AOPERATION (5) P.C.B.

BOPERATION (4) P.C.B.

12 3 4 5 6

89AB0 7

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

Top Cover

トップカバー

Front Panel Unit

フロントパネルユニット

Hook

フック

Hook

フック

Fig. 1

(Remove parts in the order as numbered.)

CDR Mechanical Unit replacement

•The CDR mechanical unit must be replaced as a unit.

None of its components can be supplied separately.

•When replacing the CDR mechanical unit, write down

the following items.

•Serial No. of the product and the symptom in detail

•Mechanical serial No./mechanical shipping serial

No. of the CDR mechanical unit

•When sending back the defective CDR mechanical unit

for repair, send the whole unit.

•When sending back the defective CDR mechanical unit

for repair, attach the disc that was used when the error

occurred, if requested. However, Yamaha shall not be

liable even if the data in the disc has become

unreadable while the unit is being serviced/repaired.

•When replacing the CDR mechanical unit, be sure to

order a laser precaution label and a radiation sheet as

spare parts and attach them to the new CDR

mechanical unit. (Refer to the figure 6 and 7 in P11.)

•After replacing the CDR mechanical unit, be sure to

update the CD-R/W drive firmware to the latest version.

■DISASSEMBLY PROCEDURES / 分解手順

1. Removal of Top Cover

a. Turn off the power and disconnect the power plug from

the AC power outlet.

b. Remove 4 screws (1) and 3 screws (2). (Fig. 1)

c. Remove the top cover rearward while lifting it up. (Fig.

2. Removal of Front Panel Unit

a. Remove 3 screws (3) and 4 screws (4). (Fig. 1)

b. While pushing in hooks on both sides of the panel,

remove the front panel unit forward. (Fig. 1)

（番号順に部品を取り外してください。）

CDRメカユニットの交換

・ CDRメカユニットは、ユニット交換となります。小部

品の部品供給はできません。

・ CDRメカユニットを交換するときは、下記の事項を控

えてください。

・製品の製造番号と詳しい症状

・CDRメカユニットのメカ製番/メカ出荷製番

・故障したCDRメカユニットは、修理の為にユニットご

と返送してください。

・修理依頼に際しては、必要に応じて、エラーが起きたと

きのディスクを添付するようにお願いします。

ただし、当社はサービス/修理中にディスクのデータが

読み取れなくなってもその責務を負いません。

・ CDRメカユニット交換の際には、レーザー注意文のラ

ベルおよび放熱シートも部品発注して、新しいCDRメ

カユニットに貼り付けてください。（11ページのFig.6

および7参照）

・ CDRメカユニットを交換したときには、CD-R/Wドライ

ブファームウエアを最新版に更新してください。

1. トップカバーの取り外し

a. 電源を切り、AC電源コンセントから電源プラグを抜き

ます。

b. ①のネジ4本、②のネジ3本を外します。（Fig.1）

c. トップカバーを持ち上げながら後方へ外します。（Fig.

1）

2. フロントパネルユニットの取り外し

a. ③のネジ3本、④のネジ4本を外します。（Fig.1）

b. パネル両サイドのフックを押し込みながら、フロントパ

ネルユニットを前方に外します。（Fig.1）

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CDR-HD1300/CDR-HD1300E

3. CDRメカユニットの取り外し

a. リアパネルの⑤のネジ2本をゆるめ、HDDスロットドア

を開きます。（Fig.2）

b. 作業の妨げにならないように、HDDトレイを約5.5cm引

き出します。（Fig.3）

Fig. 2 Fig. 3

Power Cable

電源ケーブル

IDE Cable

IDEケーブル

CDR Mechanical Unit

CDRメカユニット

Word Clock Cable

ワードクロックケーブル

c. CDRメカユニットから電源ケーブル、IDEケーブル、

ワードクロックケーブルを外します。（Fig.4）

d. ⑥のネジ5本を外し、各ストッパーを外します。（Fig.5）

e. CDRメカユニットを持ち上げながら後方へ取り出しま

す。（Fig.5）

Fig. 4

Stopper A

ストッパーA

Stopper A

ストッパーA

Stopper C

ストッパーC

Stopper B

ストッパーB

CDR Mechanical Unit

CDRメカユニット

Fig. 5

3. Removal of CDR Mechanical Unit

a. Loosen 2 screws (5) on the HDD slot door and open

the HDD slot door. (Fig. 2)

b. Draw the HDD tray forward by about 5.5cm so that it

does not get in the way of the removal work. (Fig. 3)

c. Disconnect the power cable, IDE cable and word clock

cable from the CDR mechanical unit. (Fig. 4)

d. Remove 5 screws (6) and then remove each stopper.

(Fig. 5)

e. Remove the CDR mechanical unit rearward while lifting

it up. (Fig. 5)

4. CDRメカユニットの分解

a. ⑦のネジ4本、⑧のネジ4本を外し、下フレームを外し

ます。（Fig.6）

b. トレーを開ける場合は、底面のマニュアルイジェクトレ

バーを右へ動かして開きます。（Fig.7）

c. リッドを上方へ外します。（Fig.6）

4. Disassembly of CDR Mechanical Unit

a. Remove 4 screws (7) and (8) respectively and then

remove the lower frame. (Fig. 6)

b. To open the tray, move the manual eject lever located

on the bottom face. (Fig. 7)

c. Remove the lid upward. (Fig. 6)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

This manual suits for next models

Table of contents

Other Yamaha Recording Equipment manuals

Popular Recording Equipment manuals by other brands

ThermoFisher Scientific

ThermoFisher Scientific Dionex DRS 600 Installation checklist

Shure

Shure ANIUSB-Matrix user guide

Nady Audio

Nady Audio HE-1 user guide

AUDAC

AUDAC APM 01 User manual & installation guide

Teac

Teac GF-350 owner's manual

Fractal Audio

Fractal Audio MFC-101 MARK III owner's manual

bmcm

bmcm USB-OI16 manual

HHB

HHB BurnIT CDR-830 Service manual

GE VersaMax IC200CPUE05 manual

IntesisBox

IntesisBox MH-RC-MBS-1 user manual

Attero Tech

Attero Tech unD4l user manual

Sennheiser

Sennheiser UI 765 instruction manual

Sony

Sony RCD-W1 Operating Instructions (primary... Service manual

Roland

Roland Planet-P MKS-10 owner's manual

Roland

Roland BOSS GT-PRO Turbostart

8x8 Inc

8x8 Inc Valcom V-2001A manual

Waves

Waves SUB Align user guide

Mitsubishi Electric

Mitsubishi Electric MAC-334IF-E installation manual

Yamaha CRD-HD1300 User manual

Popular Recording Equipment manuals by other brands