Yamaha MCX-SP10 - Left / Right CH Speakers User manual

•••
MusicCAST --
Speaker System
Systeme D' enceintes
MCX-SP10
OWNER'S MANUAL
MODE D'EMPLOI
BEDIENUNGSANLEITUNG
•••
MusicCAST --
Speaker System
Systeme D' enceintes
MCX-SP10
OWNER'S MANUAL
MODE D'EMPLOI
BEDIENUNGSANLEITUNG

PRECAUTIONS
Read this before using the speaker.
• To assure the finest performance, please read this manual
carefully. Keep it in asafe place for future reference.
•Install the speaker in acool, dry, clean place -away
from windows, heat sources, sources
of excessive
vibration, dust, moisture and cold. Avoid sources
of
humming (transformers, motors). To prevent fire or
electrical shock, do not expose the speaker to rain or
water.
•
To prevent the enclosure from warping or discoloring,
do not place the speaker where it will be exposed to
direct sunlight or excessive humidity.
•Do not
plac;e the following objects on the speaker:
Glass, china, etc.
If glass etc. falls by vibrations and breaks, it may
cause personal injury.
Aburning candle etc.
If the candle falls by vibrations, it may cause fire
and personal injury.
Avessel with water in it
If the vessel falls by vibrations and water spills, it
may cause damage to the speaker, and/or you may
get an electri.c shock.
•Do not place the speaker where foreign objects such
as
water drips might fall. It might cause afire, damage to
the speaker, and/or personal injury.
•Do not place the speaker where it is liable to be
knocked over or struck by falling objects. Stable
placement will also ensure better sound performance.
•Placing the speaker on the same shelf or rack as a
turntable can result in feedback.
•Never put ahand or aforeign object into the port
located on the rear
of the speaker as this might cause
personal injury and/or damage to the speaker.
•When moving the speaker, do not hold the port as it
might cause personal injury and/or damage to the
speaker.
•Any time you note distortion, reduce the volume
control on your MCX-AIO to alower setting. Never
allow your MCX-AIO
to be driven into "clipping".
Otherwise the speaker may be damaged.
•When using acomponent with arated output power
higher than the nominal input power
of the speaker,
care should be taken never to exceed the speaker's
maximum input.
•Do not attempt to clean the speaker with chemical
solvents as this might damage the finish. Use aclean,
dry cloth.
•Do not attempt to modify or fix the speaker. Contact
qualifiedYAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reasons.
•Secure placement or installation is the owner's
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation
of the speaker.
SU'PPLIED ACCESSORIES ' '.
After unpacking, check that the following parts are supplied.
Speaker cable (5 m) x 2 Pad
x4
n
PRECAUTIONS
Read this before using the speaker.
• To assure the finest performance, please read this manual
carefully. Keep it in asafe place for future reference.
•Install the speaker in acool, dry, clean place -away
from windows, heat sources, sources
of excessive
vibration, dust, moisture and cold. Avoid sources
of
humming (transformers, motors). To prevent fire or
electrical shock, do not expose the speaker to rain or
water.
•
To prevent the enclosure from warping or discoloring,
do not place the speaker where it will be exposed to
direct sunlight or excessive humidity.
•Do not
plac;e the following objects on the speaker:
Glass, china, etc.
If glass etc. falls by vibrations and breaks, it may
cause personal injury.
Aburning candle etc.
If the candle falls by vibrations, it may cause fire
and personal injury.
Avessel with water in it
If the vessel falls by vibrations and water spills, it
may cause damage to the speaker, and/or you may
get an electri.c shock.
•Do not place the speaker where foreign objects such
as
water drips might fall. It might cause afire, damage to
the speaker, and/or personal injury.
•Do not place the speaker where it is liable to be
knocked over or struck by falling objects. Stable
placement will also ensure better sound performance.
•Placing the speaker on the same shelf or rack as a
turntable can result in feedback.
•Never put ahand or aforeign object into the port
located on the rear
of the speaker as this might cause
personal injury and/or damage to the speaker.
•When moving the speaker, do not hold the port as it
might cause personal injury and/or damage to the
speaker.
•Any time you note distortion, reduce the volume
control on your MCX-AIO to alower setting. Never
allow your MCX-AIO
to be driven into "clipping".
Otherwise the speaker may be damaged.
•When using acomponent with arated output power
higher than the nominal input power
of the speaker,
care should be taken never to exceed the speaker's
maximum input.
•Do not attempt to clean the speaker with chemical
solvents as this might damage the finish. Use aclean,
dry cloth.
•Do not attempt to modify or fix the speaker. Contact
qualifiedYAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reasons.
•Secure placement or installation is the owner's
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation
of the speaker.
SU'PPLIED ACCESSORIES ' '.
After unpacking, check that the following parts are supplied.
Speaker cable (5 m) x 2 Pad
x4
n

MOUNTING THE SPEAKERS ON A WALL
Follow the procedure below to remove the speaker
stand before attempting to mount it on awall.
1.Use ascrewdriver to loosen the screws
attaching the stand to the speaker.
2. Remove the stand from the speaker,
taking care to slide out the mounting
pins that hold the stand to the bottom of
the speaker.
3. Attach the pads to the rear of the
speaker, as illustrated.
4. Insert 2self-tapping screws (diameter:
3.5 to 4mm) into the wall, 40 mm apart.
40mm
5. Mount the speaker on the screws by
positioning it so that the screws on the
wall fit snugly into the holes on the
mounting bracket.
4mm 20mm or more
•This speaker weighs 1.2 kg (2lbs 10 oz). Do not mount it
on thin plywood or awall with soft surface material.
If
mounted, the screws may come loose from the flimsy
surface and the speaker may fall. This damages the speaker
and may cause personal injury.
•Do not use nails, adhesives, or other unstable materials to
mount the speakers. Long-term use and vibrations may
cause it to fall.
•
To avoid accidents resulting from tripping over loose
speaker cable, fix it to the wall.
•This speaker features amagnetically shielded design, but
there is still achance that placing it too close to aTV set
might impair picture color. Should this happen, move the
speaker away from the TV set.
MOUNTING THE SPEAKERS ON A WALL
Follow the procedure below to remove the speaker
stand before attempting to mount it on awall.
1.Use ascrewdriver to loosen the screws
attaching the stand to the speaker.
2. Remove the stand from the speaker,
taking care to slide out the mounting
pins that hold the stand to the bottom of
the speaker.
3. Attach the pads to the rear of the
speaker, as illustrated.
4. Insert 2self-tapping screws (diameter:
3.5 to 4mm) into the wall, 40 mm apart.
40mm
5. Mount the speaker on the screws by
positioning it so that the screws on the
wall fit snugly into the holes on the
mounting bracket.
4mm 20mm or more
•This speaker weighs 1.2 kg (2lbs 10 oz). Do not mount it
on thin plywood or awall with soft surface material.
If
mounted, the screws may come loose from the flimsy
surface and the speaker may fall. This damages the speaker
and may cause personal injury.
•Do not use nails, adhesives, or other unstable materials to
mount the speakers. Long-term use and vibrations may
cause it to fall.
•
To avoid accidents resulting from tripping over loose
speaker cable, fix it to the wall.
•This speaker features amagnetically shielded design, but
there is still achance that placing it too close to aTV set
might impair picture color. Should this happen, move the
speaker away from the TV set.

CONNECTING TO YOUR MCX-A10
Before making connections, make sure that the MCX-AIO is switched off.
•Connections
•Connect the push-type input terminals at the rear
of the speakers to the SPEAKER OUT terminals
of the MCX-AIO with the speaker cable provided.
•Connect the (+) terminals on the MCX- Al 0and
the speakers using one side of the cable. Connect
the
(-) terminals on both components using the
other side
of the cable.
•Connect one speaker to the left (marked L)
terminals
of your MCX-AIO, and the other
speaker to the right (marked R) terminals, making
sure not to reverse the polarity (+, -). If one
speaker is connected with reversed polarity, the
sound will be unnatural and lack bass.
•How to connect
1. Press and hold the terminal's tab.
2. Remove the insulation coating at the
extremity of each speaker cable by
twisting the coating off.
3. Insert the bare wire.
4. Release the tab to allow it to lock
securely
on the cable's wire end.
Gray line
MCX-SP10
RedBlack
MCX-SP10
(Right) (Left)
l
MCX-A10
•This speaker is specifically designed for use with the MCX-AIO. If you connect it to any other component, take care not to
damage the speaker by exceeding its rated input.
•Do not let the bare speaker wires touch each other
as this could damage the speaker or the MCX-AIO, or both of them.
II
CONNECTING TO YOUR MCX-A10
Before making connections, make sure that the MCX-AIO is switched off.
•Connections
•Connect the push-type input terminals at the rear
of the speakers to the SPEAKER OUT terminals
of the MCX-AIO with the speaker cable provided.
•Connect the (+) terminals on the MCX- Al 0and
the speakers using one side of the cable. Connect
the
(-) terminals on both components using the
other side
of the cable.
•Connect one speaker to the left (marked L)
terminals
of your MCX-AIO, and the other
speaker to the right (marked R) terminals, making
sure not to reverse the polarity (+, -). If one
speaker is connected with reversed polarity, the
sound will be unnatural and lack bass.
•How to connect
1. Press and hold the terminal's tab.
2. Remove the insulation coating at the
extremity of each speaker cable by
twisting the coating off.
3. Insert the bare wire.
4. Release the tab to allow it to lock
securely
on the cable's wire end.
Gray line
MCX-SP10
RedBlack
MCX-SP10
(Right) (Left)
l
MCX-A10
•This speaker is specifically designed for use with the MCX-AIO. If you connect it to any other component, take care not to
damage the speaker by exceeding its rated input.
•Do not let the bare speaker wires touch each other
as this could damage the speaker or the MCX-AIO, or both of them.
II

The front cover is fastened to the enclosure at four
points and can be removed if desired. To remove
the cover, hold on to both sides and slowly pull
straight away from the speaker.
To reattach, line up
the four holes on the inner surface of the cover with
the four corresponding pegs on the speaker and
push gently.
•When the cover is removed, take care not to touch the
speaker units with your hands or to exert excessive force
with tools.
II
SPECIFICATIONS
Type 2-way bass reflex speaker system
Magnetic shielding type
Driver 10 cm (4") cone woofer
2.5
cm (I") dome tweeter
Impedance 4Q
Frequency Response 100 Hz to 27 kHz
Nominal Input Power 20 W
Sensitivity 89 dB/2.83 V 1m
Dimensions (WxHxD) 210 x210 x79 mm
(8-5/16" x8-5116" x3-1/10")
Weight 1.2 kg (2lbs 100z) x 2
•Specifications are subject to change without
notice due to product improvements.
•Care should be taken not to exceed the input
power values noted above.
The front cover is fastened to the enclosure at four
points and can be removed if desired. To remove
the cover, hold on to both sides and slowly pull
straight away from the speaker.
To reattach, line up
the four holes on the inner surface of the cover with
the four corresponding pegs on the speaker and
push gently.
•When the cover is removed, take care not to touch the
speaker units with your hands or to exert excessive force
with tools.
II
SPECIFICATIONS
Type 2-way bass reflex speaker system
Magnetic shielding type
Driver 10 cm (4") cone woofer
2.5
cm (I") dome tweeter
Impedance 4Q
Frequency Response 100 Hz to 27 kHz
Nominal Input Power 20 W
Sensitivity 89 dB/2.83 V 1m
Dimensions (WxHxD) 210 x210 x79 mm
(8-5/16" x8-5116" x3-1/10")
Weight 1.2 kg (2lbs 100z) x 2
•Specifications are subject to change without
notice due to product improvements.
•Care should be taken not to exceed the input
power values noted above.

_YAMAHA
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC
LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO MiS 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEl HAMBURG,
F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK)
LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETIERGRENS
GATA 1, BOX 30053, 400 43 VASTRA FROLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA
PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
YAMAHA CORPORATION
Printed in China UPIIlDfO WB49070
_YAMAHA
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC
LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO MiS 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEl HAMBURG,
F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK)
LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETIERGRENS
GATA 1, BOX 30053, 400 43 VASTRA FROLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA
PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
YAMAHA CORPORATION
Printed in China UPIIlDfO WB49070